1971 Plymouth Roadrunner Drivetrains
More 1971 Plymouth Roadrunner Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1971 Plymouth Roadrunner, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1971 Plymouth Roadrunner Drivetrains
Driveworks – Universal Joint (Part No.DW-316)
from
$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
Yukon Gear – Standard Open Spider Gear Replacement Kit For Dana 60 And 61 With 35 Spline Axles (Part No.16085)
from
$301.99
Yukon standard open spider gear replacement kit for Dana 60 and 61 with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Spider gear kit
- Fit Dana Spicer 60 open differential with 35 spline axles
- Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.
Yukon Gear – Dana 44 JK / 60 / 70U Pinion Nut Washer Replacement (Part No.33164)
from
$3.99
Product Features:
See More
- Pinion nut washer for Chrysler 7.25″, 8.25″, 8.75″ with 29 spline pinion, Jeep JK rear, Dana Spicer 60, 70, 70U and 70HD and 2007-2010 Ford 10.5″
Yukon Gear – Replacement Carrier Shim Kit For Dana 60, 70, 70HD, 70U & 80 (Part No.55011)
Yukon Gear – Replacement Baffle For Dana 60 & Dana 70-U (Part No.33001)
Yukon Gear – Bearing Race Driver (Part No.56017)
from
$215.99
Bearing race driver. No return.
Product Features:
See More
Product Features:
- Bearing race driver
- Fits HM89410 race
- All steel construction
Yukon Gear – Grizzly Locker For Dana 60, 4.56 & Up, 30 Spline (Part No.28004)
from
$1204.99
The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60 with 30 spline axles
- 4.56 and up ratio only
- Patented internal design reduces common locker failures
- 8620 internals for added strength
- Assembled in the USA
Yukon Gear – Dana 60, Dana 70 & Dana 80 Cover Bolt (Part No.33235)
from
$5.99
3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.
Product Features:
See More
Product Features:
- Cover bolt for Dana Spicer 60, 70 and 80
- 3/8″
Yukon Gear – Chrysler 8.75" "89" Housing Nodular Iron Drop Out Case (Part No.32052)
from
$564.99
89 housing nodular Iron Drop Out case, up to 500 HP, Billet adjuster for 8.75″ Chrysler. This dropout does not come with fill plug (Part number CHY612017).
Product Features:
See More
Product Features:
- Fits Chrysler 8.75″
- ’89’ case design
- Nodular iron for added strength
Yukon Gear – Replacement Trail Repair Kit For Dana 60 With 1310 Size U/Joint And U-Bolts (Part No.32282)
from
$251.99
Yukon replacement trail repair kit for Dana 60 with 1310 size U/joint and u-bolts. This kit comes with a yoke, U/joint, pinion seal, U/bolt or strap kit, pinion nut, and pinion nut washer (if applicable).
Product Features:
See More
Product Features:
- Fits Dana Spicer 60 and 70
- 1310 u-joint size
- Kit includes yoke, U-joint, pinion seal, pinion nut and washer, U-bolts and threadlocker
National – Shaft Repair Sleeve (Part No.99168)
from
$36.49
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
- Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
National – Bearings (Part No.M802011)
from
$14.79
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Dana 60 Pinion Gear Thrust Washer, Standard Open & Tracloc (Also 8.75" Chrysler Std) Dana 70 2Pc (Part No.33287)
from
$5.99
Dana 60 pinion gear Thrust washer, standard Open & TracLoc (also 8.75″ Chrysler STD) Dana 70 2PC.
Product Features:
See More
Product Features:
- Pinion gear thrust washer for Dana Spicer 60
- Fits standard open and Trac Loc applications
Yukon Gear – Dana 44 And Chrysler 9.25" Traclloc Clutch Kit Replacement (Part No.16153)
from
$139.99
Dana 44 & 9.25 Chrysler TracLoc clutch kit.
Product Features:
See More
Product Features:
- Clutch kit
- Fits Dana Spicer 44 and Chrysler 9.25″ Trac Loc positraction
Driveworks – Taper Bearing Cone (Part No.S-HM-88649)
from
$19.29
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Yukon Gear – Yoke For Chrysler 8.75" With 10 Spline Pinion And A 7260 U/Joint Size (Part No.41006)
from
$213.99
Yukon yoke for Chrysler 8.75″ with 10 spline pinion and a 7260 U/joint size. 2.125″ snap ring span, 1.078″ cap diameter. Inside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Chrysler 8.75″
- 10 spline
- 7260 u-joint size
- Inside snap ring design
- 2.125″ snap ring span
- 1.078″ cap diameter
- Strap style
Yukon Gear – 8.75" Chrysler Gasket (Part No.23001)
Yukon Gear – Crush Sleeve Eliminator Kit For Chrysler 8.75" (Part No.55039)
from
$86.99
8.75″ Chrysler 89 solid crush sleeve replacement spacer, preload. This item is compatible with ’89 case dropouts only.
Product Features:
See More
Product Features:
- Crush sleeve eliminator kit for Chrysler 8.75″ with ’89’ case housing
Yukon Gear – 1310 & 1330 U/Joint Strap, Dana 30, Dana 44, Model 35, & 9.25" With Bolts (Part No.41195)
from
$18.99
1310 & 1330 U/joint strap, Dana 30, Dana 44, Model 35, & 9.25″ w/bolts.
Product Features:
See More
Product Features:
- u-joint strap kit
- Fits Dana Spicer 30 and 44, AMC Model 35 and Chrysler 9.25″
- 1310 and 1330 u-joint size
- Includes two straps and four bolts
Yukon Gear – Carrier Installation Kit For Chrysler 9.25" Rear Differential (Part No.57001)
from
$173.99
Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Chrysler 9.25″ rear differential. This kit contains carrier bearings and races.
Product Features:
See More
Product Features:
- Fits Chrysler 9.25″ rear
- Includes carrier bearings and races
National – Bearings (Part No.M86610)
from
$9.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Dana 60 Semi-Float C-Clip (Part No.33247)
USA Standard Gear – Chrysler 8.25" Spartan Locker Cross Pin Shaft (Part No.17035)
from
$49.99
Product Features:
See More
- USA Standard Gear heavy-duty cross pin shaft
- Fits Chrylser 8.25″ with 27 and 29 spline axles
- Works with Spartan Locker or standard open spider gears
Yukon Gear – Six Piece Side Gear And Thrust Washer Kit For Chrysler 8" And 9.25" (Part No.33278)
from
$98.99
Six piece side gear thrust washer kit for Chrysler 8″ and 9.25″.
Product Features:
See More
Product Features:
- Side gear thrust washer kit
- Fits Chrysler 8″ and 9.25″
Motive Gear – Differential Pinion Seal (Part No.5126B)
from
$9.99
All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!
See More
Yukon Gear – Powr Lok Button Kit For Dana 30, Dana 44 & Chrysler 8.75" (Part No.33536)
from
$67.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t
Product Features:
See More
Product Features:
- Powr Lok button kit
- Fits Dana Spicer 30, 44 and Chrysler 8.75″
Yukon Gear – Chrysler 9.25" And Dana 44 / 60 Tracloc Clutch Guide Replacement (Part No.33249)
from
$8.99
Product Features:
See More
- Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
- For Trac Loc positraction applications only
Dorman – Differential Ring And Pinion Set (Part No.697-356)
from
$291.99
This differential ring and pinion directly replaces the original equipment on specific vehicle years, makes and models.
Product Features:
See More
Product Features:
- Direct replacement – this ring and pinion set matches the fit and function of the original components on certain vehicle applications
- Effective fix – eliminates grinding and whining from failed original bearings
- Thoroughly tested – vehicle try-on testing and rigorous quality control measures ensure longevity
- Trustworthy quality – backed by team of designers and engineers in the United States
Popular 1971 Plymouth Roadrunner Drivetrains Categories
1971 Plymouth Roadrunner Drivetrains
You count on your 1971 Plymouth Roadrunner to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 380 Drivetrains ranging in price from $2.49 to $1,487.99, you’re sure to find everything you need for your 1971 Plymouth Roadrunner.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 16 different brands like Valvoline, Driveworks, and National. 1971 Plymouth Roadrunner Drivetrains start as low as $2.49!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 5,941 extensive product reviews on 1971 Plymouth Roadrunner Drivetrains. Some of the top-rated Drivetrains products we carry are Multi Purpose Seal with 4.6 stars and Axle Repair Bearing with 3.6 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1971 Plymouth Roadrunner below to get started!
Top-Rated Drivetrains Brands For Your 1971 Plymouth Roadrunner
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1971 Plymouth Roadrunner running right for years to come. In our inventory you’ll find brands like Valvoline, Driveworks, National, and even more.
Popular Dorman Drivetrains
You’ll find popular Dorman brand products across Spindles. All are waiting to get your 1971 Plymouth Roadrunner back on the road. Some of the top-rated Dorman products in these categories are:
from
$4.99
(3)
Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm
Spindle Retainers
Top-Rated Drivetrains
If are what you’re looking for, our inventory holds plenty. We stock brand Drivetrains for your 1971 Plymouth Roadrunner, and some of our most reviewed parts include:
from
$12.79
(446)
MaxLife Multi-Vehicle (ATF) Full Synthetic Automatic Transmission Fluid, 1 Quart
Differential Oil
FAQs for 1971 Plymouth Roadrunner Drivetrains
What are the most purchased Drivetrains for the 1971 Plymouth Roadrunner?
Out of 380 Drivetrains for the 1971 Plymouth Roadrunner, the most popular in our inventory are:
What are the top-rated 1971 Plymouth Roadrunner Drivetrains?
Top-rated Drivetrains for your 1971 Plymouth Roadrunner based on customer reviews/ratings are:
from
$16.49
(19)
Axle Repair Bearing
“Up and running again with no more axle seal leaks in my Grand Marquis with 318k miles on it!”
from
$13.99
(14)
Tapered Cone/Cup Wheel Bearing Set
“Advance Auto website when entering my 1989 Ford F150 doesn’t ask if it is 2 wheel or 4 wheel drive. So I had to return the first set”
