1972 Ford Mustang Differentials

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:

• Fits Ford 8″ with 31 spline axles
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits Ford 7.5″
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

One (1) specialty bearing race to adapt small bearing journal into a 3.250″ dropout. This adapter allows the use of a 28 or 31 spline carrier, positraction or locker in a 3.250″ dropout. This is a perfect solution if you are currently running 28 or 31 spline axles but are looking to upgrade to 35 spline later, or are stepping down from 35 spline but don’t want to buy a new dropout.

Product Features:

• Carrier race
• Fits Ford 9″
• Conversion race to install small bearing carrier into 3.250″ dropout

8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.

Product Features:

• Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Product Features:

• CLUTCH PACK KIT 8.8″ FORD 1 KIT PER UNIT

9.25 Chrysler FRONT PINION KIT , 03 & UP DODGE TRUCK .

Product Features:

• Pilot bearing
• Fits Ford 8″

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! This unit has been machined for use in dropouts with a load-bolt. All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

• Fits Ford 9″ with 35 spline axles and loadbolt housing
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

• Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit. Fits 1957-1981 Ford 10 bolt 9 inch ring gear.

Product Features:

• .047″ thick cellulose/nitrile composite gasket material
• Precision die cut
• Reusable

Pinion seal for 7.5″, 8.8″, and 9.75″ Ford, and also 1985-’86 9″ Ford.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Ford 7.5″, 8.8″ and some 9.75″
• 2.785″ O.D.

Standard Open side gear thrust washer for 7.5″ Ford.

Product Features:

• Side gear thrust washer
• Fits Ford 7.5″

3.062″ side adjuster, Only Fits Yukon Ford 9″ Drop Out, new design ONLY.

Product Features:

• Side adjuster
• Fits Ford 9″
• 3.062″ designs only

Product Features:

• Spider gear kit
• Fits Ford 9″ 31 spline open differential
• Includes two side gears, four pinion gears, cross pin shaft, roll pins and spider gear thrust washers.

9″ Yukon 3.250″ aluminum case, HD Drop Out housing, with load bolt. Made from A356-T6 aluminum & featuring a through bolt design, this dropout is rated for up to 1400 horsepower!

Product Features:

• Fits Ford 9″
• 3.250″ carrier race diameter
• A356-T6 aluminum
• Thru-bolt design added strength
• With load bolt

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M88010 race
• All steel construction

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

Adjuster lock bolt 3.062″ & 3.250″ Yukon Ford 9″ Drop Out.

Product Features:

• Side adjuster lock bolt

Pinion gear thrust washer for 8″ and 9″ Ford, Model 20, and 7.25″ Chrysler.

Product Features:

• Pinion gear thrust washer for Ford 8″, Ford 9″ and Chrysler 7.25″

0.260″ diameter cross pin roll pin for 8.75″ Chrysler, 8″, 9″ Ford, and Model 20 and 35.

Product Features:

• Roll pin for Chrysler 8.75″, Ford 8″ and 9″, AMC Model 20 and Model 35
• 0.260″ diameter

Trac Loc clutch guide for 9″ Ford.

Product Features:

• Clutch guide
• Fits Ford 8″ and 9″

Product Features:

• BOLT 9″ FORD OPEN R.G. SAME AS M-4216A200

Product Features:

• Trac Loc spring for Ford 8.8″
• 31 spline applications only

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings

RngPnnInstlKt

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits Ford 8″
• 8.00″ ring gear diameter
• 25 spline pinion
• 10 ring gear bolts
• 4.11 ratio

O-ring for 9″ Ford.Yukon Mighty seal.

Product Features:

• Pinion support o-ring
• Fits Ford 9″