1970 Mercury Capri Differentials

7.5″ Ford cover gasket.

Product Features:

• Cover gasket
• Fits Ford 7.5″

Product Features:

• Spider gear kit
• Fits Ford 8.8″ 31 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon-Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 8″ with 31 spline axles
• Trac Loc positraction
• Clutch style positraction
• Aggressive design
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Pinion gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

• Pinion gear thrust washer
• Fits Ford 8.8″
• 0.750″ I.D.

Valvoline Import Multi-Vehicle Automatic Transmission Fluid is specifically formulated for use in most Toyota, Nissan, Honda and other imported vehicles. It is formulated with all synthetic base stocks and a proprietary additive system to ensure optimal transmission performance in a wide variety of vehicles. Valvoline Import Multi-Vehicle ATF can also be used in many domestic vehicles. It meets requirements of General Motors and Ford vehicles. Recommended for use in the following applications: Ford MERCON, GM DEXRON-II and DEXRON-III, BMW LT 71141 and ETL-7045E, Nissan/Infiniti Nissan ATF, Matic-D, Matic-K and Matic-J, Mitsubishi Diamond SP-II and SP-III, Subaru ATF-HP, Hyundai/ KIA SP-II and SP-III, Toyota/Lexus Type T, T-III and T-IV, Honda/Acura ATF-Z1 (except in CVTs), Mercedes Benz NAG1, Volvo passenger car (except AW-1), and Volkswagen/Audi TL52162. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M86610 race
• All steel construction

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

Product Features:

• Trac Loc spring
• Fits 28 spline Ford 8.8

Trac Loc ring gear bolt washer for 8″ and 9″ Ford.

Product Features:

• Ring gear bolt for Ford 8″ and 9″
• For Trac Loc positraction applications only

Worn or damaged differential end yoke causing driveline Vibrations! This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

• Direct replacement – this differential end yoke matches the fit and construction of the original yoke
• Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
• Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
• Validated fit – this differential end yoke has been tested to confirm accurate fit

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 in

Product Features:

• Fits Ford 7.5″
• 28 spline
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits 2009 and down Ford 8.8″
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

8″ Ford pinion seal.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Ford 8″

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

• Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

Product Features:

• FRD 10BL 8.8 R/P 3.27 MG

Crush Sleeve for Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9 3/8″, 9″ & 9.75″. .480″ long.

Product Features:

• Crush sleeve for AMC Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9″ and 9.75″
• 0.480″ tall

Pinion support bolt for 8″ and 9″ Ford.

Product Features:

• Pinion support bolt for Ford 8″ and 9″
• 3/8″ x 24 thread
• 1.0″ long

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

Spindle nut washer for Dana 28, ’92 & down. This replaces Spicer part number 40075.

Product Features:

• Spider gear kit
• Fit Ford 7.5″ open differential
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 8″
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

8″ Ford O-ring.

Product Features:

• Pinion support o-ring
• Fits Ford 8″

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

8″ Ford pilot bearing retainer.

Product Features:

• Pilot bearing retainer for Ford 8″

Side gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

• Side gear thrust washer for Ford 8.8″
• 0.750″ diameter cross pin shaft applications only

9.25 Chrysler FRONT PINION KIT , 03 & UP DODGE TRUCK .

Product Features:

• Pilot bearing
• Fits Ford 8″

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits Ford 8″ with aftermarket positraction
• Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.

7.5″, 8″, 8.8″, 9″, 10.25″ Ford REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

• Redi-Sleeve yoke saver
• Fits Ford 7.5″, 8.8″, 9″ and 10.25″

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on