1971 Dodge D100 Pickup Drivetrains

Below you will find various in-demand Dodge Drivetrains, components and accessories for your 1971 D100 Pickup. Advance Auto Parts has popular D100 Pickup parts like Transfer Cases, Drive Shafts and Axles, 4WD Components and more. You’ll also find aftermarket and OEM Drivetrains for other D100 Pickup model years including 1957, 1958, 1959, 1968, 1969, 1970, 1972, 1973, 1974 and more. Select a category of 1971 Dodge D100 Pickup Drivetrains below and start saving instantly.

Please Select your Vehicle to See Exact Fit Parts

Popular 1971 Dodge D100 Pickup Drivetrains Categories

Differential Oil

U-Joints

4WD Hubs

Rear Differential Cover Gaskets

Drive Shaft Center Supports

Differential Open Unit and Components

Differential Covers

Center Support Bearings

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Differential Bearings

Differential Pinion Flanges

Differential Axle Shafts

Drive Shaft Bearings

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

Differential Pinion Pilot Bearings

Locking Hub Service Kits

U-Joint Centering Yokes

Axle Shaft Bearings

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Cover Plugs

Differential Clutch Packs

Differential Ring and Pinions

Differential Cases

Differential End Yokes

Spindle Lock Nuts

Differential Lock Assemblies

Differential Spools

Differential Carrier Bearings

Differential Carrier Bearing Adjusters

Differential Pinion Bearing Kits

Axle Shaft Seal Retainers

Complete Differentials

Differential Ring Gear Bolts

Bearing Race Drivers

Spindle Lock Nut Thrust Washers

Input Shaft Seals

Spindle Retainers

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Automatic Transmission Differential Carrier Gaskets

Mounting Adapter Seals

Differential Pinion Gear Thrust Washers

Differential Pinion Gear Washers

Limited Slip Differential Assemblies

Universal Joint Strap Bolts

Differential Clutch Pack Clips

Differential Bearing Adjuster Nut Lock Bolts

Differential Lock Thrust Blocks

Axle Housing Fill Plugs

Essential Drivetrains for 1971 Dodge D100 Pickups

from

$12.99

8.75″ Chrysler gasket.

Product Features:

Dropout gasket
Fits Chrysler 8.75″

from

$213.99

Product Features:

31 spline
5 x 4.5″ bolt pattern
31 11/16″ long
Fits Chrysler 9.25″ in 1979 and down Dodge truck

from

$17.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$17.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$8.49

This universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles
Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$67.99

Powr Lok button kit
Fits Dana Spicer 30, 44 and Chrysler 8.75″

from

$188.99

Yukon yoke for Chrysler 8.75″ with 29 spline pinion and a 7260 U/joint size. 3.125″ snap ring span, 1.078″ cap diameter. Inside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 8.75″
29 spline
7260 u-joint size
2.125″ snap ring span
1.078″ cap diameter
Inside snap ring design
Strap style

from

$519.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty. This is a fine spline pinion which takes a 29 spline yoke.

Product Features:

Fits Chrysler 8.75″ “89” case housing
8.75″ ring gear diameter
29 spline pinion
12 ring gear bolts
4.56 ratio

from

$829.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Chrysler 8.25″ with 27 spline axles
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$8.99

C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.

Product Features:

c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
.150″ thick

from

$301.99

Yukon standard open spider gear kit for ’96 and older 8.25″ Chrysler with 27 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Chrysler 8.25″ open differntial with 27 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$209.99

HUB 4X4-STD MAN LOCK

from

$389.99

Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Chrysler 9.25″
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
Fits Yukon Dura Grip

from

$13.49

Product Features:

KIT SHIM TOYO TRK 79-92 REAR/89-92 FRONT

from

$142.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits Chrysler 8.75″ ’41’ case
Included are a pinion seal, pinion nut, completete shim kit, marking compound and brush.

from

$263.99

Yukon flange yoke for Chrysler 9.25″. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 9.25″ rear
29 spline
Round companion flange

from

$8.99

Spindle nut retainer, 2.030″ I.D., 8 bent over tabs. This replaces Spicer part number 33733.

Product Features:

Spindle nut retainer for Dana Spicer 60, 70, 70U and 70HD
2.030″ I.D.
8 bent over tabs

from

$215.99

Bearing race driver for Dana 60 front, Dana 70U rear, Chrysler 8.75″ with 42 housing, and ’88 and older GM 14T. No return.

Product Features:

Bearing race driver
Fits HM803110 race
All steel construction

from

$474.99

Product Features:

Dropout housing
Fits Chrylser 8.75″
’89’ case design
Nodular iron for added strength

from

$22.99

Product Features:

Rubber fill plug
Fits Chrysler 7.25″, 8.25″ and 9.25″

from

$7.29

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$9.99

Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality

Product Features:

Fill plug
Fits Chrysler 8.75″

from

$107.99

Product Features:

BEARING KIT 8.75 CHRY 1.875 489 CST OPEN/AUBURN/TRUETRAC/DET.LOCKER

from

$173.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Chrysler 9.25″ rear differential. This kit contains carrier bearings and races.

Product Features:

Fits Chrysler 9.25″ rear
Includes carrier bearings and races

from

$159.99

Fits Chrysler 8.25″
Steel

from

$12.99

9.25″ pinion gear thrust washer.

Product Features:

Pinion gear thrust washer for Chrysler 9.25″ rear

from

$26.99

8.25″ Chrysler pinion gear thrust washer.

Product Features:

Pinion gear thrust washer
Fits Chrysler 8.25″

Upgrade your 1971 Dodge D100 Pickup with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1971 Dodge D100 Pickup, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Dodge or enhancing its overall performance, Drivetrains are key to keeping your D100 Pickup functioning at its best. At Advance Auto Parts, we offer a wide selection of 273 Drivetrains for the 1971 Dodge D100 Pickup, designed to meet your needs without breaking the bank. From Transfer Case replacements to Drive Shafts and Axles upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1971 Dodge D100 Pickup at great prices. Our Drivetrains inventory for this model ranges from just $2.99 to $1,566.99, with an average price of $209.39. Our 273 Drivetrains in stock come from 17 trusted brands, so you’re sure to find the right part for your 1971 Dodge D100 Pickup without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1971 Dodge D100 Pickup, we stock popular OEM and aftermarket Drivetrains from top names like Moog, National, Dorman, and more. Moog Drivetrains start at just $36.99 and boast an impressive 4.5 stars average rating from customers. National and Dorman also bring quality to the table, with Drivetrains available starting at $3.49, and at an average 4.3 stars rating. With 1,602 customer reviews and counting, our 1971 Dodge D100 Pickup Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1971 Dodge D100 Pickup is always ready to roll. We’re committed to providing you with everything you need to keep your D100 Pickup in top shape, all in one place. Start shopping confidently below for your 1971 Dodge D100 Pickup!

Best-Selling Transfer Cases for 1971 Dodge D100 Pickups

Enhance the driving experience in your Dodge with 7 quality Transfer Case components, starting at $5.99.

show more show less

from

$15.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$30.49

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$15.49

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$19.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$5.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; single-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$7.29

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$10.49

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

Most Popular 1971 Dodge D100 Pickup Drive Shafts and Axles

Customize your Dodge with 19 Drive Shafts and Axles products like Axle Shaft Seals, Axle Shaft Bearings, and Center Support Bearings, all priced under $289.99.

show more show less

from

$40.99

Anchor 6038 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 4 Lbs
BEARING ID / BORE: 1.5750 In. / 40 mm
CENTERLINE: 2.48 In. / 63 mm
Mount Width: 6.62 In. / 168 mm
Style: Round Frame
Not Pictured: Two Dust Shields

from

$17.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$44.99

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

BUILT TO LAST – Advanced heat treatment process for strength
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$21.99

Anchor 6056 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 3 Lbs
BEARING ID / BORE: 1.3780 In. / 35 mm
CENTERLINE: 2.28 In. / 58 mm
Mount Width: 6.62 In. / 168 mm
Style: Round Frame
Complete Mount

from

$19.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$8.99

C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.

Product Features:

c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
.150″ thick

from

$8.99

8.75″ Chrysler inner axle seal, use w/set7.Yukon Mighty seal.

Product Features:

Rear inner axle seal
Fits Chrysler 8.75″ rear
Tapered rolling bearing design only

from

$17.99

9.25″ Chrysler C/clip, 0.205″ wide for 4137429 axle.

Product Features:

c-clip for Chrysler 9.25″ rear
0.205″ thick

from

$15.99

8.75″ Chrysler outer axle seal, use w/set7.Yukon Mighty seal.

Product Features:

Rear outer axle seal
Fits Chrysler 8.75″ rear
Tapered rolling bearing design only

from

$35.99

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$9.99

Fill plug
Fits Chrysler 8.75″

from

$289.99

Yukon yoke for Chrysler 9.25″ with a 7260 U/joint size. 2.125″ snap ring span, 1.078″ cap diameter. Inside snap ring.All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 9.25″ rear
29 spline
7260 u-joint size
Inside snap ring design
2.125″ snap ring span
1.078″ cap diameter
Strap style

from

$279.99

Yukon yoke for Chrysler 9.25″ with a 7290 U/joint size. 2.625″ snap ring span. 1.125″ cap diameter. Inside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 9.25″ rear
29 spline
7290 u-joint size
2.625″ snap ring span
1.125″ cap diameter
Inside snap ring design
Strap style

from

$266.99

Yukon yoke for Chrysler 8.75″ with 10 spline pinion and a 7290 U/joint size (1350 with U/joint adapter.) All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 8.75″
10 spline
7290 u-joint size
Inside snap ring design
2.625″ snap ring span
1.125″ cap diameter
Strap style

from

$213.99

Yukon yoke for Chrysler 8.75″ with 10 spline pinion and a 7260 U/joint size. 2.125″ snap ring span, 1.078″ cap diameter. Inside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 8.75″
10 spline
7260 u-joint size
Inside snap ring design
2.125″ snap ring span
1.078″ cap diameter
Strap style

from

$188.99

Fits Chrysler 8.75″
29 spline
7260 u-joint size
2.125″ snap ring span
1.078″ cap diameter
Inside snap ring design
Strap style

from

$64.99

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$10.79

We develop and produce high-quality roller bearings, spherical bearings, and plain bearings worldwide for a wide range of applications.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$6.29

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

Top Picks for 1971 Dodge D100 Pickup 4WD Components

Upgrade Dodge D100 Pickups with top-quality 4WD Components parts, including 1 OEM and aftermarket selections for your 1971 model.

show more show less

from

$297.99

HUB 4X4-PREM MAN LCK

In-Demand Universal Joints for 1971 Dodge D100 Pickups

Select from 28 premium Universal Joints parts for your 1971 Dodge D100 Pickup, with prices ranging from $3.99 to $217.99.

show more show less

from

$31.99

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$44.99

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$38.99

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$36.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$26.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 315G, 317, 319 & 457
Contains two 1-1/2″ bolt center clamps and four 1/4-28 x 5/8″ cap screws

from

$29.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$36.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$34.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$8.49

Direct replacement – this universal joint strap kit is designed to match the original components required to repair and resecure universal joints on specified vehicles
Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$18.99

1310 & 1330 U/joint strap, Dana 30, Dana 44, Model 35, & 9.25″ w/bolts.

Product Features:

u-joint strap kit
Fits Dana Spicer 30 and 44, AMC Model 35 and Chrysler 9.25″
1310 and 1330 u-joint size
Includes two straps and four bolts

from

$10.99

For U-Joints 316 & 458
Contains two 1.54″ bolt center clamps and four 1/4-28 x 5/8″ cap screws

from

$44.99

Yukon 1310 U/Joint with zerk fitting on cross. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$45.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

from

$59.99

Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.

from

$78.99

Yukon 1350 to 1410 conversion u/joint.

from

$109.99

Yukon 1310 to Mechanics 3R adapter U/Joint.

from

$63.99

Yukon 1350 Lifetime Series U/Joint. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring.

from

$52.99

7290 U/joint strap kit (4 bolts and 2 straps) for Chrysler 7.25″, 8.25″, 8.75″, and 9.25″.

Product Features:

u-joint strap kit
Fits Chrysler 7.25″, 8.25″ 8.75″ and 9.25″ rear
7290 u-joint size
Includes two straps and four bolts

from

$51.99

Yukon 1350 U/Joint with zerk fitting. 3.625″ snap ring span, 1.118″ cap diameter. Outside snap ring.

from

$57.99

1310 Yukon Lifetime U/joint. 1.718″ snap ring span, 1.062″ cap diameter. Inside snap ring.

from

$217.99

Yukon extra HD yoke for Chrysler 8.75″ with 10 spline pinion and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 8.75″
10 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
Strap style

from

$209.99

Yukon extra HD yoke for Chrysler 8.75″ with 29 spline pinion and a 1350 U/joint size. 3.625″ snap ring span, 1.118″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 8.75″
29 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
U-bolt style

from

$111.99

Yukon 1350 to Mechanics 3R adaptor U/joint.

Most Sold 1971 Dodge D100 Pickup Differentials

Explore our best-selling Dodge parts for the 1971 D100 Pickup among 212 OEM and aftermarket options starting from $2.99.

show more show less

from

$18.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$7.49

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$384.99

This differential ring and pinion directly replaces the original equipment on specific vehicle years, makes and models.

Product Features:

Direct replacement – this ring and pinion set matches the fit and function of the original components on certain vehicle applications
Effective fix – eliminates grinding and whining from failed original bearings
Thoroughly tested – vehicle try-on testing and rigorous quality control measures ensure longevity
Trustworthy quality – backed by team of designers and engineers in the United States

from

$46.99

Cross pin shaft for standard open Chrysler 9.25″, .860″ diameter. Will not fit posi!

Product Features:

Cross pin shaft for Chrysler 9.25″
Fits standard open differentials only
0.860″ diameter

from

$11.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$168.99

Product Features:

C9.25 OPEN INTERNAL KIT, 1984-UP

from

$419.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits 2010 and down Chrysler 9.25″ rear
9.25″ ring gear diameter
29 spline pinion
12 ring gear bolts
4.11 ratio

from

$9.29

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$178.99

This differential bearing kit includes all necessary installation components for a differential ring and pinion on certain vehicle years, makes and models.

Product Features:

Convenient kit – this ring and pinion bearing installation kit includes all necessary components for a complete repair on certain vehicle applications
Related repair – smart to have on hand when installing a differential ring and pinion
Durable construction – built for reliable longevity, free of defects in materials and workmanship
Trustworthy quality – backed by team of designers and engineers in the United States

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$9.99

Ring gear bolt for Chrysler 9.25″ rear, 7/16″ x 18.

Product Features:

Ring gear bolt for Chrysler 9.25″ rear

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$10.99

Crush Sleeve for Model 35, Chrysler 7.25″, 8.25″ Ford 8″ & GM 7.75″. Approx 0.495″ long.

Product Features:

Crush sleeve for AMC Model 35, Chrysler 7.25″ and 8.25″, Ford 8″ and GM 7.75″
0.495″ tall

from

$34.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$309.99

from

$7.99

Product Features:

CHRY 8 3/4″ RING GEAR BOLTS C 8.25″

from

$8.99

Ring gear bolt for Chrysler 7.25″, 8″ IFS, 8.25″, 8.75″ & GM 7.2″ IFS front. 3/8″ x 24.

Product Features:

Ring gear bolt for Chrysler 7.25″, 8.0″ IFS and 8.75″
3/8″ x 24 thread
.866″ long

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$27.99

8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.

Product Features:

Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″

from

$10.99

Pinion nut for Chrysler 7.25″, 8.0″ IFS, 8.25″, 8.75″ fine spline, 9.25″ front & rear, 7/16″ x 14.

Product Features:

Pinion nut for Chrysler 8.0″ IFS, 8.25″, 8.75″ with 29 spline pinion and 9.25″ rear
7/8″ x 14 thread

from

$319.99

Product Features:

CHRY 12BLT 9.25 R&P-3.55 RATIO

from

$21.99

8.75″ Chrysler & 9″ Ford preload shim kit.

Product Features:

Preload shim kit for Ford 9″ and Chrysler 8.75″ with ’41’ and ’42’ case housing

Top-Rated Drivetrains Brands For Your 1971 Dodge D100 Pickup

Shop for the best-rated brands offering Drivetrains and other products for your 1971 Dodge D100 Pickups. Below you’ll find some of our best rated Drivetrains from Moog, National, and Dorman, and more. Drivetrains from these brands that fit a 1971 D100 Pickup start at just $3.49 and are rated as high as 4.5 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Moog 1971 Dodge D100 Pickup Drivetrains

When it comes to maintaining or upgrading your 1971 Dodge D100 Pickup, using quality Drivetrains is essential to ensure durability and a perfect fit. Moog ticks all of those boxes. We offer a wide selection of Moog Drivetrains, specifically designed for the 1971 Dodge D100 Pickup. With over 3 Moog brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $36.99, with an average price of just $40.32. Plus, with over 6 customer reviews and an average rating of 4.5 stars, you can trust that our Moog Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $38.99

(3)

Greaseable Super Strength Universal Joint

“Quality part”

from $36.99

(1)

Greaseable Premium Universal Joint

“the u-joint itself fit fine however the grease fitting is too large for the hole provided in the u-joint. I had to enlarge the hole to fit the fitting”

from $44.99

(2)

Greaseable Super Strength Universal Joint

“Always there to get what you need!”

Popular National 1971 Dodge D100 Pickup Drivetrains

National auto parts is one of the highest quality Drivetrain brands in the market. Any 1971 Dodge D100 Pickup owner should feel confident when installing genuine National parts in their vehicle. To ensure the best fit and performance for your 1971 D100 Pickup, Advance Auto Parts carries a full inventory of 3 National Drivetrains. Plus you will be keeping your Dodge in peak condition while saving money because prices on these National Drivetrains range from $15.99 to $30.49, plus, with more than 11 customer reviews and an impressive 4.3 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from $18.99

(1)

Multi-Purpose Seal

“Perfect fit and in stock for a 50 year old vehicle. Thanks Advance Auto Parts”

from $30.49

(1)

Shaft Repair Sleeve

“Perfect Fit. Product was exactly as described”

from $15.99

(9)

Bearing

“as advertised”

FAQs for 1971 Dodge D100 Pickup Drivetrains

Which Drivetrains are best-sellers for 1971 Dodge D100 Pickups?

Out of 273 Drivetrains that fit 1971 Dodge D100 Pickups, the following parts are the top sellers:

Center Support Bearing Motor Mount: Center, 1 Piece (5300924) – $21.99
3 Qt – 80W90 Conventional Gear Oil With Posi Additive (11645418) – $57.99
3 Qt – Penzoil 80W90 Conventional Gear Oil (11644279) – $44.99

What’s the price range for 1971 Dodge D100 Pickup Drivetrains?

Drivetrain prices for the 1971 Dodge D100 Pickup start at $2.99 and go up to $1,566.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1971 Dodge D100 Pickup?

The average price for Drivetrains for the 1971 Dodge D100 Pickup is $209.39. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Dodge D100 Pickup model years?

Yes, we currently carry Drivetrains for 8 model years of Dodge D100 Pickups between 1957 and 1974. Drivetrains are bought most frequently for the following model years: 1974, 1973, 1972, 1970, 1969, 1968, 1959, 1958, and 1957.

What are the cheapest Drivetrains for my 1971 Dodge D100 Pickup?

The cheapest 1971 Dodge D100 Pickup Drivetrains we carry in stock are:

Differential Crush Sleeve (10592883) – $2.99
Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (21260547) – $3.49
Universal Joint (5270200) – $3.99
Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (sold by each) (22149122) – $4.79
Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm (21260519) – $5.49

What are the top-rated Drivetrains that fit the 1971 Dodge D100 Pickup?

Out of 1,602 reviews by customers, our 1971 Dodge D100 Pickup Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1971 Dodge D100 Pickup and their top-rated products:

Spindles
- Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm (21260519) – $5.49
- Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (21260547) – $3.49
Universal Joints
- Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm (21260519) – $5.49
- Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (21260547) – $3.49

What types of Drivetrains do you sell for my 1971 Dodge D100 Pickup?

As of 3/1/26, these are some of the most in-demand types of Drivetrains for a 1971 Dodge D100 Pickup:

Can I get help with 1971 Dodge D100 Pickup Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Dodge Drivetrains and more.

What is your return policy for Dodge D100 Pickup Drivetrains?

Advance Auto Parts keeps returns simple. For new Dodge D100 Pickup Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1971 Dodge D100 Pickup Drivetrains

Yukon Gear – 8.75" Chrysler Gasket (Part No.23001)

USA Standard Gear – Axle For ’79 & Older Chrysler Truck, 9.25" (Part No.35104)

National – Multi-Purpose Bearing (Part No.A-5)

National – Multi-Purpose Bearing (Part No.A-18)

Dorman – Help – U-Joint Repair Kit (Part No.81006)

Yukon Gear – Powr Lok Button Kit For Dana 30, Dana 44 & Chrysler 8.75" (Part No.33536)

Yukon Gear – Yoke For Chrysler 8.75" With 29 Spline Pinion And A 7260 U/Joint Size (Part No.41007)

Yukon Gear – High Performance Ring & Pinion Gear Set For Chrysler 8.75" With 89 Housing In A 4.56 Ratio (Part No.24242)

USA Standard Gear – Spartan Locker For Chrysler 8.25" With 27 Spline Axles, Includes Heavy-Duty Cross Pin Shaft (Part No.17037)

Yukon Gear – Cross Pin Bolt (Part No.33067)

Yukon Gear – C/Clip (Part No.33083)

Yukon Gear – Standard Open Spider Gear Kit For ’96 And Older 8.25" Chrysler With 27 Spline Axles (Part No.16002)

Warn – HUB 4X4-STD MAN LOCK (Part No.9790)

Yukon Gear – Positraction Spiders For Chrysler9.25" Dura Grip Posi, 31 Spline, No Clutches Included (Part No.16180)

Motive Gear – Differential Pinion Shim Kit (Part No.1109)

Yukon Gear – Minor Install Kit For Chrysler 41 8.75" Differential (Part No.12005)

Yukon Gear – Flange Yoke For Chrysler 9.25" (Part No.41012)

Yukon Gear – Spindle Nut Retainer, 2.030" I.D., 8 Bent Over TABS (Part No.33480)

Yukon Gear – Bearing Race Driver (Part No.56011)

USA Standard Gear – 8.75" Chrysler 89 Drop Out Case, Up To 500 Hp, Nodular Iron (Part No.59001)

Yukon Gear – Rubber Fill Plug For Chrysler (Part No.33463)

National – Manual Transmission Input Shaft Seal (Part No.9376)

Yukon Gear – Fill Plug For Chrysler 8.75", 3/4" Thread (Part No.33462)

Motive Gear – Differential Bearing Kit – Timken (Part No.R8.75RLAT)

Yukon Gear – Carrier Installation Kit For Chrysler 9.25" Rear Differential (Part No.57001)

Yukon Gear – Steel Cover For Chrysler 8.25" (Part No.32312)

Yukon Gear – 9.25" Pinion Gear Thrust Washer (Part No.33274)

Yukon Gear – 8.25" Chrysler Pinion Gear Thrust Washer (Part No.33273)

National – Bearing (Part No.M88048)

National – Shaft Repair Sleeve (Part No.99138)

National – Bearing Race (Part No.HM88610)

Driveworks – Taper Bearing Cone (Part No.S-HM-88649)

National – Manual Transmission Input Shaft Seal (Part No.482163N)

National – Manual Transmission Input Shaft Seal (Part No.9376)

Schaeffler – Bearing Cone (Part No.KLM11949)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)

National – Multi-Purpose Bearing (Part No.A-5)

National – Drive Shaft Center Support Bearing (Part No.HB-88107-A)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)

National – Tapered Roller Bearing Cone (Part No.HM88649)

Yukon Gear – C/Clip (Part No.33083)

Yukon Gear – 8.75" Chrysler Inner Axle Seal, Use With Set7 (Part No.30198)

Yukon Gear – 9.25" Chrysler C/Clip (Part No.33075)

Yukon Gear – 8.75" Chrysler Outer Axle Seal, Use With Set7 (Part No.30199)

National – Multi-Purpose Bearing (Part No.88107-BVV)

Yukon Gear – Fill Plug For Chrysler 8.75", 3/4" Thread (Part No.33462)

Yukon Gear – Yoke For Chrysler 9.25" With A 7260 U/Joint Size. (Part No.41001)

Yukon Gear – Yoke For Chrysler 9.25" With A 7290 U/Joint Size (Part No.41002)

Yukon Gear – Yoke For Chrysler 8.75" With 10 Spline Pinion And A 7290 U/Joint Size (Part No.41130)

Yukon Gear – Yoke For Chrysler 8.75" With 10 Spline Pinion And A 7260 U/Joint Size (Part No.41006)

Yukon Gear – Yoke For Chrysler 8.75" With 29 Spline Pinion And A 7260 U/Joint Size (Part No.41007)

Schaeffler – Bearing – CRB (Cylindrical Roller Bearing) (Part No.102549)

Schaeffler – Bearing – CRB (Cylindrical Roller Bearing) (Part No.FC67148.5)

Schaeffler – Shaft Seal (Part No.SS2698)

Warn – HUB 4X4-PREM MAN LCK (Part No.20990)

Driveworks – Universal Joint (Part No.DW-316)

Driveworks – Universal Joint (Part No.DW-315G)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.246)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.248)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.317)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.318-10)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.245)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.316)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.315G)

Dorman – Help – U-Joint Repair Kit (Part No.81006)

Yukon Gear – 1310 & 1330 U/Joint Strap, Dana 30, Dana 44, Model 35, & 9.25" With Bolts (Part No.41195)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.316-10)

Yukon Gear – 1310 U/Joint With Zerk Fitting On Cross (Part No.42008)

Spicer – Universal Joint (Part No.5-789X)

Yukon Gear – 1310 To 1330 Adapter U/Joint (Part No.42005)

Yukon Gear – 1350 To 1410 Conversion U/Joint (Part No.42006)

Yukon Gear – 1310 To Mechanics 3R Adapter U/Joint (Part No.42013)

Yukon Gear – 1350 Lifetime Series U/Joint (Part No.42021)

Yukon Gear – 7290 U/Joint Strap Kit (4 Bolts And 2 Straps) For Chrysler 7.25", 8.25", 8.75", And 9.25" (Part No.41013)

Yukon Gear – 1350 U/Joint With Zerk Fitting (Part No.42010)

Yukon Gear – 1310 Lifetime U/Joint (Part No.42003)

Yukon Gear – Extra HD Yoke For Chrysler 8.75" With 10 Spline Pinion And A 1350 U/Joint Size (Part No.41014)

Yukon Gear – Extra HD Yoke For Chrysler 8.75" With 29 Spline Pinion And A 1350 U/Joint Size (Part No.41015)

Yukon Gear – 1350 To Mechanics 3R Adaptor U/Joint (Part No.42001)