from

$489.65

As the basis for a standardized ATE concept for future tandem master cylinders, ATE has developed a new plunger generation which has many technical enhancements and advantages.

Product Features:

Short closing paths
Low volume uptake
High efficiency
Low throttling / after-suction resistance
Low pressure differential between primary and secondary circuits
Good bleedability
Cr6-free surfaces for vehicles built from July 2007 (as required by law)
Central valve version suitable for ABS
Compact design – ideal for installation in small spaces
Reduced weight – by roughly 20% compared to conventional central valve technology
Fewer components – almost half as many as compared to conventional technologies
Modular system – diameters from 14.29 to 31.75mm and strokes up to 46mm
Low volume uptake – minimized elastic deformations due to smaller seals
Sealing cups supported in the housing – robustness against soiling and wear; longer life
Cr6-free surfaces for vehicles built from July 2007 (as required by law)

from

$493.32

As the basis for a standardized ATE concept for future tandem master cylinders, ATE has developed a new plunger generation which has many technical enhancements and advantages.

Product Features:

Short closing paths
Low volume uptake
High efficiency
Low throttling / after-suction resistance
Low pressure differential between primary and secondary circuits
Good bleedability
Cr6-free surfaces for vehicles built from July 2007 (as required by law)
Central valve version suitable for ABS
Compact design – ideal for installation in small spaces
Reduced weight – by roughly 20% compared to conventional central valve technology
Fewer components – almost half as many as compared to conventional technologies
Modular system – diameters from 14.29 to 31.75mm and strokes up to 46mm
Low volume uptake – minimized elastic deformations due to smaller seals
Sealing cups supported in the housing – robustness against soiling and wear; longer life
Cr6-free surfaces for vehicles built from July 2007 (as required by law)

from

$15.99

CARDONE Master Cylinder Bench Bleeder Tool cuts typical bleeding procedures in half and is a more effective way to purge the brake system of air than other bleeding procedures. This handy, innovative tool is a must, just as bench bleeding is for removing all the air from your brake system, allowing you to spend less time in the garage, and more time on the road.

Product Features:

Each unit is 100% new, providing consistent performance when servicing your brake system
Easy to transfer for on-the-spot master cylinder bleeding
Fluid measurements clearly displayed on each unit in both ounces and milliliters for convenience
Easy to clean to ensure no cross contamination
Durability for long lasting performance

from

$697.81

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

OE quality direct fit application.
Friction Ready
Corrosion inhibiting protection
Ensures long life and maximum performance
Natural exterior finish

from

$728.74

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

OE quality direct fit application.
Friction Ready
Corrosion inhibiting protection
Ensures long life and maximum performance
Natural exterior finish

from

$726.83

100% New Caliper – Manufacturer recommends replacing calipers in pairs. With innovative fixed and floating calipers in aluminum and nodular cast iron, ATE is Europe’s market leader. And there is a good reason for that: during development, ATE simulates operational stresses in terms of braking load, vibration, corrosion and wear in extensive series of trials. This means that every basic safety-relevant function is ensured, the sealing of the hydraulic system as much as the venting function of the piston (roll-back), the return (knock-back) function, or the function of the housing/pad guides. ATE original brake calipers are supplied ready-to-install: rear-axle calipers with handbrake are usually pre-filled and preset. This permits simple and correct bleeding in the vehicle.

Product Features:

OE quality direct fit application.
Friction Ready
Corrosion inhibiting protection
Ensures long life and maximum performance
Natural exterior finish

from

$19.99

Each Carquest Premium brake hose assembly is precision engineered to match the original fit and includes brackets, grommets, molded plastic guards, wire clips and protective sleeves as required to ensure that all wearable parts are restored to original condition. Carquest Premium brake hoses meet or exceed Department of Transportation (DOT), Federal Vehicle Safety Standards (FMVSS 106) and Society of Automotive Engineers (SAE J1401) standards to ensure a reliable and long-lasting repair.

Product Features:

Brake hoses with banjo end fittings include new copper washers to ensure proper sealing
Tensile minimum load holds up to 1800 N
All end fittings are electroplated with eco-friendly material that delivers superior corrosion and rust resistance
Designed based on requirements and testing of SAE J1401, resulting in high quality brake hoses
Every brake hose is subjected to a high-pressure quality assurance test before leaving the factory, ensuring trouble-free installation and operation
Brand may vary by location

from

$43.48

Brake Hose

from

$23.79

This automotive brake hydraulic hose was precision-engineered to match the fit, function and performance of the original brake hose on specific vehicles and positions to ensure safe, long-lasting durability as part of a complete brake repair.

Product Features:

Ideal replacement – precision-engineered to match the performance of the original brake hose on specific vehicles
Position-specific – manufactured to precise measurements to provide an exact fit and easy installation
Quality assured – materials tested to exacting government-regulated safety and durability standards
Durable design – made with EPDM rubber and specially coated, corrosion-resistant fittings
Brand may vary by location

from

$111.99

Carquest Wearever rotors meet or exceed original equipment specifications while delivering superior stopping power. Carquest Wearever rotors are manufactured with proper harmonic design and non-directional finish that eliminate noise and enhance pedal feel. Our rotors are designed to effectively dissipate heat, helping to eliminate brake fade and increase the life of your pads and rotors. Carquest Wearever rotors are designed for long-lasting and quiet braking with superior performance.

Product Features:

Meets or exceeds OE design for superior stopping power
Exceeds ISO manufacturing guidelines (International Organization for Standardization)
Matches OE vane size for proper cooling
Optimal metallurgy and casting thickness to preventing warping
Air gap eliminates brake fade and increases pad life
Non-directional finish decreases break-in time

from

$237.75

The Sebro coated brake disc is an OE-Quality replacement that is manufactured to withstand the higher demands of braking extremes from today’s high performance European vehicles. For the sustainable improvement of corrosion protection and also for good looking our break discs are silver grey coated in the pot- and outer diameter area. By the automatic coating process a high quality with steady coating thickness is guaranteed. In the uncoated areas all components are provided with suitable corrosion protection.

Product Features:

OE-Equivalent and Direct fit Application
high carbon content disc
Protective coating that resists corrosion
Provides a higher friction coefficient.
Resistant to vibrations and noise.
Improved thermal efficiency

from

$195.35

Brake Disc

from

$38.96

FTE Disc Brake Caliper Repair Kit contains the components necessary for repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

Guaranteed factory fit to original equipment specifications
Meets or exceeds original equipment factory safety standards

from

$46.21

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

Guaranteed factory fit to original equipment specifications
Meets or exceeds original equipment factory safety standards

from

$26.23

ATE Disc Brake Caliper Repair Kit contains the components necessary for piston seal repair of the Disc Brake Caliper. All of the rubber components are of high-quality EPDM compound for resistance to glycol-based brake fluid.

Product Features:

Guaranteed factory fit to original equipment specifications
Meets or exceeds original equipment factory safety standards

from

$1.18

The Elring Distributor O-Ring is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

Premium Original Equipment replacement
Provides performance and dependability
Manufactured to meet OE specifications

from

$67.99

The Power Stop Z17 Evolution Plus ceramic brake pads feature a ceramic formula designed to maximize stopping power while reducing brake dust & eliminating noise. Using OE positive mold technology along with a thermal scorched pad surface, Z17 pads maintain consistent wear and performance while ensuring a fast break-in. Hardware is included with the Z17 brake pads making it easier to complete your brake job. The Power Stop Z17 Evolution Plus ceramic brake pads are an affordable stock replacement for all vehicles.

Product Features:

Low-dust ceramic formula designed to maximize stopping power and keep wheels clean
Positive mold technology for consistent wear and performance
Thermal scorched pad surface for a fast break-in
Chamfered and slotted to ensure noise free braking
Powder coated backing plate resists rust and corrosion to provide extended pad life
Multi-Layer rubberized shims provide virtually noise-free braking
Includes Premium hardware for easy installation

from

$61.99

The Power Stop Z16 Evolution ceramic brake pads feature a ceramic formula designed to maximize stopping power while reducing brake dust & eliminating noise. Using OE positive mold technology along with a thermal scorched pad surface, Z16 pads maintain consistent wear and performance while ensuring a fast break-in. The Z16 Evolution ceramic brake pads are an affordable stock replacement for all vehicles.

Product Features:

Low-dust ceramic formula designed to maximize stopping power and keep wheels clean
Positive mold technology for consistent wear and performance
Thermal scorched pad surface for a fast break-in
Chamfered and slotted to ensure noise-free braking
Powder coated backing plate resists rust and corrosion to provide extended pad life
Multi-Layer rubberized shims provide virtually noise-free braking

from

$266.88

This part matches Original Equipment (OE) quality specifications which means that it is at least as good if not better than the original part the manufacturer supplied the car with. TRW has introduced Cotec – an innovative coating for its brake pads. Independent tests have proven that Cotec achieves significantly shorter stopping distances than the brake pads of major competitors or even OE, for the first stops after leaving a garage following a brake pad change. In the normal bedding in process there is a period, known as the green behavior of the pad, which occurs at the start of the bedding in process where the friction co-efficient is lower than usual. Drivers can find it difficult to adjust to the difference in performance during these first stops. TRW Cotec brake pads address this issue by improving the contact between the brake disc and pad. The friction material is the most important part of a brake pad. All TRW’s brake pads contain the optimum mix of raw materials from rubber to graphite. TRW has made a significant investment over the years to ensure that we have the perfect mix – and we make it in-house. The ingredients ensure a stable friction coefficient and the safest braking performance in all temperatures, at all speeds and under all conditions. The backing plates used by TRW are designed, patented and produced in-house to OE specification. They are fitted to the friction material with a unique adhesive compound which can withstand high temperatures and resists extremely high shear strengths. TRW places great emphasis on noise reduction and its brake pads are fitted with high quality shims which act as a damper between the friction material and the brake caliper. TRW friction components are not only tested in our NVH (noise vibration harshness) laboratories and also on the road.

Product Features:

Include the OE specified shims.
Low noise and reduced vibrations.
Formulated to OE Specifications.
Superior friction qualities.
Organic blended compound.

from

$49.99

The Power Stop Z17 Evolution Plus ceramic brake pads feature a ceramic formula designed to maximize stopping power while reducing brake dust & eliminating noise. Using OE positive mold technology along with a thermal scorched pad surface, Z17 pads maintain consistent wear and performance while ensuring a fast break-in. Stainless steel hardware is included with the Z17 brake pads making it easier to complete your brake job. The Power Stop Z17 Evolution Plus ceramic brake pads are an affordable stock replacement for all vehicles.

Product Features:

Low-dust ceramic formula designed to maximize stopping power and keep wheels clean
Positive mold technology for consistent wear and performance
Thermal scorched pad surface for a fast break-in
Chamfered and slotted to ensure noise free braking
Powder coated backing plate resists rust and corrosion to provide extended pad life
Multi-Layer rubberized shims provide virtually noise-free braking
Includes Premium stainless-steel hardware for easy installation

from

$217.57

The Original Equipment brand brake disc is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.

Product Features:

OE-Equivalent and Direct fit Application
made of special cast iron with high carbon content
Provides a higher friction coefficient.
Resistant to vibrations and noise.
Contains the same high quality craftsmanship as the original equipment manufacturer.
Guarantees OE quality performance, durability and fitment.

from

$190.43

The Original Equipment brand brake disc is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.

Product Features:

OE-Equivalent and Direct fit Application
made of special cast iron with high carbon content
Provides a higher friction coefficient.
Resistant to vibrations and noise.
Contains the same high quality craftsmanship as the original equipment manufacturer.
Guarantees OE quality performance, durability and fitment.

from

$200.28

Brake Disc

from

$517.52

The Original Equipment brand brake disc is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.

Product Features:

OE-Equivalent and Direct fit Application
made of special cast iron with high carbon content
Provides a higher friction coefficient.
Resistant to vibrations and noise.
Contains the same high quality craftsmanship as the original equipment manufacturer.
Guarantees OE quality performance, durability and fitment.

from

$205.31

The Original Equipment brand brake disc is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.

Product Features:

OE-Equivalent and Direct fit Application
made of special cast iron with high carbon content
Provides a higher friction coefficient.
Resistant to vibrations and noise.
Contains the same high quality craftsmanship as the original equipment manufacturer.
Guarantees OE quality performance, durability and fitment.

from

$171.33

The Sebro coated brake disc is an OE-Quality replacement that is manufactured to withstand the higher demands of braking extremes from today’s high performance European vehicles. For the sustainable improvement of corrosion protection and also for good looking our break discs are silver grey coated in the pot- and outer diameter area. By the automatic coating process a high quality with steady coating thickness is guaranteed. In the uncoated areas all components are provided with suitable corrosion protection.

Product Features:

OE-Equivalent and Direct fit Application
high carbon content disc
Protective coating that resists corrosion
Provides a higher friction coefficient.
Resistant to vibrations and noise.
Improved thermal efficiency

from

$179.72

The Sebro coated brake disc is an OE-Quality replacement that is manufactured to withstand the higher demands of braking extremes from today’s high performance European vehicles. For the sustainable improvement of corrosion protection and also for good looking our break discs are silver grey coated in the pot- and outer diameter area. By the automatic coating process a high quality with steady coating thickness is guaranteed. In the uncoated areas all components are provided with suitable corrosion protection.

Product Features:

OE-Equivalent and Direct fit Application
high carbon content disc
Protective coating that resists corrosion
Provides a higher friction coefficient.
Resistant to vibrations and noise.
Improved thermal efficiency

from

$792.99

The Original Equipment brand brake disc is the ORIGINAL part, supplied in a plain box, with the car manufacturer’s logo on the part.

Product Features:

OE-Equivalent and Direct fit Application
made of special cast iron with high carbon content
Provides a higher friction coefficient.
Resistant to vibrations and noise.
Contains the same high quality craftsmanship as the original equipment manufacturer.
Guarantees OE quality performance, durability and fitment.