1969 Ford Thunderbird Differentials

Yukon Gear & Axle spider gear kits feature higher quality materials and better manufacturing techniques than OEM to ensure a longer lasting spider gear set. Kit delivers everything needed for a complete and proper spider gear set replacement.

Product Features:

• Spider gear kit
• Fits Ford 9″ open differential with 31 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. This unit requires the use of a 3.250″ dropout. Use carrier bearing/race numbers LM104949/LM104911. The Yukon Grizzly locker uses 8620 internals and a patented design to provide maximum strength and reduce common failures. Assembled in the USA! This unit has been approved for competition in NASCAR National & Touring series. This is a race unit designed for extreme off road use or racing. All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

• Fits Ford 9″ with 31 spline axles
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA
• Aggressive design for racing applications only

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND.

8.8″ Ford cover gasket.

Product Features:

• Cover gasket
• Fits Ford 8.8″

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

Yukon Gear and Axle manufactures a complete line of general replacement and performance series of pinion yokes for many street, racing, and heavy-duty off-road applications.

Product Features:

• Fits Ford 8.8″
• 30 spline
• Round companion flange
• 4.3″ O.D.

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion nut
• Fits Ford 9″ with 35 spline pinion

Yukon Gear & Axle offers a full line of top quality differential tools to save time and money.

Product Features:

• Fits M802011 race
• All-steel construction
• For accurate installation of bearing races

Yukon shim kits are precision machined and tailored for each individual application to ensure you have the right shims for every set up.

Product Features:

• Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
• Interlocking design makes installation much easier

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Trac Loc spring plate for Ford 8″ and 9″

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool
• Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

Yukon Mighty Seals use the latest design and manufacturing technologies to produce a precision fit that seals tight and lasts for years to come.

Product Features:

• Pinion support O-ring
• Fits Ford 9″

Product Features:

• Brand may vary by location

Yukon Gear & Axle dropouts are heavy duty. They feature upgraded nodular iron construction and a larger-than-OEM design to provide unrivaled strength and reliability in racing and off-road applications.

Product Features:

• Side adjuster lock bolt

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Ford 9″ with LM603011 carrier races and Daytona pinion support
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, pilot bearing, thread locker, marking compound with brush and gasket.

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Clutch guide
• Fits Ford 8″ and 9″

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

• Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

Product Features:

• Ford 7.5″, 8.8″ Ring Gear Bolt

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a Limited warranty against defect.

Product Features:

• Fits Ford 8.8″ with 31 spline axles and 7/8″ cross pin shaft
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

Yukon heavy duty pinion supports feature upgraded materials and a larger design than OEM to provide heavy duty strength in racing and off-road applications

Product Features:

• Fits Ford 9″ with 28 spline pinion
• Larger inner pinion bearing reduces gear deflection under high load
• Nodular iron
• Does not include races

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Side gear thrust washer for Ford 8.8″
• 0.750″ diameter cross pin shaft applications only

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

Product Features:

• NODULAR HOUSING 9″ FORD 3.062 BORE STRANGE # N1905

Yukon Gear & Axle spider gear kits feature higher quality materials and better manufacturing techniques than OEM to ensure a longer lasting spider gear set. Kit delivers everything needed for a complete and proper spider gear set replacement.

Product Features:

• Spider gear kit
• Fits Ford 8.8″ with 31 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
• 0.875″ cross pin shaft diameter

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Manufactured with premium-grade steel, National taper bearing sets feature crowned raceways and rollers to ensure even load distribution.

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Yukon Pinion Installation Kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings and races can be reused. This kit features Timken bearings and races along with high-quality seals and small parts. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your gear set.

Product Features:

• Fits Ford 7.5″
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.