1971 Pontiac LeMans Performance Engines

An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts.

Edelbrock part No: 7829 Performer-Link timing chain is for use with Edelbrock or stock cams. They have a solid-bushing chain for a true bearing surface that rolls with the sprockets, eliminating chain stretch. Cam sprockets are made from 35,000 psi tensile strength cast iron. Crank sprockets are made from billet SAE-1144 steel and induction heat treated. Four Performer-Link sets are stock replacement parts and 50-state legal (see listings in bold type). All other sets have three keyway setting points to ensure accurate timing selection for early or late-model vehicles. Performer-Link timing sets are not for use above 6500 rpm. Performer roller chain sets are engineered to operate up to 6500 rpm. Never hammer directly on chain or sprockets. You can crack the hardened links and pins and cause early failures. Use a sleeve for installations that require hammering, a brass drift punch may be used if you carefully alternate blows on either side of the sprocket to avoid cocking. Never stretch the chain with a screwdriver. Check for clearance between the timing chain and block and between the chain and front cover before reassembly. Be sure that both cam and crank sprockets are exactly in line with each other. Misalignment can cause chain to break.

Weiand Team G Intake Manifold, 7532.

The Tork Master 3000 fits 1965-91 GM TH400, 425, 375 and 1968-81 GM TH350, 375B (not 350C) transmissions. Don’t let the exceptional value fool you into thinking Tork Master Converters are not packed with lots of quality features, making them the best value-priced street performance converters money can buy. These converters perform best when paired with stock to modified engines up to 350hp/350 ft lbs of torque, and lighter weight applications, like street rods. The Tork Master will provide noticeably quicker launches and harder acceleration while maintaining normal daily driving qualities. Upgrades like a new precision alloy steel pump drive tube, needle thrust bearing when factory equipped, new thrust washer between turbine and cover when required, and pressure tested and fully balanced by expertly trained technicians. Notes: Higher stall converters can generate more heat, so we highly recommend adding a transmission cooler. Not recommended for big block, supercharged, plate-type nitrous oxide or trans-brake applications. The product images shown are for illustration purposes only and may not be an exact representation of the product. 10.75-inch bolt circle

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

“Competition Cams Valve Spring, 1.384″” 2 Spring, 988-1. ”

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

“Edelbrock Performer-Plus Camshaft No: 2157 is designed for 350-455 Pontiac V8 engines and produce optimum torque from the low-end to the mid-range. Performer-Plus camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm. The Performer-Plus No: 2157 is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. In the manifold section you’ll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams. All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions. This cam produced 387HP and 439 Ft Lbs of Torque when paired with Performer intake manifold No: 2156 and Performer RPM cylinder heads No: 60599. Camshaft specifications: – Intake duration: 204 Degrees – Exhaust duration: 214 Degrees – Intake lift: .420″” – Exhaust lift: .442″” – Lobe separation: 110 Degree – Intake Center Line: 105 Degree – Vacuum: 15″””

“Edelbrock Performer-Plus Camshaft No: 2103 is designed for 400 Chevy V8 engines and produce optimum torque from the low-end to the mid-range. Performer-Plus camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm. The Performer-Plus No: 2103 is a smooth idling cam for daily drivers, trucks, vans, RVs and 4x4s. You can expect a major improvement in throttle response and torque. In the manifold section you’ll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams. All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions. This cam produced 395 Ft Lbs of Torque when paired with Performer Intake manifold No: 2101 and stock cylinder heads. 50-State Legal E.O. No: D-215-19 for 1957-86 small-block Chevrolet. Camshaft specifications: – Intake duration: 214 Degrees – Exhaust duration: 214 Degrees – Intake lift: .442″” – Exhaust lift: .442″” – Lobe separation: 112 Degree – Intake Center Line: 107 Degree – Vacuum: 15″””

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

The Edelbrock No: 7361 head gaskets provide the best sealing solution and are matched to Edelbrock cylinder heads for optimal performance. Edelbrock relies on industry leading head gasket manufactures to ensure our head gasket sets will provide the best fit and sealing properties when used with Edelbrock aluminum cylinder heads. Edelbrock head gaskets are manufactured from high-density materials and feature a superior design that performs under pressure and provides a long-lasting seal, without re-torqueing.

Weiand Supercharger Accessories, 7134P.

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Edelbrock No: 7251 Engine Water Pump Gasket Set Chevy Small Block. Is it time to rebuild your Edelbrock mechanical water pump- No problem- these Edelbrock water pump gaskets will keep your water pump leak-free. They are manufactured from quality materials and can be installed easily without any modifications

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Competition Cams Magnum Double Row Timing Set for ’65-’88 Ford 255, 289, 302 and Boss 302, 2120.

Competition Cams Ultimate Adjustable Billet Timing Set For Chevrolet 200, 229, 262/Small Block, 8100.

Competition Cams High Energy Timing Set for ’55-’81 Pontiac 265-455, 3212.