1971 Mercury Cougar Drivetrains
Find Your Specific 1971 Mercury Cougar Drivetrains
Below you will find various in-demand Mercury Drivetrains, components and accessories for your 1971 Cougar. Advance Auto Parts has popular Cougar parts like Drive Shafts and Axles, Transfer Cases, Universal Joints and more. You’ll also find aftermarket and OEM Drivetrains for other Cougar model years including
1993,
1994,
1995,
1996,
1997,
1999,
2000,
2001,
2002 and more. Select a category of 1971 Mercury Cougar Drivetrains below and start saving instantly.
Popular 1971 Mercury Cougar Drivetrains Categories
Essential Drivetrains for 1971 Mercury Cougars
Yukon Gear – 9" Ford Gasket (Part No.23012)
Yukon Gear – Star Washers, 3.250" Ford 9" Drop Out New Design Only (Part No.32144)
from
$4.99
STAR washers, 3.250″ Yukon Ford 9″ Drop Out new design ONLY.
Product Features:
See More
Product Features:
- Star washer
- Fits Ford 9″
- 3.250″ designs only
Yukon Gear – Preload Shim Kit For Chrysler 8.75" & Ford 9" (Part No.55030)
from
$21.99
8.75″ Chrysler & 9″ Ford preload shim kit.
Product Features:
See More
Product Features:
- Preload shim kit for Ford 9″ and Chrysler 8.75″ with ’41’ and ’42’ case housing
USA Standard Gear – Standard Spider Gear Set For Ford 7.5" (Part No.39014)
from
$156.99
Spindle nut washer for Dana 28, ’92 & down. This replaces Spicer part number 40075.
Product Features:
See More
Product Features:
- Spider gear kit
- Fit Ford 7.5″ open differential
- Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
Yukon Gear – Pinion Install Kit For Ford 8.8" Differential (Part No.13041)
from
$167.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.
Product Features:
See More
Product Features:
- Fits 2009 and down Ford 8.8″
- Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.
Yukon Gear – Outer Oil Slinger For Ford 7.5", 8.8", 9", 10.25" (Part No.33022)
from
$8.99
Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.
Product Features:
See More
Product Features:
- Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear
Motive Gear – Differential Crush Sleeve (Part No.3507575)
Yukon Gear – 8" Ford O-Ring (Part No.30027)
Yukon Gear – Fill Plug For Ford 9", 1/2" Thread (Part No.33539)
from
$10.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t
Product Features:
See More
Product Features:
- Fill plug
- Fits Ford 9″
Yukon Gear – Outer Axle Seal For 8" Ford (Part No.30031)
from
$43.99
Outer axle seal for 8″ Ford.Yukon Mighty seal.
Product Features:
See More
Product Features:
- Outer axle seal
- Fits Ford 8″
Yukon Gear – Trao Loc Spring For Ford 8.8", 28 Spline (Part No.33515)
Powertrax – Grip LOK Traction System (Part No.LK109028)
from
$668.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!
See More
Yukon Gear – The Carrier Bearing Puller (Part No.56072)
from
$883.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.
Product Features:
See More
Product Features:
- Carrier bearing puller
- Works with an impact gun to safely and easliy remove carrrier bearings
Yukon Gear – Bearing Race Driver Set, 21 Piece (Part No.56030)
from
$1566.99
21 Piece bearing race driver set. (Box wt: 140lbs) No return.
Product Features:
See More
Product Features:
- Bearing race driver set
- 21 pieces
- All steel construction
Yukon Gear – Trac Loc For Ford 9" Wtih 31 Spline Axles – Street Design (Part No.26010)
from
$789.99
The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Ford 9″ with 31 spline axles
- Trac Loc positraction
- Clutch style positraction
- Street design
- Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
- Fully rebuildable
- Assembled in the USA
Yukon Gear – Extra HD 3.250" Nodular Iron Dropout For Ford 9" With Load Bolt (Part No.32151)
from
$877.99
Yukon Extra HD 3.250″ nodular Iron dropout for Ford 9″ with load bolt. Yukon nodular iron dropouts feature a 5/8″ cap bolt and forged caps for maximum strength. Load bolt design prevents gear deflection under heavy loads. Rated up to 1400HP!
Product Features:
See More
Product Features:
- Fits Ford 9″
- 3.250″ carrier race diameter
- Nodular iron for added strength
- Load-bolt design reduces ring gear deflection under high horsepower
Yukon Gear – Pinion Support Bolt For 8" And 9" Ford (Part No.33242)
from
$6.99
Pinion support bolt for 8″ and 9″ Ford.
Product Features:
See More
Product Features:
- Pinion support bolt for Ford 8″ and 9″
- 3/8″ x 24 thread
- 1.0″ long
Yukon Gear – Pinion Gear And Thrust Washer (0.750" Shaft) For 8.8" Ford (Part No.33297)
from
$8.99
Pinion gear thrust washer (0.750″ shaft) for 8.8″ Ford.
Product Features:
See More
Product Features:
- Pinion gear thrust washer
- Fits Ford 8.8″
- 0.750″ I.D.
Motive Gear – Differential Carrier Gear Kit (Part No.F7.5BI)
Yukon Gear – Purple Aluminum Pinion Support For 9" Ford Daytona (Part No.32036)
from
$264.99
Product Features:
See More
- Fits Ford 9″ with 28 spline pinion
- Larger inner pinion bearing reduces gear deflection under high load
- Races installed
- 6061 aluminum
- Annodized purple
Yukon Gear – Adaptor Washer For 28 Spline Pinion In Oversize Support, For 9" Ford (Part No.32240)
from
$71.99
Adaptor washer for 28 spline pinion in oversize support, for 9″ Ford.
Product Features:
See More
Product Features:
- Adapter washer
- Fits Ford 9″
- Adapts 28 spline pinion into 35 spline pinion support
Spicer – Universal Joint (Part No.5-1310X)
from
$38.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More
ARP Auto Racing – For Use With Ford 8.8 And 9" Using 3/4"Socket, 0.75"L Under Head, 7/16"-20 (Part No.250-3003)
from
$43.99
The tremendous shock loads generated at launch by most any drag racing vehicle equipped with today sticky tire compounds or the acceleration and deceleration of oval track cars put considerable strain on the ring gear. For this reason, the fastener experts at ARP have developed the Pro Series ring gear bolts. they are forged from premium grade 8740 chrome moly steel and are heat treated to a nominal rating of 200,000 PSI tensile strength. Specially hardened, precision ground washers are included where required. Available to fit most any ring gear setup ranging from popular 9 Inch Ford GM 10 and 12 bolt rear ends to the beefy strange differentials found in top fuel and funny car applications.
Product Features:
See More
Product Features:
- Forged From Premium Grade 8740 Chrome Moly Steel
- Heat Treated
- Nominally Rated At 200,000 Psi Tensile Strength
- Specially Hardened, Precision Ground Washers
- 0.75″ Underhead Length
- 200,000 PSI
- Sold As A Set
National – Shaft Repair Sleeve (Part No.99199)
from
$37.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
Dorman – Spindle Washer – I.D. 3/4 In. O.D. 1-21/32 In. Thickness 3/32 In. (Part No.618-005.1)
from
$3.99
This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Powertrax – No-Slip Traction System (Part No.9206902800)
from
$551.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles. Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction. Powertrax® = Extreme Traction Systems!
See More
Felpro – Differential Carrier Gasket Oval Shaped 10 Bolt Hole Gasket (Part No.RDS 13270)
from
$5.49
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for the repair environment
- Unsurpassed quality you can trust
- Includes all parts needed to complete the repair
Driveworks – Taper Bearing Cone (Part No.S-LM-102949)
from
$15.49
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Upgrade your 1971 Mercury Cougar with Top-Quality Drivetrains
When it comes to maintaining or upgrading your 1971 Mercury Cougar, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Mercury or enhancing its overall performance, Drivetrains are key to keeping your Cougar functioning at its best. At Advance Auto Parts, we offer a wide selection of 375 Drivetrains for the 1971 Mercury Cougar, designed to meet your needs without breaking the bank.
From
Drive Shafts and Axle
replacements to
Transfer Cases
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1971 Mercury Cougar at great prices.
Our Drivetrains inventory for this model
ranges from just $1.99 to $1,566.99, with
an average price of $231.10.
Our 375 Drivetrains in stock come from 17 trusted brands, so you’re sure to find the right part for your 1971 Mercury Cougar without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1971 Mercury Cougar, we stock popular OEM and aftermarket Drivetrains from top names
like Spicer, Moog, National, and more.
Spicer Drivetrains
start at just $31.99 and boast an impressive 4.6 stars average rating from customers.
Moog and National also bring quality to the table, with Drivetrains available starting at $11.99, and at an average 4.5 stars rating.
With 5,187 customer reviews and counting, our 1971 Mercury Cougar Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants
and more to make sure your 1971 Mercury Cougar is always ready to roll. We’re committed to providing you with everything you need to keep your Cougar in top shape, all in one place.
Start shopping confidently below for your 1971 Mercury Cougar!
Best-Selling Drive Shafts and Axles for 1971 Mercury Cougars
Enhance the driving experience in your Mercury with 12 quality Drive Shafts and Axle components, starting at $5.99.
Spicer – Universal Joint (Part No.5-1310X)
from
$38.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More
Yukon Gear – Ford 7.5", 8", 8.8", & 9" Axle Stud (Part No.33175)
from
$6.99
Ford 7.5″, 8″, 8.8″, & 9″ axle stud.
Product Features:
See More
Product Features:
- Axle stud for Ford 7.5″, 8.8″ and 9″
- 1/2″ x 20 thread
- 1 7/8″ long
- 29/64″ shoulder length
Yukon Gear – 9" 31Spline (69-73Mustang & Others) Axle Seal (Part No.30211)
from
$16.99
9″ 31spline (69-73Mustang & OTHERS) axle seal (1.5″ shaft).Yukon Mighty seal.
Product Features:
See More
Product Features:
- Rear axle seal
- Fits 1969-1973 Ford Mustang with Ford 9″
Yukon Gear – Mighty Seal (Part No.30214)
from
$26.99
Axle seal.Yukon Mighty seal.
Product Features:
See More
Product Features:
- Rear axle seal
- Fits Ford 8″
- 2.264″ O.D.
- 1.365″ I.D.
Yukon Gear – Fill Plug For Ford 9", 1/2" Thread (Part No.33539)
from
$10.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t
Product Features:
See More
Product Features:
- Fill plug
- Fits Ford 9″
Yukon Gear – Axle Bearing Retainer For Ford 9", Large Bearing, 1/2" Bolt Holes (Part No.33467)
from
$67.99
Product Features:
See More
- Axle bearing retainer for Ford 9″
- Fits large bearing applications
- 1/2″ bolt holes
- 3 1/2″ x 2 3/8″ bolt pattern
Yukon Gear – Ford 9" (3/8" Holes) Torino Design Housing Ends (Part No.32160)
from
$279.99
9″ (3/8″ holes) Torino design housing ends for Ford (for 2-5/8″ ID axle tube).
Product Features:
See More
Product Features:
- Housing ends
- Fits Ford 9″
- 3 9/16″ x 2″ bolt pattern
- 3/8″ bolt holes
- Set of two
Yukon Gear – Conversion Bearing For Small Bearing Ford 9" Axle In Large Bearing Housing (Part No.18046)
from
$92.99
Conversion bearing for small bearing Ford 9″ axle in large bearing housing.
Product Features:
See More
Product Features:
- Axle bearing
- Fits Ford 9″
- Conversion bearing to install small bearing axle into large bearing housing
- 3.150″ O.D.
- 1.377″ I.D.
Yukon Gear – Adaptor Washer For 28 Spline Pinion In Oversize Support, For 9" Ford (Part No.32240)
from
$71.99
Adaptor washer for 28 spline pinion in oversize support, for 9″ Ford.
Product Features:
See More
Product Features:
- Adapter washer
- Fits Ford 9″
- Adapts 28 spline pinion into 35 spline pinion support
Yukon Gear – Axle Bearing Retainer For Ford 9", Large & Small Bearing, 3/8" Bolt Holes (Part No.33466)
from
$22.99
Product Features:
See More
- Axle bearing retainer for Ford 9″
- Fits large and small bearing applications
- 3/8″ bolt holes
- 3 9/16″ x 2″ bolt pattern
Yukon Gear – Axle Bearing Retainer For Ford 9", Small Bearing, 3/8" Bolt Holes (Part No.33468)
from
$22.99
Product Features:
See More
- Axle bearing retainer for Ford 9″
- Fits small bearing applications
- 3/8″ bolt holes
- 3 5/16″ x 2″ bolt pattern
Yukon Gear – Model 20 & Model 35 Axle Stud 1/2"-20 X 1.625" Length, 0.620" Dia – Knurl (Part No.33181)
from
$5.99
Model 20 & Model 35 axle stud 0.620″ Dia. Shank.
Product Features:
See More
Product Features:
- Axle stud for AMC Model 20 and Model 35
- 1/2″ x 20 thread
- 0.620″ knurl diameter
- 1.625″ long
Most Popular 1971 Mercury Cougar Transfer Cases
Customize your Mercury with 5 Transfer Cases products
like Input Shaft Bearings,
Input Shaft Seals, and
Mounting Adapter Seals, all
priced under $43.99.
National – Bearing (Part No.M88048)
from
$15.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
- OE-STYLE DESIGN — Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on
National – Shaft Repair Sleeve (Part No.99199)
from
$37.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
Driveworks – Oil Seal (Part No.S-3638)
National – Multi-Purpose Bearing (Part No.307-L)
from
$43.99
Product Features:
See More
- BUILT TO LAST: Advanced heat treatment process for strength
- PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
- RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
- COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Schaeffler – Cup (Part No.M88010)
from
$11.29
With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.
Product Features:
See More
Product Features:
- High-precision and High-quality components used in all KITs
- Coverage of classic and new high-tech solutions for the best system coverage
Top Picks for 1971 Mercury Cougar Universal Joints
Upgrade Mercury Cougars with top-quality Universal Joints parts, including 38 OEM and aftermarket selections for your 1971 model.
Spicer – Universal Joint, Greaseable 1310 Series OSR (Part No.5-153X)
from
$31.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.
Product Features:
See More
Product Features:
- OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
- Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
- The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
- Zerk allows for lubricating at regular intervals to help extend the life of the part.
Spicer – Universal Joint, Greaseable 1330 Series OSR (Part No.5-213X)
from
$42.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.
Product Features:
See More
Product Features:
- OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
- Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
- The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
- Zerk allows for lubricating at regular intervals to help extend the life of the part.
MOOG Driveline Products – Universal Joint U-Bolt Kit (Part No.534-10)
from
$11.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.
Product Features:
See More
Product Features:
- For U-Joints 375, 430, 434 & 498
- Fits 1-1/8″ bearings
MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.354)
from
$34.99
Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
Product Features:
See More
Product Features:
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- GREASEABLE DESIGN – Greaseable u-joints allow for new grease to flush out contaminants and moisture
- KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
- Cross forging shape and flash provide easier installation and high strength
MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.369)
from
$35.99
Product Features:
See More
- BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
- STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
- INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
- RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
Driveworks – Universal Joint (Part No.DW-354)
from
$31.99
Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.254)
from
$23.99
Product Features:
See More
- BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.269)
from
$33.99
Product Features:
See More
- BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.280)
from
$41.49
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
Product Features:
See More
Product Features:
- BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
- GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Driveworks – Universal Joint (Part No.DW-434)
from
$16.49
Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
Driveworks – Universal Joint (Part No.DW-369)
from
$15.99
Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.270)
from
$39.99
Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
Product Features:
See More
Product Features:
- BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
- GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.434)
from
$25.99
Product Features:
See More
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
- KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
- Cross forging shape and flash provide easier installation and high strength
Dorman – Help – U-Joint Bolt Kit (Part No.81004)
from
$6.99
This universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.
Product Features:
See More
Product Features:
- Direct replacement – this universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles
- Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
- Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Neapco – Universal Joint (Part No.2-4801)
Neapco – Universal Joint (Part No.2-4800)
MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.430)
from
$27.99
Product Features:
See More
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
- KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
- Cross forging shape and flash provide easier installation and high strength
Driveworks – Universal Joint (Part No.DW-270)
from
$15.99
Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
Spicer – Universal Joint (Part No.5-1330X)
from
$40.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More
MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.265)
from
$38.99
Backed by superior materials and rigorous testing, MOOG Super Strength® universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
Product Features:
See More
Product Features:
- BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
- GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Spicer – Universal Joint, Greaseable 1330-F Spec Series (Part No.5-1204X)
from
$36.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.
Product Features:
See More
Product Features:
- OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
- Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
- The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
- Zerk allows for lubricating at regular intervals to help extend the life of the part.
Spicer – Universal Joint (Part No.5-7438X)
from
$45.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More
Yukon Gear – 1310 U/Joint With Zerk Fitting On Cross (Part No.42008)
from
$44.99
Yukon 1310 U/Joint with zerk fitting on cross. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring.
See More
MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.264)
from
$38.99
Product Features:
See More
- BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
- COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
- CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
- KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
- STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
In-Demand Differentials for 1971 Mercury Cougars
Select from 315 premium Differentials parts for your 1971 Mercury Cougar, with prices ranging from $1.99 to $1,566.99.
Felpro – Differential Carrier Gasket Oval Shaped 10 Bolt Hole Gasket (Part No.RDS 55074)
from
$9.99
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
National – Multi-Purpose Seal (Part No.8181NA)
from
$12.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Design type: spring loaded; multi-lip
- Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
- Good low temperature capability
- Low swell in hydrocarbon fluids
- Delivers quality and reliable performance for every type of repair
Powertrax – No-Slip Traction System (Part No.9206902800)
from
$551.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.Powertrax® = Extreme Traction Systems!
See More
Motive Gear – Differential Pinion Nut (Part No.379570S)
from
$6.99
All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!
See More
Driveworks – Taper Bearing Cone (Part No.S-LM-102949)
from
$15.49
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Yukon Gear – 3 Qt – 80W90 Conventional Gear Oil With Posi Additive (Part No.15003)
from
$57.99
3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.
Product Features:
See More
Product Features:
- Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive
Yukon Gear – 3 Qt – Penzoil 80W90 Conventional Gear Oil (Part No.15002)
from
$44.99
3 Qt. Penzoil 80W90 conventional gear Oil.
Product Features:
See More
Product Features:
- Includes three quarts of conventional oil
Dorman – Help – Pinion Crush Sleeves (Part No.81056)
from
$6.49
This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles
- Required replacement – when servicing the differential
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
National – Bearing Race (Part No.M86610)
from
$9.99
Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Felpro – Differential Carrier Gasket Oval Shaped 10 Bolt Hole Gasket (Part No.RDS 13270)
from
$5.49
Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered and manufactured specifically for the repair environment
- Unsurpassed quality you can trust
- Includes all parts needed to complete the repair
Yukon Gear – Crush Sleeve (Part No.33085)
from
$9.99
Crush Sleeve for Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9 3/8″, 9″ & 9.75″. .480″ long.
Product Features:
See More
Product Features:
- Crush sleeve for AMC Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9″ and 9.75″
- 0.480″ tall
Yukon Gear – Outer Oil Slinger For Ford 7.5", 8.8", 9", 10.25" (Part No.33022)
from
$8.99
Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.
Product Features:
See More
Product Features:
- Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear
Yukon Gear – Ford 8" & 9" Standard Open, Ag, & Detroit Locker Ring Gear Bolt (Part No.33058)
from
$5.99
Ford 8″ & 9″ standard Open, AG, & Detroit locker ring gear bolt. 7/16″ head, .925″ long.
Product Features:
See More
Product Features:
- Ring gear bolt for Ford 8″ and 9″
- For use with standard open carrier, Auburn Gear limited slip and Detroit Locker
- 7/16″ head
- .925″ long
Yukon Gear – Ford 8" & 9" Standard Open, Ag, & Detroit Locker Ring Gear Bolt (Part No.33043)
from
$5.99
Ford 8″ & 9″ standard Open, AG, & Detroit locker ring gear bolt, 1.0″ long, Ford.
Product Features:
See More
Product Features:
- Ring gear bolt for Ford 8″ and 9″
- For use with standard open carrier, Auburn Gear limited slip and Detroit Locker
- 1.0″ long
Yukon Gear – Ford 8" & 9" Tracloc Ring Gear Bolt (Part No.33044)
from
$4.99
Ford 8″ & 9″ TracLoc ring gear bolt, 1-1/4″ long.
Product Features:
See More
Product Features:
- Ring gear bolt for Ford 8″ and 9″
- For use with Trac Loc limited slip
- 1.25″ long
Motive Gear – Ring Gear Bolt (Part No.D8OZ4216B)
Yukon Gear – Pinion Nut (Part No.33154)
from
$7.99
Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.
Product Features:
See More
Product Features:
- Pinion nut for Ford 7.5″, 8″ and 9″
- 3/4″ x 20 thread
- 1 1/6″ socket
Yukon Gear – 9" Ford Gasket (Part No.23012)
Yukon Gear – Redline Synthetic "Shock Proof" Oil With Positraction Additive – 4 Quarts (Part No.15005)
from
$148.99
Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.
Product Features:
See More
Product Features:
- Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive
Yukon Gear – Preload Shim Kit For Chrysler 8.75" & Ford 9" (Part No.55030)
from
$21.99
8.75″ Chrysler & 9″ Ford preload shim kit.
Product Features:
See More
Product Features:
- Preload shim kit for Ford 9″ and Chrysler 8.75″ with ’41’ and ’42’ case housing
Mr. Gasket – Rear End Gasket – Ford 9" – Blend Of Nitrile Rubber And Fiber For Excellent Sealing And Durability (Part No.82)
from
$25.99
Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit. Fits 1957-1981 Ford 10 bolt 9 inch ring gear.
Product Features:
See More
Product Features:
- .047″ thick cellulose/nitrile composite gasket material
- Precision die cut
- Reusable
Yukon Gear – Dana 44, Ford 8" / 9", And Model 20 Side Gear Thrust Washer Replacement (Part No.33283)
from
$5.99
Product Features:
See More
- Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
- 0.030″ thick
Yukon Gear – Redline Synthetic "Shock Proof" Oil – 3 Quarts (Part No.15000)
from
$99.99
Redline Synthetic “Shock Proof” Oil. 3 Quarts.
Product Features:
See More
Product Features:
- Includes three quarts of Redline Shockproof oil
Yukon Gear – Pilot Bearing For Ford 9" (Part No.18042)
from
$38.99
8.6″ GM 99-08 PINION Bearing & SEAL KIT .
Product Features:
See More
Product Features:
- Pilot bearing
- Fits Ford 9″
- 0.656″ thick
Most Sold 1971 Mercury Cougar Spindles
Explore our best-selling Mercury parts for the 1971 Cougar among 5 OEM and aftermarket options starting from $2.99.
Dorman – Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In. (Part No.615-075.1)
from
$3.49
This spindle nut retainer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Dorman – Standard Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In. (sold by each) (Part No.615-074)
from
$4.49
This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Dorman – Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In. (Sold by each) (Part No.615-075)
from
$6.99
This spindle nut retainer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
- Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Dorman – Spindle Washer – I.D. 13/16 In. O.D. 1-21/32 In. Thickness 3/32 In. (Part No.618-013.1)
from
$4.99
This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Dorman – Spindle Washer – I.D. 13/16 In. O.D. 1-21/32 In. Thickness 3/32 In. (Sold by each) (Part No.618-013)
from
$2.99
This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.
Product Features:
See More
Product Features:
- Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
- Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
- Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Top-Rated Drivetrains Brands For Your 1971 Mercury Cougar
Shop for the best-rated brands offering Drivetrains and other products for your 1971 Mercury Cougars. Below you’ll find some of our best rated Drivetrains from Spicer, Moog, and National, and more. Drivetrains from these brands that fit a 1971 Cougar start at just $11.99 and are rated as high as 4.6 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.
Popular Spicer 1971 Mercury Cougar Drivetrains
When it comes to maintaining or upgrading your 1971 Mercury Cougar, using quality Drivetrains is essential to ensure durability and a perfect fit. Spicer ticks all of those boxes. We offer a wide selection of Spicer Drivetrains, specifically designed for the 1971 Mercury Cougar. With over 3 Spicer brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $31.99, with an average price of just $37.99. Plus, with over 19 customer reviews and an average rating of 4.6 stars, you can trust that our Spicer Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
from
$42.99
(5)
Universal Joint, Greaseable 1330 Series OSR
“I changed my Ford Expedition’s stock non greaseable universal joints at 213K miles. There was noticeable vibration. The Spicers fit well and have t”
from
$31.99
(12)
Universal Joint, Greaseable 1310 Series OSR
“No problems with Installation and appears to be quality part! Great for my old School Street Car!”
from
$38.99
(2)
Universal Joint
“I use this on a 4×4 off-road. It’s always a tough trade-off between the greaseable and non-greasable u-joints. The non-greaseable is stronger. The”
Popular Moog 1971 Mercury Cougar Drivetrains
Moog auto parts is one of the highest quality Drivetrain brands in the market. Any 1971 Mercury Cougar owner should feel confident when installing genuine Moog parts in their vehicle. To ensure the best fit and performance for your 1971 Cougar, Advance Auto Parts carries a full inventory of 3 Moog Drivetrains. Plus you will be keeping your Mercury in peak condition while saving money because prices on these Moog Drivetrains range from $11.99 to $35.99, plus, with more than 227 customer reviews and an impressive 4.5 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.
from
$35.99
(82)
Greaseable Premium Universal Joint
“Great u joints works very well I’ll recomended”
FAQs for 1971 Mercury Cougar Drivetrains
Which Drivetrains are best-sellers for 1971 Mercury Cougars?
Out of 375 Drivetrains that fit 1971 Mercury Cougars, the following parts are the top sellers:
- Universal Joint (10265714) – $15.99
- Universal Joint (10265720) – $31.99
- Non-Greaseable Super Strength Universal Joint (10087058) – $23.99
What’s the price range for 1971 Mercury Cougar Drivetrains?
Drivetrain prices for the 1971 Mercury Cougar start at $1.99 and go up to $1,566.99 for the most premium parts.
What’s the average price of a Drivetrain for a 1971 Mercury Cougar?
The average price for Drivetrains for the 1971 Mercury Cougar is $231.10. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Drivetrains for other Mercury Cougar model years?
What are the cheapest Drivetrains for my 1971 Mercury Cougar?
The cheapest 1971 Mercury Cougar Drivetrains we carry in stock are:
- Ring Gear Bolt (19640279) – $1.99
- Differential Crush Sleeve (10592883) – $2.99
- Differential Crush Sleeve (10282338) – $2.99
- Spindle Washer – I.D. 13/16 In. O.D. 1-21/32 In. Thickness 3/32 In. (Sold by each) (22148784) – $2.99
- Spindle Nut 13/16 In.-20 Hex Size 1-1/8 In. (21260549) – $3.49
What are the top-rated Drivetrains that fit the 1971 Mercury Cougar?
Out of 5,187 reviews by customers, our 1971 Mercury Cougar Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1971 Mercury Cougar and their top-rated products:
- Differentials
- No-Slip Traction System (10461097) – $551.99
- Multi-Purpose Seal (18445017) – $12.99
- Differential Carrier Gasket Oval Shaped 10 Bolt Hole Gasket (5185890) – $9.99
- Universal Joints
- No-Slip Traction System (10461097) – $551.99
- Multi-Purpose Seal (18445017) – $12.99
- Differential Carrier Gasket Oval Shaped 10 Bolt Hole Gasket (5185890) – $9.99
What types of Drivetrains do you sell for my 1971 Mercury Cougar?
As of 3/1/26, these are some of the most in-demand types of Drivetrains for a 1971 Mercury Cougar:
Can I get help with 1971 Mercury Cougar Drivetrain orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Mercury Drivetrains and more.
What is your return policy for Mercury Cougar Drivetrains?
Advance Auto Parts keeps returns simple. For new Mercury Cougar Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
