from

$258.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$29.99

Product Features:

Timing Chain Only

from

$499.99

Torque Converter – Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: Tork Master 3000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) The Tork Master is B&M’s lowest cost performance torque converter. The Tork Master is an excellent all-around performance street converter. The best ‘value priced’ street converters available, Tork Master converters come with a new precision pump drive tube and all are pressure tested and fully balanced. The Tork Master torque converter is not recommended for big block or supercharged applications. New allow steel pump drive tube. Needle thrust bearing when factory equipped. New thrust washer between turbine and cover when required.

Product Features:

New Precision Pump Drive Tube
Pressure Tested
Fully Balanced
Needle Thrust Bearing
New Thrust Washer
Washer Between Turbine and Cover

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$14.99

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

Precision Machined
Case Hardened
Give Accurate Alignment
2 Per Set

from

$73.99

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

Cylinder Head Bolts
Longer-Than-Stock
High Quality Grade 8 Alloy
Increase Torque Settings
Higher Clamp Loads On Gasket

from

$17.49

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

Zinc plated to resist corrosion and provide a clean professional appearance
Made from Grade 5 steel for strength and durability
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Allen (socket) Head
Zinc Plated For Protection

from

$39.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$215.99

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

Twisted Snout Water Pump Design For Updated Style
Street Performance
Heavy Duty Shaft w/5/8 in. Pilot
Six-Blade Stamped Steel
Anti-Cavitation Impeller
100 Percent Leak Tested

from

$16.49

Precision timing tape can be used on a factory balancer to create HP through accurate timing, and makes setting valve lash simple.

Product Features:

8″ diameter
1970-73, 396-427-454 cu. in.
1967-69, 302 cu. in.
1965-68, 327 cu. in. hi-performance
1970-76, 400 cu. in.
1970-73, 350 cu. in.

from

$23.99

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

Repairs That Leaky Rear Main Sail
Silicone Rubber to Withstand Extreme Engine Oil Temperatures
Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
Injection Molded for Precise Fit

from

$58.99

Chrome water neck with a swivel top allows you to place your coolant hose where you want it to be, not just where the neck allows. Precision die cast for better fitment, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

Chrome Plated Aluminum
O-ring To Prevent Leaks
Swivels For Hard To Fit Applications
Comes With Allen Head Bolts

from

$25.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$334.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$29.49

Molded rubber gaskets are reusable, great for engines that require valve lash maintenance. These gaskets feature Nitrile material for long life, solid steel carrier for strength and rigidity. Incorporates compression limiters to prevent fastener over-tightening.

Product Features:

Features Nitrile Rubber Material For Long Life
Molded Rubber Gaskets Are Reusable
Ideal For Engine Requiring Valve Lash Maintenance

from

$94.99

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Prevents Stud Flexing
Black Plated Finish

from

$187.99

Product Features:

Case-Hardened Tubing
Surface Hardening
Welded Ends
0.3125 in. Diameter
Use with or without Hardened Steel Guideplates

from

$80.99

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$31.99

Edelbrock part #6998 Front Timing Cover Gasket set for Big-Block Chevy. Includes front cover gasket and front seal.

Product Features:

Includes replacement timing cover and water pump gaskets and the crank oil seal for big block Chevrolet engines
Features a tough, scuff-resistant silicone rubber coating
Helps in sealing without the engine warming up
Reduces fluid migration through the gasket
Resists fatigue

from

$411.99

Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.

Product Features:

Designed for 2500 to 6500 Performance
Designed for Hi-Perf Street; Drag or Marine Use
Matched to Edelbrock Torker II Intakes
Includes Hydraulic Lifters and Assembly Lube
Dyno Matched/Street Proven Performance
Take The Guesswork Out Of Camshaft Selection

from

$99.99

Product Features:

Use W/ Valve Springs Part #5703, 5794
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$95.99

Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:

Valve Spring Retainers for Use OE Cast Iron Heads
Superior Quality Heat-Treated Steel
Machined for Strength with Black Oxide Finish
Finish Ensures Rust and Corrosion Protection

from

$32.99

Product Features:

Clean Positive Seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads

from

$48.49

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Silicone beading on both sides of each gasket
Complete with manifold end seals and distributor gasket
For OE replacement, high performance street, drag race and oval track use
Creates Tight Leak proof Seal

from

$674.99

Product Features:

Polished PN[5420] Hand-Buffed for Brilliant Shine
Designed for 1500 to 6000 RPM Performance
Manifold has a Balanced 180+ Firing Order
Smooth and Consistent Part-Throttle Power
Makes +25 HP over Edelbrock Torker II
Makes +30 ft/lbs of Torque over Performer
Metering Rods To Calibrate Edelbrock PN[1405] Carb
Carburetor Center-to-Center Dimensions = 6-7/16 in

from

$322.99

Edelbrock part #2703 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thro

Product Features:

Idle-5500 RPM Range
Dual Plane Type-4150 Style Flange
3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
Satin Finish
Non-EGR W/ Oil Fill Tube

from

$927.99

The Edelbrock #609019 Performer cylinder head is designed for 302, 327, 350 and 400 cid small-block Chevy engines up to 1986. This cylinder head includes your choice of 64cc (In order to retain stock compression ratio on 1970 and earlier small-blocks) or

from

$1084.99

The Edelbrock #604919 Performer Bare High Compression Cylinder Heads are designed for Big-Block Chevy Oval Port V8 applications. These Edelbrock Performer Series Cylinder heads are 50-state street legal and provide outstanding performance from Idle-5,500

Product Features:

High Compression
100cc Combustion Chamber Volume
290cc Intake/110cc Exhaust Runner Volume
2.19 in. Intake/1.88 in. Exhaust Valve Diameter
0.562 in. Deck Thickness

1970 Chevrolet Townsman Performance Engines

More 1970 Chevrolet Townsman Performance Engines

Essential 1970 Chevrolet Townsman Performance Engines

Competition Cams – CAMSHAFT, SBC 284 XTREME ENERGY HYDRAULIC 1 EA (Part No.12-250-3)

Edelbrock – TIMING CHAIN (Part No.7844)

B & M – Tork Master 3000 (Part No.20402)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4375)

Mr. Gasket – Ultra Seal: Cylinder Head Bolts (Part No.941G)

Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1010)

Weiand – Action +Plus; Water Pump (Part No.9212P)

Mr. Gasket – Precision Timing Tape (Part No.1591)

Mr. Gasket – Rear Main Seal Gasket (Part No.1960)

Mr. Gasket – Water Neck (Part No.9141G)

FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1802)

Edelbrock – Performer-Plus Camshaft Kit for 1957-86 Small-Block Chevrolet (Part No.2103)

Mr. Gasket – Valve Cover Gasket Set (Part No.585G)

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1075)

Edelbrock – Pushrod Set for S/B Chevy (Part No.9629)

Edelbrock – Sure Seat Valve Springs for Big-Block Chevy 396-402-427-454 V8 (Part No.5862)

Edelbrock – Front Timing Cover Gasket Set #6998 For Big-Block Chevy, With Front Seal (Part No.6998)

Edelbrock – Torker-Plus Camshaft Kit for 1957-1986 Small-Block Chevy 283-400 V8 (Part No.5002)

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9730)

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9721)

Edelbrock – Intake Manifold Gasket for 1965-1990, Oval port 396-402-454 B/B Chevy (Part No.7203)

Mr. Gasket – Ultra Seal: Intake Gasket (Part No.5818)

Edelbrock – part #54201 Big-Block Chevy C-66-O polished intake manifold (Part No.54201)

Edelbrock – Performer EPS Intake Manifold w/ Oil Fill Tube for 1955-86 Small-Block Chevy (Part No.2703)

Edelbrock – Performer Small-Block Chevy Cylinder Head 64cc Flat Tappet Polished (Part No.609019)

Edelbrock – XX Performer Big-Block Chevy Oval Port Hydraulic Flat Tappet Cam Polished (Part No.604919)

Popular 1970 Chevrolet Townsman Performance Engines Categories

1970 Chevrolet Townsman Performance Engines

Performance Engines Brands To Make Your 1970 Chevrolet Townsman Last

Popular B & M Performance Engines

Top 1970 Chevrolet Townsman Performance Engines from Mr. Gasket

FAQs for 1970 Chevrolet Townsman Performance Engines

What are the most purchased Performance Engines for the 1970 Chevrolet Townsman?

What are the top-rated 1970 Chevrolet Townsman Performance Engines?

More Popular Parts for All Makes