1969 Jeep Wagoneer Drivetrains

Below you will find various in-demand Jeep Drivetrains, components and accessories for your 1969 Wagoneer. Advance Auto Parts has popular Wagoneer parts like Spindles, Drive Shafts and Axles, Universal Joints and more. You’ll also find aftermarket and OEM Drivetrains for other Wagoneer model years including 1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990 and more. Select a category of 1969 Jeep Wagoneer Drivetrains below and start saving instantly.

Please Select your Vehicle to See Exact Fit Parts

Popular 1969 Jeep Wagoneer Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

Wheel Hub Seal Kits

U-Joints

Differential Open Unit and Components

Differential Covers

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Differential Bearings

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

Differential Pinion Pilot Bearings

Spindle Support Struts

U-Joint Centering Yokes

Differential Cover Bolts

Transfer Case Output Shaft Seals

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Transfer Case Overhaul Kits

Differential Clutch Packs

Rear Axle Shaft Bearings

Differential Ring and Pinions

U-Joint U-Bolt Kits

Differential End Yokes

Spindle Lock Nuts

Differential Lock Assemblies

Differential Air System Seal Housings

Differential Spools

Differential Carrier Bearings

Front Differential Cover Gaskets

Rear Housing Cover Gaskets

Transfer Case Output Shaft Bearings

Differential Pinion Bearing Kits

Transfer Case Differential Bearings

Drive Shaft Seals

Differential Seals

Complete Differentials

Bearing and Seal Overhaul Kits

Differential Ring Gear Bolts

Bearing Race Drivers

Spindle Lock Nut Thrust Washers

Differential Carrier Bearing Shims

Input Shaft Seals

Spindle Retainers

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Cross Pins

Mounting Adapter Seals

Differential Housing O-Rings

Differential Side Gear Thrust Washers

Differential Pinion Bearing Baffles

Differential Pinion Gear Thrust Washers

Differential Drive Pinion Oil Deflectors

Differential Carrier Bolts

Spindle Washers

Limited Slip Differential Assemblies

Differential Clutch Pack Clips

Differential Lock Washers

Axle Pinion Repair Sleeves

Transfer Case Shift Rail Spring

Essential Drivetrains for 1969 Jeep Wagoneers

from

$5.99

Product Features:

Floater roll pin
Fits Dana Spicer 44 and Chrysler 8.75″
Powr Lok positraction only

from

$253.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 27
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$3.29

This spindle nut retainer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$182.99

Replacement redi-sleeve yoke saver for Dana 25, Dana 27, Dana 30, Dana 44, Dana 50 .Yukon Mighty seal.

Product Features:

Pinion Redi-sleeve
Fits Dana Spicer 25, 27, 30, 4 and 50

from

$55.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

from

$30.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$31.49

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for the repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$8.99

Crown Automotive continues to be the leader in quality replacement parts for Jeep(R) vehicles. Crown has the largest stock of replacement parts for Jeep(R) vehicles, including factory discontinued parts. In fact, many of the older Jeeps are still on (and off) the road thanks to Crown parts. The Crown line consists of axle, body, brake, clutch, cooling, driveline, electrical, engine, exhaust, fuel, steering, suspension, transmission And transfer case components. Crown Automotive also offers an exclusive line of component kits And accessory products.

Product Features:

Leading Manufacturer Of Quality Replacement Parts For Jeep
Meets Standards For Quality
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
Improve The Performance
Easy Installation

from

$1566.99

21 Piece bearing race driver set. (Box wt: 140lbs) No return.

Product Features:

Bearing race driver set
21 pieces
All steel construction

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$6.99

Product Features:

Oil baffle for Dana Spicer 44

from

$13.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$12.49

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$414.99

Yukon billet replacement yoke for Dana 60 and 70 with 29 spline pinion and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60 and 70
29 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
U-bolt style

from

$7.99

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$151.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits Dana Spicer 60 rear
Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.

from

$2.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

Meets or exceeds OE specifications

from

$10.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$9.99

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
1/2″ head

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$7.99

Product Features:

Outer stub thrust washer
Fits Dana Spicer 30 and 44

from

$15.29

Product Features:

RIGHT TYPE: Needle bearings are application-specific for the repair occasion, using either caged or full complement designs
PREMIUM MATERIALS: Precision manufactured using high-quality materials for outstanding durability and performance
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$276.99

Set-up carrier bearing kit (2 bearings, no races) for Dana 60 and 70. 387A. No return.

Product Features:

Set up bearing kit
Fits Dana Spicer 60
Easily slips on and off carrier journals to allow for easier carrier shim adjustment

from

$31.99

Product Features:

Driven plate
Fits Dana Spicer 44 Powr Lok

from

$287.99

Yukon round replacement yoke companion flange for Dana 60 and 70. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60 and 70
29 spline
5.00″ O.D.
8 x 4.25″ bolt pattern
Round companion flange

from

$1302.99

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years.

Product Features:

Fits Dana Spicer 44 with 30 spline axles
3.73 and down ratio only
Forged case and 8620 internals for added strength
Works with a variety of air delivery systems
Assembled in the USA

from

$359.99

Aluminum Girdle replacement cover for Dana 44 TA HD.

Product Features:

Fits standard rotation Dana Spicer 44
Aluminum girdle cover

from

$399.99

Yukon positraction internals for Dana 44 Dura Grip posi, 30 spline. Does not include clutches. Does NOT fit Trac Loc or Powr Lok. Fits Dura Grip ONLY.

Product Features:

Spider gear kit
Fits Dana Spicer 44 with Dura Grip positraction
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Upgrade your 1969 Jeep Wagoneer with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1969 Jeep Wagoneer, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Jeep or enhancing its overall performance, Drivetrains are key to keeping your Wagoneer functioning at its best. At Advance Auto Parts, we offer a wide selection of 251 Drivetrains for the 1969 Jeep Wagoneer, designed to meet your needs without breaking the bank. From Spindle replacements to Drive Shafts and Axles upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1969 Jeep Wagoneer at great prices. Our Drivetrains inventory for this model ranges from just $1.99 to $1,566.99, with an average price of $212.62. Our 251 Drivetrains in stock come from 13 trusted brands, so you’re sure to find the right part for your 1969 Jeep Wagoneer without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1969 Jeep Wagoneer, we stock popular OEM and aftermarket Drivetrains from top names like Moog, National, Driveworks, and more. Moog Drivetrains start at just $23.99 and boast an impressive 4.5 stars average rating from customers. National and Driveworks also bring quality to the table, with Drivetrains available starting at $6.99, and at an average 4.3 stars rating. With 1,994 customer reviews and counting, our 1969 Jeep Wagoneer Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1969 Jeep Wagoneer is always ready to roll. We’re committed to providing you with everything you need to keep your Wagoneer in top shape, all in one place. Start shopping confidently below for your 1969 Jeep Wagoneer!

Best-Selling Spindles for 1969 Jeep Wagoneers

Enhance the driving experience in your Jeep with 12 quality Spindle components, starting at $2.99.

show more show less

from

$8.99

Spindle nut retainer, 2.030″ I.D., 8 bent over tabs. This replaces Spicer part number 33733.

Product Features:

Spindle nut retainer for Dana Spicer 60, 70, 70U and 70HD
2.030″ I.D.
8 bent over tabs

from

$37.99

Spindle nut kit for Dana 30, Dana 44 & GM 8.5″. Not CJ or Scout. This replaces Spicer part number 28068X.

Product Features:

Spindle nut kit for Dana Spicer 30, Dana Spicer 44 and GM 8.5″
Will not fit Jeep CJ or Scout applications

from

$26.99

Spindle nut for Dana 60 & 70, 1.940″ I.D., with plastic ring. This replaces Spicer part number 39695.

Product Features:

Spindle nut
Fits Dana Spicer 60 and 70
1.940″ I.D.
Has plastic inner ring

from

$10.99

Spindle nut retainer for Dana 60 & 70, 1.830″ I.D., 10 outer tabs. This replaces Spicer part number 30637.

Product Features:

Spindle nut retainer for Dana Spicer 60, 70, 70U and 70HD
1.830″ I.D.
10 outer tabs

from

$4.29

This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$27.99

Spindle nut, 2.065″ I.D., six slots. This replaces Spicer part number 36635.

Product Features:

Spindle nut
6 slots
2.065″ I.D.

from

$17.79

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$15.99

Spindle nut for Dana 60, 1.750″ I.D., 6 sided. This replaces Spicer part number 30636.

Product Features:

Spindle nut
Fits Dana Spicer 60
6 sides
1.750″ I.D.

from

$12.99

Crown Automotive continues to be the leader in quality replacement parts for Jeep(R) vehicles. Crown has the largest stock of replacement parts for Jeep(R) vehicles, features factory discontinued parts. In fact, many of the older Jeeps are still on (and off) the road thanks to Crown parts. The Crown line consists of axle, body, brake, clutch, cooling, driveline, electrical, engine, exhaust, fuel, steering, suspension, transmission And transfer case components. Crown Automotive also offers an exclusive line of component kits And accessory products.

Product Features:

Hazardous Free Material
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
Designed And Built To OEM Specs
Direct-Fit Replacement

from

$6.99

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$3.99

Crown Automotive offers the largest line of replacement parts for Jeep (R), as well as a growing line of parts for Chrysler and Dodge vehicles. Our applications features Axle, Body, Brake, Clutch, Cooling, Electrical, Engine, Fuel, Lamps, Mirrors, Steering, Suspension, Transmission and Wiper.

Product Features:

Crown Automotive Is The Premiere Manufacturer And Distributor Of Quality Replacement Parts
Hazardous Free Material
Offers OE Fit And Function
Easy To Install

from

$2.99

Crown Automotive Is The Premiere Manufacturer And Distributor Of Quality Replacement Parts
Hazardous Free Material
Offers OE Fit And Function
Easy To Install

Most Popular 1969 Jeep Wagoneer Drive Shafts and Axles

Customize your Jeep with 13 Drive Shafts and Axles products like Axle Shaft Seals, Axle Shaft Universal Joints, and Rear Axle Shaft Bearings, all priced under $414.99.

show more show less

from

$38.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$14.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$51.99

Product Features:

Journal cross is engineered with a solid cold-formed body to ensure better wear and overall strength.
Bearing cups are heat treated for strength; precision-ground and case-hardened for durability.
Multi-lip seal keeps grease in and contaminants out, and gets maximum retention in a wider range of environments.
Thrust washers eliminate metal-to-metal contact, prevent wear and lower the overall operating temperature.

from

$30.49

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$41.99

2.00″ OD replacement inner axle seal for Dana 30 and 27.Yukon Mighty seal.

Product Features:

Inner axle seal
Fits Dana Spicer 27 and 30

from

$10.99

Leading Manufacturer Of Quality Replacement Parts For Jeep
Meets Standards For Quality
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
Easy Installation

from

$7.99

Product Features:

Pinion yoke dust shield
Fits Dana Spicer 60 and 70

from

$14.99

Design type: springless; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$414.99

Fits Dana Spicer 60 and 70
29 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
U-bolt style

from

$271.99

Yukon replacement yoke for Dana 60 and 70 with a 1330 U/joint size. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects. This is a u/bolt style yoke.

Product Features:

Fits Dana Spicer 60 and 70
29 spline
1330 u-joint size
Outside snap ring design
3.625″ snap ring span
1.062″ cap diameter
U-bolt style

from

$233.99

Yukon replacement yoke for Dana 44-HD, 60, and 70 with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60 and 70
29 spline
1310 u-joint size
Outside snap ring design
3.219″ snap ring span
1.062″ cap diameter
Strap style

from

$219.99

Yukon replacement yoke for Dana 60 and 70 with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60, 70, 70U and 70HD
29 spline
1350 u-joint size
3.625″ snap ring span
1.188″ cap diameter
Outside snap ring design
U-bolt style

from

$182.99

Replacement redi-sleeve yoke saver for Dana 25, Dana 27, Dana 30, Dana 44, Dana 50 .Yukon Mighty seal.

Product Features:

Pinion Redi-sleeve
Fits Dana Spicer 25, 27, 30, 4 and 50

Top Picks for 1969 Jeep Wagoneer Universal Joints

Upgrade Jeep Wagoneers with top-quality Universal Joints parts, including 42 OEM and aftermarket selections for your 1969 model.

show more show less

from

$31.99

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$23.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 353, 354, 361, 369 & 497
Fits 1-1/16″ bearings

from

$15.99

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$36.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$43.99

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$26.99

For U-Joints 315G, 317, 319 & 457
Contains two 1-1/2″ bolt center clamps and four 1/4-28 x 5/8″ cap screws

from

$35.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE – Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN – Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR – Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE – Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$33.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$41.49

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$34.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$35.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$7.49

This universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

Direct replacement – this universal joint U-bolt kit is designed to match the original components required to repair and resecure universal joints on specified vehicles
Ideal solution – this kit is a reliable replacement for original components that are missing or have failed due to fatigue
Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$45.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$45.99

from

$59.99

Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.

from

$34.99

1310 U-bolts, 5/16″ x 1-3/8″ Dana 30, Dana 44, 8.2″, 12P, 12T, VET, Model 20.

Product Features:

u-joint u-bolt kit
Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
1310 u-joint size
Includes two u-bolts and four nuts

from

$33.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$16.99

1350 & 1410 U/joint U-bolts, 3/8″ X 1-11/16″, kit.

Product Features:

u-joint u-bolt kit
Fits 1350 and 1410 u-joint size
Includes two u-bolts and four nuts

from

$78.99

Yukon 1350 to 1410 conversion u/joint.

from

$33.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$109.99

Yukon 1310 to Mechanics 3R adapter U/Joint.

from

$63.99

Yukon 1350 Lifetime Series U/Joint. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring.

from

$61.99

Yukon 1330 Dual-size cap U/Joint. 3.625″ snap ring span. One set of caps is 1.125″ in diameter and the other is 1.062″. Outside snap ring.

In-Demand Differentials for 1969 Jeep Wagoneers

Select from 166 premium Differentials parts for your 1969 Jeep Wagoneer, with prices ranging from $3.99 to $1,566.99.

show more show less

from

$35.99

Valvoline MaxLife Multi-Vehicle ATF is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life. Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi. Recommended for use in the following applications: GM DEXRON-II, DEXRON-III, DEXRON-VI, Ford MERCON LV, Toyota/Lexus Type T, T-II, T-IV, WS, Honda/Acura, ATF-Z1, Nissan/Infiniti Matic-D, Matic-J, Matric-K, Matic-S, Hyundai/Kia SP-II, SP-III, SP-IV, SPH-IV, BMW 7045E, ETL 8072B, LA2634, LT71141, Allison C-4, Mercedes Benz NAG-1, Volvo 1161521, 1161540, 97340, 1273.41, and VW/Audi G-052-025-A2, G-052-162-A1. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

Formulated with full-synthetic base oils and long life friction modifiers to help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$7.99

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$23.49

Design type: spring loaded; multi-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$505.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.Powertrax® = Extreme Traction Systems!

from

$168.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

DANA-44 LATE TIMKEN MASTER KIT

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$11.99

Replacement ring gear bolt for Model 35, Dana 25, 27, 30 & 44. 3/8″ x 24.

Product Features:

Ring gear bolt for Dana Spicer 25, 27, 30, 44 and AMC Model 35
3/8″ x 24 thread

from

$9.99

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
1/2″ head

from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$4.99

Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.

Product Features:

Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
1/2″ x 18 thread

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$4.99

Product Features:

Oil baffle for Dana Spicer 30, Dana Spicer 44 IFS, Dana Spicer 50, AMC Model 35 IFS

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$10.99

Dana 25, Dana 27, & Dana 30 side gear Thrust washer.

Product Features:

Side gear thrust washer for Dana Spicer 25, 27, 30 and AMC Model 35
1.560″ I.D.
Fits standard open differentials only

from

$13.99

Product Features:

Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80

from

$6.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

Pinion nut for Dana Spicer 25, 27, 30, 44, 50 and GM 7.75″
3/4″ x 16 thread

from

$17.99

Replacement pinion seal for Dana 25, Dana 27, Dana 30, D36, Dana 44, & Dana 50 .Yukon Mighty seal.

Product Features:

Pinion seal
Fits Dana Spicer 25, 27, 30, 40 and 50

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$16.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$19.99

Product Features:

Pinion preload shims for Dana Spicer 60 and 70U

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$137.99

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil

Most Sold 1969 Jeep Wagoneer Transfer Cases

Explore our best-selling Jeep parts for the 1969 Wagoneer among 17 OEM and aftermarket options starting from $1.99.

show more show less

from

$12.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$6.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$8.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$7.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$20.49

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$4.99

Product Features:

Design type: spring loaded; single-lip
Temperature range: -40 deg. F to 225 deg. F / -40 deg. C to 107 deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$18.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$24.99

Leading Manufacturer Of Quality Replacement Parts For Jeep
Meets Standards For Quality
Crown Automotive Has Consistently Maintained Its Commitment To Offering Only Quality Parts And Exceptional Service
Improve The Performance
Easy Installation

from

$33.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$31.49

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered and manufactured specifically for the repair environment
Unsurpassed quality you can trust
Validated for fit, form, and function

from

$14.99

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$7.79

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$149.99

TCaseBrg-SealKit

from

$27.99

Kit Includes Gaskets And Seals
Limited 12 Month Or 12,000 Mile Warranty

from

$22.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$8.99

Provides Leak Free Operation
Hazardous Free Material
Offers OE Fit And Function
Long-Lasting, Durable Crown Automotive Products

from

$1.99

Shift Rod Poppet Springs Keep The Shift Rail In Place
Jeep Manual Transmission Synchronizer Springs Are Quality Components From A Trusted Name In Jeep Replacement Parts
Designed And Built To OEM Specs
Easy To Install

Top-Rated Drivetrains Brands For Your 1969 Jeep Wagoneer

Shop for the best-rated brands offering Drivetrains and other products for your 1969 Jeep Wagoneers. Below you’ll find some of our best rated Drivetrains from Moog, National, and Driveworks, and more. Drivetrains from these brands that fit a 1969 Wagoneer start at just $6.99 and are rated as high as 4.5 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Moog 1969 Jeep Wagoneer Drivetrains

When it comes to maintaining or upgrading your 1969 Jeep Wagoneer, using quality Drivetrains is essential to ensure durability and a perfect fit. Moog ticks all of those boxes. We offer a wide selection of Moog Drivetrains, specifically designed for the 1969 Jeep Wagoneer. With over 3 Moog brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $23.99, with an average price of just $34.99. Plus, with over 9 customer reviews and an average rating of 4.5 stars, you can trust that our Moog Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $23.99

(4)

Universal Joint U-Bolt Kit

“I used these to replace the factory originals that had over 80K miles on a 1964 Chevelle Malibu. I had a strange click in the differential area and s”

from $43.99

(4)

Greaseable Super Strength Universal Joint

“Replaced all u joints frt axles frt drive and main shaft, time will tell.”

from $36.99

(1)

Greaseable Premium Universal Joint

“the u-joint itself fit fine however the grease fitting is too large for the hole provided in the u-joint. I had to enlarge the hole to fit the fitting”

Popular National 1969 Jeep Wagoneer Drivetrains

National auto parts is one of the highest quality Drivetrain brands in the market. Any 1969 Jeep Wagoneer owner should feel confident when installing genuine National parts in their vehicle. To ensure the best fit and performance for your 1969 Wagoneer, Advance Auto Parts carries a full inventory of 3 National Drivetrains. Plus you will be keeping your Jeep in peak condition while saving money because prices on these National Drivetrains range from $7.99 to $12.99, plus, with more than 11 customer reviews and an impressive 4.3 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from $7.99

(8)

Multi-Purpose Seal

“This seal should be located at the REAR of the TRANS, in FRONT of the TRANSFER CASE, BETWEEN trans and transfer case.”

from $8.99

(1)

Bearing Race

“Excellent quality and condition”

from $12.99

(2)

Multi-Purpose Seal

“Sealed tbe trams leak perfectly”

FAQs for 1969 Jeep Wagoneer Drivetrains

Which Drivetrains are best-sellers for 1969 Jeep Wagoneers?

Out of 251 Drivetrains that fit 1969 Jeep Wagoneers, the following parts are the top sellers:

Greaseable Premium Universal Joint (10086900) – $35.99
Non-Greaseable Super Strength Universal Joint (10087061) – $33.99
Greaseable Super Strength Universal Joint (10086944) – $41.49

What’s the price range for 1969 Jeep Wagoneer Drivetrains?

Drivetrain prices for the 1969 Jeep Wagoneer start at $1.99 and go up to $1,566.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1969 Jeep Wagoneer?

The average price for Drivetrains for the 1969 Jeep Wagoneer is $212.62. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Jeep Wagoneer model years?

Yes, we currently carry Drivetrains for 29 model years of Jeep Wagoneers between 1963 and 2025. Drivetrains are bought most frequently for the following model years: 1990, 1989, 1988, 1987, 1986, 1985, 1984, 1983, and 1982.

What are the cheapest Drivetrains for my 1969 Jeep Wagoneer?

The cheapest 1969 Jeep Wagoneer Drivetrains we carry in stock are:

Oem, For Use With Dana 300 Transfer Case/ Dana 20 Transfer Case (50074389) – $1.99
OE Replacement, Single (50074724) – $2.99
Dana 25 / 27 / 30 / 36 / 44 / 53 Pinion Nut Washer Replacement (11642796) – $3.99
Dana 44 JK / 60 / 70U Pinion Nut Washer Replacement (11643194) – $3.99
OE Replacement (50074712) – $3.99

What are the top-rated Drivetrains that fit the 1969 Jeep Wagoneer?

Out of 1,994 reviews by customers, our 1969 Jeep Wagoneer Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1969 Jeep Wagoneer and their top-rated products:

Differentials
- MaxLife Multi-Vehicle Automatic Transmission Fluid, 1 Gallon (8150020) – $35.99
- Axle Housing Cover Gasket Irregular Shaped 10 Bolt Hole Gasket (5185793) – $7.99
- Differential Pinion Seal (3270688) – $23.49
Universal Joints
- MaxLife Multi-Vehicle Automatic Transmission Fluid, 1 Gallon (8150020) – $35.99
- Axle Housing Cover Gasket Irregular Shaped 10 Bolt Hole Gasket (5185793) – $7.99
- Differential Pinion Seal (3270688) – $23.49

What types of Drivetrains do you sell for my 1969 Jeep Wagoneer?

As of 3/1/26, these are some of the most in-demand types of Drivetrains for a 1969 Jeep Wagoneer:

Can I get help with 1969 Jeep Wagoneer Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Jeep Drivetrains and more.

What is your return policy for Jeep Wagoneer Drivetrains?

Advance Auto Parts keeps returns simple. For new Jeep Wagoneer Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1969 Jeep Wagoneer Drivetrains

Yukon Gear – Replacement Floater Roll Pin For Dana 44 & 8.75" Chrysler Power Lok (Part No.33326)

Yukon Gear – Pinion Install Kit For Dana 27 Differential (Part No.13013)

Dorman – Spindle Nut M24-1.5 Hex Size 36mm (Sold by each) (Part No.615-149)

Yukon Gear – Replacement Redi-Sleeve Yoke Saver For Dana 25, Dana 27, Dana 30, Dana 44, Dana 50 (Part No.30222)

Spicer – Universal Joint (Part No.5-760X)

National – Shaft Repair Sleeve (Part No.99125)

Felpro – Transfer Case Gasket Set (Part No.TS 3181 A)

Crown Auto Jeep Replacmnt – Model 20 Rear Axle, Rubber (Part No.J3208474)

Yukon Gear – Bearing Race Driver Set, 21 Piece (Part No.56030)

Yukon Gear – 3 Qt – Penzoil 80W90 Conventional Gear Oil (Part No.15002)

Yukon Gear – Replacement Oil Baffle For Dana 44 (Part No.33000)

National – Bearing Race (Part No.02820)

Felpro – Axle Housing Cover Gasket (Part No.RDS 13889)

Yukon Gear – Billet Replacement Yoke For Dana 60 And 70 With 29 Spline Pinion And A 1350 U/Joint Size (Part No.41138)

Driveworks – Oil Seal (Part No.S-2146)

Yukon Gear – Minor Install Kit For Dana 60 And 61 Differential (Part No.12026)

Pro-King – Differential Crush Sleeve (Part No.721A034)

National – Bearing Race (Part No.JLM104910)

Yukon Gear – Dana 25, 27, 30, 44, Model 20 And Model 35, GM 7.5", 8.2", 8.5", 12P, 12T, C9.25 Rear Cover Bolt (Part No.33286)

Yukon Gear – The Carrier Bearing Puller (Part No.56072)

Yukon Gear – Outer Stub Thrust Washer For Dana 30 & 44 (Part No.33534)

National – Multi-Purpose Bearing (Part No.B-228)

Yukon Gear – Set Up Bearing (Part No.56039)

Yukon Gear – Powr Lok Flat Driven Plate For Dana 44 (Part No.16173)

Yukon Gear – Round Replacement Yoke Companion Flange For Dana 60 And 70 (Part No.41033)

Yukon Gear – Zip Locker For Dana 44 With 30 Spline Axles, 3.73 & Down (Part No.34018)

Yukon Gear – Aluminum Girdle Replacement Cover For Dana 44 Ta HD (Part No.32110)

Yukon Gear – Positraction Internals For Dana 44 Dura Grip Posi, 30 Spline (Part No.16168)

Yukon Gear – Spindle Nut Retainer, 2.030" I.D., 8 Bent Over TABS (Part No.33480)

Yukon Gear – Spindle Nut Kit For Dana 30, Dana 44 & GM 8.5" – Not CJ Or Scout (Part No.33475)

Yukon Gear – Spindle Nut For Dana 60 & 70, 1.940" I.D., With Plastic Ring (Part No.33486)

Yukon Gear – Spindle Nut Retainer For Dana 60 & 70, 1.830" I.D., 10 Outer TABS (Part No.33477)

Dorman – Spindle Washer – I.D. 41.4mm O.D. 65.0mm Thickness 1.7mm (Sold by each) (Part No.618-058)

Yukon Gear – Spindle Nut, 2.065" I.D., Six Slots (Part No.33484)

Dorman – Spindle Nut (Part No.615-126.1)

Yukon Gear – Spindle Nut For Dana 60, 1.750" I.D., 6 Sided (Part No.33476)

Crown Auto Jeep Replacmnt – Dana 25/ 27/ 30 Axle (Part No.J0649783)

Dorman – Spindle Washer – I.D. 1 In.-5/8 In. O.D. 2-3/16 In. Thickness 3/32 In. (Sold by each) (Part No.618-045)

Crown Auto Jeep Replacmnt – OE Replacement (Part No.JA000867)

Crown Auto Jeep Replacmnt – OE Replacement, Single (Part No.JA000865)

Spicer – Universal Joint (Part No.5-1310X)

Driveworks – Oil Seal (Part No.S-9912)

Spicer – Axle Shaft Universal Joint, Non-Greaseable, 1310 Series, Wheel Joint ISR (Part No.5-260X)

National – Shaft Repair Sleeve (Part No.99125)

Yukon Gear – 2.00" OD Replacement Inner Axle Seal For Dana 30 And 27 (Part No.30050)

Crown Auto Jeep Replacmnt – OE Replacement (Part No.J0914802)

Yukon Gear – Pinion Yoke Dust Shield For Dana 60 & 70 (Part No.33441)

National – Drive Axle Shaft Seal (Part No.40576S)

Yukon Gear – Billet Replacement Yoke For Dana 60 And 70 With 29 Spline Pinion And A 1350 U/Joint Size (Part No.41138)

Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1330 U/Joint Size (Part No.41025)

Yukon Gear – Replacement Yoke For Dana 44-HD, 60, And 70 With A 1310 U/Joint Size (Part No.41022)

Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1350 U/Joint Size (Part No.41027)

Yukon Gear – Replacement Redi-Sleeve Yoke Saver For Dana 25, Dana 27, Dana 30, Dana 44, Dana 50 (Part No.30222)

Spicer – Universal Joint, Greaseable 1310 Series OSR (Part No.5-153X)

MOOG Driveline Products – Universal Joint U-Bolt Kit (Part No.329-10)

Driveworks – Universal Joint (Part No.DW-315G)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.317)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.378)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.318-10)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.369)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.269)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.280)

Driveworks – Universal Joint (Part No.DW-365)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.315G)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.365)

Dorman – Help – U-Joint Bolt Kit (Part No.81008)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.513)

Spicer – Universal Joint (Part No.5-789X)

Yukon Gear – 1310 To 1330 Adapter U/Joint (Part No.42005)

Yukon Gear – Dana 44, 8.2", 12P, 12T, Vet, And Model 20 U-Bolts (Part No.41198)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.505)

Yukon Gear – 1350 & 1410 U/Joint U-Bolts, 3/8" X 1-11/16", Kit (Part No.41190)

Yukon Gear – 1350 To 1410 Conversion U/Joint (Part No.42006)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.361)

Yukon Gear – 1310 To Mechanics 3R Adapter U/Joint (Part No.42013)

Yukon Gear – 1350 Lifetime Series U/Joint (Part No.42021)

Yukon Gear – 1330 Dual-Size Cap U/Joint (Part No.42017)

Valvoline – MaxLife Multi-Vehicle Automatic Transmission Fluid, 1 Gallon (Part No.773775)

Felpro – Axle Housing Cover Gasket Irregular Shaped 10 Bolt Hole Gasket (Part No.RDS 6629)