1971 Dodge Dart Differentials

Product Features:

• O-ring for seal housing
• Fits Dana Spicer 60

Yukon standard open spider gear kit for ’96 and older 8.25″ Chrysler with 27 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Chrysler 8.25″ open differntial with 27 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Dana 60 pinion gear Thrust washer, standard Open & TracLoc (also 8.75″ Chrysler STD) Dana 70 2PC.

Product Features:

• Pinion gear thrust washer for Dana Spicer 60
• Fits standard open and Trac Loc applications

8.25″ Chrysler notched cross pin shaft for standard open carriers. (0.801″ diameter). This cross pin shaft is not compatible with Powertrax Lock Rights or Spartan Lockers, or with factory Trac Loc positractions.

Product Features:

• Cross pin shaft
• Fits Chryler 8.25″
• 0.801″ diameter
• Notched
• Not compatible with Spartan Lockers or Lock Rights

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

• Seal housing for Dana Spicer 60
• Includes o-rings

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM88510 race
• All steel construction

Set-up bearing (one bearing). HM803149. No return.

Product Features:

• Set up bearing
• Fits HM803149 pinion bearing
• Easily slips on and off pinion journal to allow for pinion depth adjustment

Pinion seal for Chrysler 8.75″ 42 housing.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Chrysler 8.75″ with ’42’ case housing

Product Features:

• Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80

Product Features:

• DANA-60 R/P 5.13 STD MG (USES PRE-LOAD SHIMS)

8.75″ Chrysler & 55P Chevy Power Lok clutches, Model 20 also, POSI.

Product Features:

• Clutch kit
• Fits Chrysler 8.75″, 1955-1964 GM passenger car and AMC Model 20 Powr Lok positraction

Product Features:

• Inner oil slinger for Dana Spicer 60

Product Features:

• CRUSH SLEEVE CHRYS 8 3/4

Chrysler 8.75″ (coarse spline) pinion nut washer.

Product Features:

• Pinion nut washer
• Fits Chrysler 8.75″ with 10 spline pinion

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Chrysler 8.75″ ’89’ case
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Product Features:

• Rubber fill plug
• Fits Chrysler 7.25″, 8.25″ and 9.25″

Product Features:

• Dropout housing
• Fits Chrylser 8.75″
• ’89’ case design
• Nodular iron for added strength

Product Features:

• Oil baffle for Dana Spicer 60 and Dana Spicer 70U

Yukon axle kit for Chrysler 8.75″. This kit contains two green bearings, ten axle studs and two cut to length axles that fit A, B & E body cars, 5 x 4.5″ pattern.

Product Features:

• 30 spline
• 5 x 4.5″ bolt pattern
• Cut to length design fits 28″-32″ applications
• Axle kit
• Includes two axles, two green bearings and 10 axle studs

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Dana 60 differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits Dana Spicer 60
• Includes carrier bearings and races and carrier shim kit

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

• Fits Chrysler 8.75″ ’42’ case housing with LM104912 carrier races
• Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, thread locker, marking compound with brush, and gasket.

Differential

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit.

Product Features:

• .047″ thick cellulose/nitrile composite gasket material
• Precision die cut
• Reusable

Demand genuine Spicer. Dana design, engineering, testing and manufacturing processes all work in conjunction with one another to ensure unparalleled performance that non-genuine parts simply cannot deliver.

Product Features:

• Genuine OE quality. Tested and proven.
• Built to meet OE standards set by Dana
• Tested and validated to rigorous OE specifications
• Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace

Product Features:

• Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
• Fits standard open differentials only

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

• Cross pin bolt
• Fits Chrylser 7.25″

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

• Power Lok case bolt for Dana Spicer 60 and 70
• 7/16 x 14 thread
• 3.5″ long
• 9/16″ hex head

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years. This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.

Product Features:

• Fits Dana Spicer 60 with 30 spline axles
• 4.10 and down ratio only
• Forged case and 8620 internals for added strength
• Works with a variety of air delivery systems
• Assembled in the USA