1970 Mercury Capri Drivetrains
More 1970 Mercury Capri Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1970 Mercury Capri, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1970 Mercury Capri Drivetrains
ARP Auto Racing – For Use With Ford 8.8 And 9" Using 3/4"Socket, 0.75"L Under Head, 7/16"-20 (Part No.250-3003)
from
$34.99
The tremendous shock loads generated at launch by most any drag racing vehicle equipped with today sticky tire compounds or the acceleration and deceleration of oval track cars put considerable strain on the ring gear. For this reason, the fastener experts at ARP have developed the Pro Series ring gear bolts. they are forged from premium grade 8740 chrome moly steel and are heat treated to a nominal rating of 200,000 PSI tensile strength. Specially hardened, precision ground washers are included where required. Available to fit most any ring gear setup ranging from popular 9 Inch Ford GM 10 and 12 bolt rear ends to the beefy strange differentials found in top fuel and funny car applications.
Product Features:
See More
Product Features:
- Forged From Premium Grade 8740 Chrome Moly Steel
- Heat Treated
- Nominally Rated At 200,000 Psi Tensile Strength
- Specially Hardened, Precision Ground Washers
- 0.75″ Underhead Length
- 200,000 PSI
- Sold As A Set
Yukon Gear – The Carrier Bearing Puller (Part No.56072)
from
$883.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.
Product Features:
See More
Product Features:
- Carrier bearing puller
- Works with an impact gun to safely and easliy remove carrrier bearings
Driveworks – Tapered Cone/Cup Wheel Bearing Set (Part No.S-A-35)
from
$13.99
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Yukon Gear – 1310 Lifetime U/Joint (Part No.42003)
from
$57.99
1310 Yukon Lifetime U/joint. 1.718″ snap ring span, 1.062″ cap diameter. Inside snap ring.
See More
National – Shaft Repair Sleeve (Part No.99181)
from
$37.49
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
- Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
Powertrax – Lock Right Locker (Part No.1830-LR)
from
$444.99
The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles. Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction. Powertrax® = Extreme Traction Systems!
See More
Yukon Gear – 8" Ford Pinion Seal (Part No.30180)
Yukon Gear – 14 Plate Duragrip Composite Clutches For GM 8.2", GM 8.5", 12T, 12P, Ford 8.8" & Cast Iron ‘Vette (Part No.16064)
from
$373.99
Product Features:
See More
- Clutch kit
- Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
- 14 piece kit
- Composite clutches
Yukon Gear – 8" Ford O-Ring (Part No.30027)
Yukon Gear – Un-Notched Cross Pin Shaft For 7.5" Ford – Oem, Not Auburn Gear (Part No.33330)
from
$36.99
Un-notched cross pin shaft for 7.5″ Ford. OEM, not Auburn gear.
Product Features:
See More
Product Features:
- Cross pin shaft for Ford 7.5″
- 3.45 and down ratios only
Driveworks – Oil Seal (Part No.S-8660S)
from
$5.49
Value-priced seal meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Yukon Gear – Pinion Depth Shims For GM 8.25" IFS, 8.5", 12 Bolt Car, Ford 8.8" & Chrysler 8.25" (Part No.55009)
from
$27.99
8.25″ IFS, 8.5″, 12P, 7.5″ F, 8.8″ F, 8.25″ Chrysler pinion shim kit.
Product Features:
See More
Product Features:
- Pinion depth shims for GM 8.25″ IFS, 8.5″, 8.6″, 12 bolt passenger car, Ford 7.5″ and 8.8″, Chrysler 8.25″
Yukon Gear – Bearing Install Kit For Ford 8" Differential With Aftermarket Positraction Or Locker (Part No.11112)
from
$236.99
Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.
Product Features:
See More
Product Features:
- Fits Ford 8″ with aftermarket positraction
- Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.
Yukon Gear – Redline Synthetic "Shock Proof" Oil – 4 Quarts (Part No.15004)
from
$137.99
Redline Synthetic “Shock Proof” Oil. 4 Quarts.
Product Features:
See More
Product Features:
- Includes four quarts of Redline Shockproof oil
Yukon Gear – Pinion Gear And Thrust Washer (0.750" Shaft) For 8.8" Ford (Part No.33297)
from
$8.99
Pinion gear thrust washer (0.750″ shaft) for 8.8″ Ford.
Product Features:
See More
Product Features:
- Pinion gear thrust washer
- Fits Ford 8.8″
- 0.750″ I.D.
USA Standard Gear – Standard Spider Gear Set For Ford 8.8", 28 Spline (Part No.39015)
from
$209.99
Product Features:
See More
- Spider gear kit
- Fits Ford 8.8″ 28 spline open differential
- Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
Yukon Gear – 7.5" Ford Cover Gasket (Part No.23009)
USA Standard Gear – Master Overhaul Kit for the Ford 7.5 Differential (Part No.37027)
from
$199.99
USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.
Product Features:
See More
Product Features:
- Fits Ford 7.5″
- Uses Koyo bearings and races
- Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.
Yukon Gear – Crush Sleeve (Part No.33085)
from
$9.99
Crush Sleeve for Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9 3/8″, 9″ & 9.75″. .480″ long.
Product Features:
See More
Product Features:
- Crush sleeve for AMC Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9″ and 9.75″
- 0.480″ tall
Yukon Gear – Dana 44, Ford 8" / 9", And Model 20 Side Gear Thrust Washer Replacement (Part No.33283)
from
$5.99
Product Features:
See More
- Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
- 0.030″ thick
Yukon Gear – Dura Grip For Ford 7.5" (Part No.26034)
from
$789.99
The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 in
Product Features:
See More
Product Features:
- Fits Ford 7.5″
- 28 spline
- 4-spring, clutch style positraction
- Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
- Fully rebuildable
- Assembled in the USA
National – Bearings (Part No.M88010)
from
$10.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Super Carrier Shim Kit For Ford 8.8", GM 12 Bolt Car & Truck, 8.6 & Vette (Part No.55002)
from
$59.99
Product Features:
See More
- Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
- Interlocking design makes installation much easier
Yukon Gear – Dura Grip Case For Ford 8.8", 31 Spline (Part No.20073)
from
$386.99
Product Features:
See More
- Dura Grip positraction carrier case
- Does not include spider gears
- Fits Ford 8.8″ with 31 spline axles
Motive Gear – Differential Ring and Pinion (Part No.F8.8-488)
Yukon Gear – Pinion Install Kit For Ford 8.8" Differential (Part No.13041)
from
$167.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.
Product Features:
See More
Product Features:
- Fits 2009 and down Ford 8.8″
- Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.
Yukon Gear – Trac Loc Spring Plate For Ford 9" & 8" (Part No.33517)
Yukon Gear – Pinion Support Bolt For 8" And 9" Ford (Part No.33242)
from
$6.99
Pinion support bolt for 8″ and 9″ Ford.
Product Features:
See More
Product Features:
- Pinion support bolt for Ford 8″ and 9″
- 3/8″ x 24 thread
- 1.0″ long
Popular 1970 Mercury Capri Drivetrains Categories
1970 Mercury Capri Drivetrains
You count on your 1970 Mercury Capri to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 72 Drivetrains ranging in price from $3.99 to $931.99, you’re sure to find everything you need for your 1970 Mercury Capri.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 6 different brands like Yukon Gear, Dorman, and National. 1970 Mercury Capri Drivetrains start as low as $3.99!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 1 extensive product reviews on 1970 Mercury Capri Drivetrains.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1970 Mercury Capri below to get started!
Top-Rated Drivetrains Brands For Your 1970 Mercury Capri
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1970 Mercury Capri running right for years to come. In our inventory you’ll find brands like Yukon Gear, Dorman, National, and even more.
Popular National Drivetrains
You’ll find popular National brand products across Differentials. All are waiting to get your 1970 Mercury Capri back on the road. Some of the top-rated National products in these categories are:
FAQs for 1970 Mercury Capri Drivetrains
What are the most purchased Drivetrains for the 1970 Mercury Capri?
Out of 72 Drivetrains for the 1970 Mercury Capri, the most popular in our inventory are:
from
$5.99
This product is not rated
Copper Washer For Ford 9" & 8" Dropout Housing
Complete Differentials
