from

$17.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

from

$52.99

A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.

Product Features:

Gains Both Performance and Longevity
Will Handle Any and All Torque
Out Lasts Rubber

from

$840.99

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some Holeshots.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$37.99

Spectre’s High Performance Replacement Air Filters are engineered to outperform ordinary paper filters by providing increased air flow for improved performance. Manufactured using high quality materials including pre-dyed synthetic media, urethane, and steel mesh, this performance air filter is factory pre-oiled and ready to use.

Product Features:

High performance and high air flow filter
Filter media is non-woven synthetic and pre-dyed
Replaces stock air filter
Easy to install with no special tools or skills required
Reinforced with a steel mesh

from

$58.99

These ACCEL wire sets are a true performance upgrade replacement for OE types. Efficient delivery of spark energy for a good price. Silicone boots with blue, black, red and yellow wire, zinc-plated steel terminals. Tinned copper core.

Product Features:

Graphite Suppression Eliminates RFI/EMI
3000 To 7000 Ohms Per Foot Of Resistance
Silicone Spark Plug Boots
450 Degree Temperature Rating

from

$206.99

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:

High Output Fuel Flow
Flows 110 gph Free Flow
Shutoff Pressure Pre-Set From 6.5 To 8 PSI
Fuel Pressure Regulator Is Not Required
Heavy Duty Construction For Continuous High rpm Operation
Fuel Body Casting Can Be Rotated For Various Plumbing Situations
Inlet And Outlet Tapped For 1/4 in. NPT

from

$125.99

Kits include most popular chrome dress-up components, including short, OEM height valve covers with integral oil baffles.

Product Features:

Includes oil baffles
Chrome plated

from

$435.99

Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.

Product Features:

Certified Billet Material
Borg and Beck Clutch Pattern
Long-Style Clutch Pattern
Ring Gear Securely Mounted To Prevent Spinning

from

$48.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$25.99

Product Features:

Service Part
Makes Connections Quick And Easy

from

$409.99

The award-winning Quarter Stick automatic shifter is designed to provide positive gear change control for street or racing transmission applications. Gated mechanism. NHRA/IHRA approved reverse lockout.

Product Features:

Forward and Reverse Shift Patterns
Chrome Plated Trigger for Detent Activity
Factory Neutral Safety Switch
Compact And Lightweight
Roller Detent with Shifter Pattern

from

$79.99

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

More Accurate Ignition Timing
Improves Performance
Provides More Accurate Ignition Timing
Easy To Install w/Hand Tools
Reduced Maintenance
Thermal Clad Based Surface Mount Construction
Utilizes Specialized Electronic Circuitry
Ignition Timing Is Stable From 1 To 10000rpm

from

$35.99

Manufactured from high-density cork and rubber blend gasket material. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For OE replacement and high performance street.

Product Features:

One-piece design
Eliminates potential leaks
Prevents over tightening
Prevents torque loss

from

$98.99

These coils feature advanced bobbin technology, highly specialized silicone magnetic steel cores, along with optimized winding, resistance and turns ratios to delivery 10-15 percent more energy than the OEM coils. Specialized high temperature epoxy resist

Product Features:

Oil Filled For Better Cooling
Optimized Low Resistance
Silicon Magnetic Steel E-Core
Higher Energy/Voltage Outputs
Quicker Starts
Improved Idle Quality
Resists Shock And Vibration
Resists Corrosion

from

$464.99

New or reconditioned 650cfm. Square-flange. Electric choke without EGR. Primary jet 0.095. Secondary jet 0.098. Metering Rod 0.065 x 0.047. Dual plane intake. Spring loaded needles and seat increase performance. New qwik-tune adjustable secondary air valve. Distinctive black accented hardware. Lightweight ball burnished aluminum. No gaskets below fuel level to prevent leakage. Metering rod and step up springs can be changed easily. GM and AMC style throttle linkage.

Product Features:

Spring Loaded Needles/Seat Increase Performance
New Qwik-Tune Adjustable Secondary Air Valve
Distinctive Black Accented Hardware
Lightweight Ball-Burnished Aluminum
No Gaskets Below Fuel Level to Prevent Leakage
Metering Rod/Step Up Springs Can Be Changed Easily
GM/AMC-Style Throttle Linkage

from

$30.99

Thick, molded rubber with steel carrier. Manufactured from high-density cork and rubber blend gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage. Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Available in standard or extra thick to provide additional valve train to cover clearance. For OE replacement, high performance street, drag race and oval track.

Product Features:

Made from cork/rubber compound
Can be reused many times
Thick; fuel-resistant

from

$357.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$18.99

Oil Pan Bolt Kit

from

$25.99

These high performance thermostats are designed to resist large variations in coolant pressures that occur at high RPM’s where coolant temperature and coolant pressure fight for control of the thermostat keeping it from opening at its designated temperature. The balanced HP thermostat features all brass and copper construction, and opens at the right temperature regardless of engine RPM.

Product Features:

High performance
Resists variations in coolant
Brass and copper construction
Opens at right temperature

from

$360.99

RngPnn

from

$1243.99

Designed for carburetor V8 engines. Power increases from 200 to 400 horsepower. Simple to install. Shorter spray bars. More even distribution across the plenum. A more balanced air and fuel ratio. Quicker response time.

Product Features:

Designed For Carbureted V8 Engines
Power Increases From 200-400_ HP
Simple To Install
Shorter Spray Bars
More Even Distribution Across The Plenum
A More Balanced Air/Fuel ratio
Quicker Response Time

from

$2198.99

The Edelbrock #5093 E-Street cylinder heads are designed for use with 1961-1979 Chrysler 361-440 c.i.d. Wedge engine applications. The Edelbrock E-Street cylinder heads offer American made quality and affordable performance. E-Street cylinder heads featur

Product Features:

Complete Pair For Hydraulic Flat Tappet
84cc Combustion Chamber Volume
210cc Intake/70cc Exhaust Runner Volume
2.14 in. Intake/1.81 in. Exhaust Valve Diameter
0.625 in. Deck Thickness

from

$62.99

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for 1959-1980 Chrysler Slant 6 Cylinder engines, this stock profile valve cover features chrome-plated steel construction and a smooth design. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

Designed for 1959-1980 Chrysler Slant 6 Cylinder engines
Sold in pairs
Triple chrome-plated steel construction
Stock height
Features OEM style sealing edge

from

$96.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$549.99

High burst strength woven lining to withstand heat and higher engine RPM. Heavy-duty sprung hub assembly to allow smooth engagement and steady torque transfer without chatter. Recommended for high horsepower street vehicles in addition to occasional drag strip use.

Product Features:

Built As Matched Assembly
Exceptional Performance
Exceptional Durability
Long Term Dependability

from

$23.79

Spectre’s Chrysler water neck fits 1964 and later Chrysler V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

Product Features:

Fits 1964 and later Chrysler V8 engines
Includes bolts
Chrome plated
Easy to install
O-ring/gasket not included

from

$379.99

Our advanced power system line has grown to include starters. Our new APS starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The APS starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement and thousands of starts. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.

Product Features: