1972 Porsche 911 Brake Parts

The Original Equipment brand brake disc is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.

Product Features:

• OE-Equivalent and Direct fit Application
• made of special cast iron with high carbon content
• Provides a higher friction coefficient.
• Resistant to vibrations and noise.
• Contains the same high quality craftsmanship as the original equipment manufacturer.
• Guarantees OE quality performance, durability and fitment.

Carquest Wearever rotors meet or exceed original equipment specifications while delivering superior stopping power. Carquest Wearever rotors are manufactured with proper harmonic design and non-directional finish that eliminate noise and enhance pedal feel. Our rotors are designed to effectively dissipate heat, helping to eliminate brake fade and increase the life of your pads and rotors. Carquest Wearever rotors are designed for long-lasting and quiet braking with superior performance.

Product Features:

• Meets or exceeds OE design for superior stopping power
• Exceeds ISO manufacturing guidelines (International Organization for Standardization)
• Matches OE vane size for proper cooling
• Optimal metallurgy and casting thickness to prevent warping
• Air gap eliminates brake fade and increases pad life
• Non-Directional finish decreases break-in time

Parking Brake Shoe

Wearever brake shoes are 100% new OE replacement brake shoes and come with coated steel to guard against rust, salt and road grime. Wearever brake shoes provide exceptional stopping power, virtually noise free and exact fitment to the original equipment brake shoes.

Product Features:

• Wearever Brake Shoes come bonded or riveted based on OE design.
• Wearever Brake Shoes are coated to prevent rust.
• Wearever Brake Shoes are 100% New not remanufactured.
• Brand may vary by location

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

• Each unit is 100% new, providing consistent performance when servicing your brake system
• Easy to transfer for on-the-spot master cylinder bleeding
• Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
• Easy to clean to ensure no cross contamination
• Durability for long lasting performance

This part matches Original Equipment (OE) quality specifications which means that it is at least as good if not better than the original part the manufacturer supplied the car with. TRW has introduced Cotec – an innovative coating for its brake pads. Independent tests have proven that Cotec achieves significantly shorter stopping distances than the brake pads of major competitors or even OE, for the first stops after leaving a garage following a brake pad change. In the normal bedding in process there is a period, known as the green behavior of the pad, which occurs at the start of the bedding in process where the friction co-efficient is lower than usual. Drivers can find it difficult to adjust to the difference in performance during these first stops. TRW Cotec brake pads address this issue by improving the contact between the brake disc and pad. The friction material is the most important part of a brake pad. All TRW’s brake pads contain the optimum mix of raw materials from rubber to graphite. TRW has made a significant investment over the years to ensure that we have the perfect mix – and we make it in-house. The ingredients ensure a stable friction coefficient and the safest braking performance in all temperatures, at all speeds and under all conditions. The backing plates used by TRW are designed, patented and produced in-house to OE specification. They are fitted to the friction material with a unique adhesive compound which can withstand high temperatures and resists extremely high shear strengths. TRW places great emphasis on noise reduction and its brake pads are fitted with high quality shims which act as a damper between the friction material and the brake caliper. TRW friction components are not only tested in our NVH (noise vibration harshness) laboratories and also on the road.

Product Features:

• Include the OE specified shims.
• Low noise and reduced vibrations.
• Formulated to OE Specifications.
• Superior friction qualities.
• Organic blended compound.

Carquest Premium Gold brake pads are original equipment replacement brake pads that provide consistent, quiet, and clean braking.

Product Features:

• Application-specific formulations designed for extended pad life and clean wheels
• Multi-layer shim for near silent braking
• OE designed slots and chamfers for consistent performance
• Hardware included on popular and late-model applications

Carquest Wearever Gold brake pads are original equipment replacement brake pads that provide consistent, quiet, and clean braking.

Product Features:

• Application-specific formulations designed for extended pad life and clean wheels
• Multi-layer shim for near silent braking
• OE designed slots and chamfers for consistent performance
• Hardware included on popular and late-model applications

Carquest Wearever Gold brake pads are original equipment replacement brake pads that provide consistent, quiet, and clean braking.

Product Features:

• Application-specific formulations designed for extended pad life and clean wheels
• Multi-layer shim for near silent braking
• OE designed slots and chamfers for consistent performance
• Hardware included on popular and late-model applications

Carquest Professional Platinum brake pads are the optimal braking solution that provide an unmatched level of performance and reliability. These brake pads are engineered by an Original Equipment Manufacturer (O.E.M.) that meets IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. We use an industry-leading number of friction formulations for maximum performance and extended pad life on each application. Carquest Professional Platinum brake pads also utilize a patented 4-layer HEX shim, now upgraded with aramid fibers, to provide quiet braking and reduce shim wear. These brake pads are also supplied with coated brake hardware and caliper pin grease for nearly every application. Carquest Professional Platinum brake pads are the ideal choice when looking for shorter stopping distances, quiet braking and longer-lasting brakes.

Product Features:

• Industry-leading number of application specific formulations for maximum performance and extended pad life
• On-vehicle testing similar to original equipment tests
• Patented 4-Layer HEX Shim Technology provides quiet braking
• HEX shim design utilizes aramid fibers, the same fibers used in bulletproof vests, to reduce shim wear
• Burnishing compound allows for a faster break-in of pads and rotors
• PTFE coated hardware and caliper pin grease included for nearly every application
• Powder-coated backing plate prevents corrosion

This part matches Original Equipment (OE) quality specifications which means that it is at least as good if not better than the original part the manufacturer supplied the car with. TRW has introduced Cotec – an innovative coating for its brake pads. Independent tests have proven that Cotec achieves significantly shorter stopping distances than the brake pads of major competitors or even OE, for the first stops after leaving a garage following a brake pad change. In the normal bedding in process there is a period, known as the green behavior of the pad, which occurs at the start of the bedding in process where the friction co-efficient is lower than usual. Drivers can find it difficult to adjust to the difference in performance during these first stops. TRW Cotec brake pads address this issue by improving the contact between the brake disc and pad. The friction material is the most important part of a brake pad. All TRW’s brake pads contain the optimum mix of raw materials from rubber to graphite. TRW has made a significant investment over the years to ensure that we have the perfect mix – and we make it in-house. The ingredients ensure a stable friction coefficient and the safest braking performance in all temperatures, at all speeds and under all conditions. The backing plates used by TRW are designed, patented and produced in-house to OE specification. They are fitted to the friction material with a unique adhesive compound which can withstand high temperatures and resists extremely high shear strengths. TRW places great emphasis on noise reduction and its brake pads are fitted with high quality shims which act as a damper between the friction material and the brake caliper. TRW friction components are not only tested in our NVH (noise vibration harshness) laboratories and also on the road.

Product Features:

• Include the OE specified shims.
• Low noise and reduced vibrations.
• Formulated to OE Specifications.
• Superior friction qualities.
• Organic blended compound.

The Power Stop Z17 Evolution Plus ceramic brake pads feature a ceramic formula designed to maximize stopping power while reducing brake dust & eliminating noise. Using OE positive mold technology along with a thermal scorched pad surface, Z17 pads maintain consistent wear and performance while ensuring a fast break-in. Stainless steel hardware is included with the Z17 brake pads making it easier to complete your brake job. The Power Stop Z17 Evolution Plus ceramic brake pads are an affordable stock replacement for all vehicles.

Product Features:

• Low-dust ceramic formula designed to maximize stopping power and keep wheels clean
• Positive mold technology for consistent wear and performance
• Thermal scorched pad surface for a fast break-in
• Chamfered and slotted to ensure noise free braking
• Powder coated backing plate resists rust and corrosion to provide extended pad life
• Multi-Layer rubberized shims provide virtually noise-free braking
• Includes Premium stainless-steel hardware for easy installation

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

• OE quality direct fit application.
• Friction Ready
• Corrosion inhibiting protection
• Ensures long life and maximum performance
• Natural exterior finish

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

• OE quality direct fit application.
• Friction Ready
• Corrosion inhibiting protection
• Ensures long life and maximum performance
• Natural exterior finish

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

• OE quality direct fit application.
• Friction Ready
• Corrosion inhibiting protection
• Ensures long life and maximum performance
• Natural exterior finish

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

• OE quality direct fit application.
• Friction Ready
• Corrosion inhibiting protection
• Ensures long life and maximum performance
• Natural exterior finish

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

• OE quality direct fit application.
• Friction Ready
• Corrosion inhibiting protection
• Ensures long life and maximum performance
• Natural exterior finish

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

• OE quality direct fit application.
• Friction Ready
• Corrosion inhibiting protection
• Ensures long life and maximum performance
• Natural exterior finish

FTE Disc Brake Caliper Repair Kit contains the components necessary for repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

• Guaranteed factory fit to original equipment specifications
• Meets or exceeds original equipment factory safety standards

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

• Guaranteed factory fit to original equipment specifications
• Meets or exceeds original equipment factory safety standards

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

• Guaranteed factory fit to original equipment specifications
• Meets or exceeds original equipment factory safety standards

FTE Disc Brake Caliper Repair Kit contains the components necessary for repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

• Guaranteed factory fit to original equipment specifications
• Meets or exceeds original equipment factory safety standards

FTE Disc Brake Caliper Repair Kit contains the components necessary for repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

• Guaranteed factory fit to original equipment specifications
• Meets or exceeds original equipment factory safety standards

TRW Automotive supplies master cylinder brake actuation systems featuring quality and performance. TRW’s master cylinder product portfolio covers a wide range of vehicles, from small cars up to truck and SUV platforms. These systems can offer lighter weight, with options such as micro master cylinders and aluminum master cylinders through to heavy-duty master cylinders designed for the durability and variable loading conditions of the light-truck market. These systems function with the help of a series of brake fluid sensors, which are located on the reservoir tank. This series includes vacuum sensors, brake light switches, and travel sensors.

Product Features:

• Low volume uptake
• High efficiency
• Low pressure differential between primary and secondary circuits
• Good bleedability
• Cr6-free surfaces for vehicles built from July 2007 (as required by law)
• Central valve version suitable for ABS

As the basis for a standardized ATE concept for future tandem master cylinders, ATE has developed a new plunger generation which has many technical enhancements and advantages.

Product Features:

• Short closing paths
• Low volume uptake
• High efficiency
• Low throttling / after-suction resistance
• Low pressure differential between primary and secondary circuits
• Good bleedability
• Cr6-free surfaces for vehicles built from July 2007 (as required by law)
• Central valve version suitable for ABS
• Compact design – ideal for installation in small spaces
• Reduced weight – by roughly 20% compared to conventional central valve technology
• Fewer components – almost half as many as compared to conventional technologies
• Modular system – diameters from 14.29 to 31.75mm and strokes up to 46mm
• Low volume uptake – minimized elastic deformations due to smaller seals
• Sealing cups supported in the housing – robustness against soiling and wear; longer life
• Cr6-free surfaces for vehicles built from July 2007 (as required by law)

As the basis for a standardized ATE concept for future tandem master cylinders, ATE has developed a new plunger generation which has many technical enhancements and advantages.

Product Features:

• Short closing paths
• Low volume uptake
• High efficiency
• Low throttling / after-suction resistance
• Low pressure differential between primary and secondary circuits
• Good bleedability
• Cr6-free surfaces for vehicles built from July 2007 (as required by law)
• Central valve version suitable for ABS
• Compact design – ideal for installation in small spaces
• Reduced weight – by roughly 20% compared to conventional central valve technology
• Fewer components – almost half as many as compared to conventional technologies
• Modular system – diameters from 14.29 to 31.75mm and strokes up to 46mm
• Low volume uptake – minimized elastic deformations due to smaller seals
• Sealing cups supported in the housing – robustness against soiling and wear; longer life
• Cr6-free surfaces for vehicles built from July 2007 (as required by law)

TRW Automotive supplies master cylinder brake actuation systems featuring quality and performance. TRW’s master cylinder product portfolio covers a wide range of vehicles, from small cars up to truck and SUV platforms. These systems can offer lighter weight, with options such as micro master cylinders and aluminum master cylinders through to heavy-duty master cylinders designed for the durability and variable loading conditions of the light-truck market. These systems function with the help of a series of brake fluid sensors, which are located on the reservoir tank. This series includes vacuum sensors, brake light switches, and travel sensors.

Product Features:

• Low volume uptake
• High efficiency
• Low pressure differential between primary and secondary circuits
• Good bleedability
• Cr6-free surfaces for vehicles built from July 2007 (as required by law)
• Central valve version suitable for ABS