from

$749.99

High burst strength woven lining to withstand heat and higher engine RPM. Heavy-duty sprung hub assembly to allow smooth engagement and steady torque transfer without chatter. Recommended for high horsepower street vehicles in addition to occasional drag strip use.

Product Features:

Built As Matched Assembly
Exceptional Performance
Exceptional Durability
Long Term Dependability

from

$141.99

These ACCEL wire sets are custom tailored for race engines and their builders. The oversize 8.8 mm wire is rated for 600 degrees Fahrenheit and 60kV. Resists heat, chemicals and moisture. High density insulation eliminates arcing. Route over and under headers.

Product Features:

150 Ohms Per Foot
8.8mm Oversize Silicone Jacket

from

$92.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets
Not for OEM Hydraulic Roller-Lifter Camshaft Eng.

from

$25.99

This Spectre Alternator Bracket Kit is a two piece set designed to fit Chrysler 318-340-360 small block engines. Featuring a triple chrome-plated finish and high quality steel construction, this kit is an OEM replacement that includes two pieces.

Product Features:

Fits small block Chrysler 318-340-360 engines
Manufactured from high quality steel
Kit includes two pieces
Features a triple chrome-plated finish
Factory replacement

from

$1243.99

Designed for carburetor V8 engines. Power increases from 200 to 400 horsepower. Simple to install. Shorter spray bars. More even distribution across the plenum. A more balanced air and fuel ratio. Quicker response time.

Product Features:

Designed For Carbureted V8 Engines
Power Increases From 200-400_ HP
Simple To Install
Shorter Spray Bars
More Even Distribution Across The Plenum
A More Balanced Air/Fuel ratio
Quicker Response Time

from

$259.99

The B&M Unimatic is an ideal replacement for column shift vehicles, includes neutral safety switch, 5 foot cable and a boot and plate.

Product Features:

Ideal As Column Shift Replacement
Includes Neutral Safety Switch
Includes Black T-Handle
Backup Light Not Available
Includes 5 ft. Cable and Hardware
Includes Boot and Plate

from

$426.99

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in

Product Features:

Maximum Cooling for Street and Racing Engines
Internal Passages Are Balanced for Maximum Flow
Impeller is Larger than Others For Max Pressure
Impeller Vanes Dramatically Increase Flow Rates
Equal Distribution to Both Sides of Block
Only Flows in One-Direction for Optimum Efficiency

from

$79.99

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

More Accurate Ignition Timing
Improves Performance
Provides More Accurate Ignition Timing
Easy To Install w/Hand Tools
Reduced Maintenance
Thermal Clad Based Surface Mount Construction
Utilizes Specialized Electronic Circuitry
Ignition Timing Is Stable From 1 To 10000rpm

from

$55.99

When you change a cam, you don’t need a complete engine gasket set, because you don’t have to take everything apart. Mr. Gasket cam change gasket sets are tailored to deliver just the pieces that you need when you swap bump-sticks. They include gaskets for the valve covers, intake manifold, oil pan, water pump, timing-chain cover, and fuel pump.

Product Features:

Comes with all gaskets
Fuel injector oring not included
Meets performance standards

from

$482.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 deg. Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used

from

$71.99

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

Improved output coil for electronic ignitions
Works w/Blaster Ignition Or MSD 5/6/7 Series
Ballast Resistor Required If Used w/Stock Points Ignition
Alkyd tower w/high dielectric properties lessens carbon tracking

from

$17.29

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$819.99

Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:

Long Tube Lengths
Long Transition Collectors
Monstrous Low-Mid Range Torque
Keep Top End Horsepower
Provides Finest Fit
Most Durable Design Available

from

$37.99

Spectre’s High Performance Replacement Air Filters are engineered to outperform ordinary paper filters by providing increased air flow for improved performance. Manufactured using high quality materials including pre-dyed synthetic media, urethane, and steel mesh, this performance air filter is factory pre-oiled and ready to use.

Product Features:

High performance and high air flow filter
Filter media is non-woven synthetic and pre-dyed
Replaces stock air filter
Easy to install with no special tools or skills required
Reinforced with a steel mesh

from

$125.99

Kits include most popular chrome dress-up components, including short, OEM height valve covers with integral oil baffles.

Product Features:

Includes oil baffles
Chrome plated

from

$48.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$44.99

Product Features:

0.1875 in. Thickness
Core-Reinforced-Composite Material
For Late Model 1963-1980 BB Chrysler W/ 6-Bolt Valve Covers
Set of 2
Made In The USA

from

$43.49

This Spectre Timing Cover Kit is designed to protect components like timing gears and the chain or belt. It featurings triple chrome plated steel construction. Timing cover kits are engineered for optimum fit and function.

Product Features:

Triple chrome plated
Steel construction
OEM replacement
OEM fit & function

from

$36.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$264.99

Product Features:

CHRY 9BLT 8.75 LATE R/P 4.56 MGP

from

$357.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$840.99

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some Holeshots.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$25.99

Product Features:

Service Part
Makes Connections Quick And Easy

from

$449.99

MSD Pro-Billet Distributors are the finest performance and racing distributors available. Every feature has been engineered to endure the rigors of high performance and racing engines. Whether cruising the streets or racing stock cars, dragsters, boats or trucks, MSD has a distributor for it. MSD uses state-of-the-art, Computer Numerical Controlled (CNC) mills and lathes to machine each housing. After a long series of precise cuts and movements, the billet is formed into a flawless distributor housing that is accurate to within 0.001″. The flex-free housings are lightweight, have no porosity or weak areas and look great on polished, show quality engines.

Product Features:

Smaller diameter CNC machined billet aluminum housing
Billet aluminum base clears aftermarket heads and valve covers
Must Be Used w/An MSD Ignition Control
Supplied w/small dia. cap w/HEI style terminals; race and rotor
Will accept PN[8441] Cap-A-Dapt
Mechanical advance assembly can be locked out for crank trigger systems
Advance weight pins are staked and tig welded to the plate
Nylon pads ensure smooth operation of the advance weights

from

$41.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$47.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$165.99

This Spectre Oil Pan was designed for the big block Chrysler/Dodge/Plymouth 383, 400, 413, 426, & 440 engines. This triple chrome plated oil pan is made to replace the oem oil pan.

Product Features:

Triple chrome-plated
Steel construction
Stock capacity
Made from high quality material

from

$2198.99

The Edelbrock #5093 E-Street cylinder heads are designed for use with 1961-1979 Chrysler 361-440 c.i.d. Wedge engine applications. The Edelbrock E-Street cylinder heads offer American made quality and affordable performance. E-Street cylinder heads featur

Product Features: