1968 Ford Bronco Performance Engines

Essential 1968 Ford Bronco Performance Engines

Mr. Gasket – Super Intake Manifold Bolts (Part No.6082)

Super Intake Manifold Bolts

from

$43.99
Super Intake Manifold Bolts

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1811)

PERFORMANCE OIL PAN GASKET SET

from

$30.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Ultra Seal: Harmonic Balancer Bolt/Washer Kit (Part No.7847)

Ultra Seal: Harmonic Balancer Bolt/Washer Kit

from

$38.49
Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.

Product Features:
  • Heat treated black oxide coated Grade 8 alloy steel
  • Thick parallel ground washer provides more accurate, uniform torque
  • Hex Prevents Socket Slippage
  • Accurate And Uniform Torque
  • Black Plated Finish
See More

Edelbrock – Performer 351-W Intake Manifold for S/B Ford 351 Windsor, Black Finish (Part No.21813)

Performer 351-W Intake Manifold for S/B Ford 351 Windsor, Black Finish

from

$597.99
Edelbrock part #21813 Performer 351W intake manifold is designed for street 351 c.i.d. Ford Windsor V8’s. Will not fit Boss 351. Aftermarket 4-bbl carbs are not compatible with Ford Auto Overdrive Transmission (AOD) unless used with Lokar bracket SRK-4000

Product Features:
  • Idle-5500 RPM Range
  • Dual Plane Type-4150 Style Flange
  • 3.4 in. Front Height, 4.07 in. Center Height, 4.75 in. Rear Height
  • Black Powder Coated Finish
  • Made In The USA
See More

Edelbrock – Sure Seat Valve Springs for Ford 289-302 (Part No.5822)

Sure Seat Valve Springs for Ford 289-302

from

$54.99
Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Competition Cams – Xtreme Energy 240/246 Hydraulic Flat Cam (Part No.35-250-4)

Xtreme Energy 240/246 Hydraulic Flat Cam

from

$284.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

Competition Cams – Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Ford 289-351W w/ 3/8" Stud (Part No.19043-16)

Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Ford 289-351W w/ 3/8" Stud

from

$427.99
These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Ford V8 289-302-351W applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:
  • CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
  • Designed for high performance street and race engines
  • Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
  • Additional clearance, up to 1.650″ O.D. valve spring
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9724)

Performer Series Retainer (Qty 16)

from

$100.99
Product Features:
  • Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
  • Set of 16
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

Edelbrock – Performer Small-Block Ford 5.0L/ 5.0L Cylinder Head 2.02" Bare (Part No.60389)

Performer Small-Block Ford 5.0L/ 5.0L Cylinder Head 2.02" Bare

from

$594.99


Product Features:
  • 50-State Street Legal Aluminum Cylinder Head
  • Out-of-the-Box Bolt-On Performance
  • Hand-Blended Intake and Exhaust Bowls
  • CNC-Matched Intake/Exhaust Ports in Std Location
  • Thicker Deck Surfaces than Other Brands
See More

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 11 Piece Set (Part No.1250)

Lower Intake Manifold Gasket Set: 11 Piece Set

from

$33.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
  • SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
  • ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
  • REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
  • EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
See More

Mr. Gasket – Intake Gasket (Part No.222)

Intake Gasket

from

$38.49
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.brbrFits all Ford 351M/400 – 4V or 4-Barrel heads.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Die-cut for an excellent fit
  • Can be trimmed if necessary for modified port applications
  • Complete with manifold end seals
  • For OE replacement, high performance street, drag race and oval track use
See More

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2941)

Engine Crankshaft Seal Kit

from

$48.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PTFE offers the best in fluid and high-temperature compatibility and contact sealing surface can run on undersize shafts, seal minor imperfections and virtually eliminate shaft wear.
  • Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Rear Main Seal Gasket (Part No.1963)

Rear Main Seal Gasket

from

$42.49
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:
  • Repairs That Leaky Rear Main Sail
  • Silicone Rubber to Withstand Extreme Engine Oil Temperatures
  • Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
  • Injection Molded for Precise Fit
See More

Mr. Gasket – Cam Change Gaskets (Part No.4410)

Cam Change Gaskets

from

$63.09
If you want to update just your camshaft and aren’t doing a complete engine overhaul, this kit contains all the gaskets needed to change out your camshaft. That way you don’t have to buy a complete gasket kit just to change the cam, but still can replace all the gaskets you should in the process.

Product Features:
  • Contains all the gaskets needed to change out your camshaft
  • Fuel Injector O-Ring Not Included
  • Meets Performance Standards
See More

Edelbrock – 289-302 Ford Head Bolt Kit (Part No.8552)

289-302 Ford Head Bolt Kit

from

$107.99


Product Features:
  • Highest Quality Head Bolts
  • Cold-Formed/Heat Treated
  • Ensures Molecular Integrity
  • Reduced Diameter Bolt Heads
  • Hardened/Parallel-Ground Washers Included
  • Rated At 170000 psi
  • Manufactured By ARP
See More

Edelbrock – Valve Cover Gasket Set for Ford (Part No.7569)

Valve Cover Gasket Set for Ford

from

$34.99
Product Features:
  • Valve Cover Gasket
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1684)

Engine Valve Cover Gasket Set

from

$46.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Rigid core, molded silicone rubber gaskets provide for ease of installation, and are great for on-again/off-again situations (like setting valve lash).
  • Features high-tech silicone material for long life, a solid steel core for strength and durability, and stainless steel compression limiters to prevent
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – TIMING CHAIN (Part No.7844)

TIMING CHAIN

from

$29.99
Product Features:
  • Timing Chain Only
See More

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7820)

Performer-Link Adjustable True-Roller Timing Chain Set

from

$67.99


Product Features:
  • Solid Bushing Chain Resists Stretching
  • For Use with Stock or Edelbrock Camshafts
  • Stressproof Steel Crank Gears
  • 3 Keyway Setting Points To Ensure Accurate Timing
  • True Bearing Surface Rolls with the Sprockets
  • For Engine with One-Piece Fuel Pump Eccentric
See More

Edelbrock – Water Pump for Small-Block Ford in Polished Finish (Part No.8846)

Water Pump for Small-Block Ford in Polished Finish

from

$381.99
Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in

Product Features:
  • Maximum Cooling for Street and Racing Engines
  • Internal Passages Are Balanced for Maximum Flow
  • Impeller is Larger than Others For Max Pressure
  • Impeller Vanes Dramatically Increase Flow Rates
  • Equal Distribution to Both Sides of Block
  • Only Flows in One-Direction for Optimum Efficiency
See More

Edelbrock – Water Pump Ford 5.0 V8 Reverse Rotation in Satin Finish (Part No.8840)

Water Pump Ford 5.0 V8 Reverse Rotation in Satin Finish

from

$305.99
Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in

Product Features:
  • Maximum Cooling for Street and Racing Engines
  • Internal Passages Are Balanced for Maximum Flow
  • Impeller is Larger than Others For Max Pressure
  • Impeller Vanes Dramatically Increase Flow Rates
  • Equal Distribution to Both Sides of Block
  • Only Flows in One-Direction for Optimum Efficiency
See More

Mr. Gasket – Mls Head Gasket (Part No.3175G)

Mls Head Gasket

from

$110.99
Our unique Multi-Layered steel head gasket embossment formation process optimizes the embossment radius, reduces stress points, enhances gasket conformability, and provides uniform clamp load distribution. This all results in superior surface contact between block and cylinder head. All head gasket layers/spacers go through an additional process to significantly reduce forming induced stress. Advantages are reduced brittleness in material, increased flexibility and deformation retention. This stabilizes the gasket, resulting in reduced cylinder bore distortion and improved combustion seal fro the extreme cylinder pressures found in high compression, supercharged and turbocharged applications. A proprietary polymer coating ensures the micro-seal of engine coolant and oil fluids.brbrA typical MLS head gasket requires a smoother (30Ra) surface finish than composite head gaskets. Mr. Gasket’s proprietary polymer coating will seal a surface finish twice as rough (60Ra) as a typical MLS head gasket. For high performance street, drag race and oval track use.

Product Features:
  • Gasket bore – 4.030 inch: Compressed thickness – .040 inch
  • Manufactured from 3-layer premium grade stainless steel and state of the art laser cutting
  • Optimized sealing embossments seals extreme cylinder pressure
  • Provides excellent stability and reduces cylinder bore distortion.
  • Proprietary polymer coating ensures the micro seal of engine coolant and oil fluids.
  • Ideal for supercharged, turbocharged, nitrous oxide and extreme compression ratio engines
  • For high-performance street, drag race and oval track use
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1013)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$58.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

Edelbrock – Cylinder Head Gasket Set for Ford (Part No.7328)

Cylinder Head Gasket Set for Ford

from

$62.99
Product Features:
  • Cylinder Head Gasket
  • 1970-1974 351c / 1975 1985 351m / 1971-1981 400m
See More

Edelbrock – Pushrod Set for Small Block Ford 289-302 (Part No.9632)

Pushrod Set for Small Block Ford 289-302

from

$210.99
Product Features:
  • Case-Hardened Tubing
  • Surface Hardening
  • Welded Ends
  • 0.3125 in. Diameter
  • Use with or without Hardened Steel Guideplates
See More

Edelbrock – Pushrod Set for Ford 289-302 (Part No.9655)

Pushrod Set for Ford 289-302

from

$208.99
Edelbrock part #9655 Pushrods are designed for small-block Ford 289-302 V-8 engine applications. These one-piece pushrods are manufactured from high quality 4130 Chromoly steel tubing that has been surface hardened for maximum durability. They have precis

Product Features:
  • 6.4 in. Length
  • 0.312 in. Diameter
  • 4130 Chromoly Steel Material
  • Black Oxide Finish
  • Made In The USA
See More

Edelbrock – Pushrod Set for Ford 351M/400 (Part No.9633)

Pushrod Set for Ford 351M/400

from

$188.99
Product Features:
  • 9.5 in. Length
  • 0.312 in. Diameter
  • 4130 Chromoly Steel Material
  • Black Oxide Finish
  • Made In The USA
See More

1968 Ford Bronco Performance Engines

Maybe you’re in the middle of a full rebuild of that 1968 Ford Bronco. Maybe you just need a couple of Performance Engines. Either way, Advance Auto Parts has 41 different Performance Engines in our inventory ranging from $19.99 to $1,035.99. That means you can find the exact parts or products you need to keep that 1968 Ford Bronco running smoothly.

Performance Engines are only as good as their brand. We stock 4 different brands to make sure you have plenty of trusted parts to choose from for your 1968 Ford Bronco. Mr. Gasket, FEL-PRO Performance, and Edelbrock are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Performance Engines for your 1968 Ford Bronco, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 350 reviews in this category, some of the top rated parts include ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST with 1.0 stars and Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 with 1.0 stars.

So if you’re in the market for aftermarket Performance Engines to keep your 1968 Ford Bronco rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Performance Engines Brands To Make Your 1968 Ford Bronco Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1968 Ford Bronco demands trusted brand parts and products to keep it running. Many trusted brands of Performance Engines make up Advance Auto Parts’ inventory, and all are ready to help make your Bronco the best it can be. Be sure to browse some of our top Performance Engines brands and parts.

Popular FEL-PRO Performance Performance Engines

We carry FEL-PRO Performance parts in our stock across Performance Engine Intake Manifold Gaskets and Performance Engine Valve Cover Gasket Sets categories, plus more. For a 1968 Ford Bronco, our most popular FEL-PRO Performance Performance Engines include:
Lower Intake Manifold Gasket Set: 11 Piece Set
from $33.99
(4)
Lower Intake Manifold Gasket Set: 11 Piece Set
Performance Engine Intake Manifold Gaskets
Engine Valve Cover Gasket Set
from $46.99
(1)
Engine Valve Cover Gasket Set
Performance Engine Valve Cover Gasket Sets
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
from $51.99
(2)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
Performance Engine Cylinder Head Gaskets

FAQs for 1968 Ford Bronco Performance Engines

What are the most purchased Performance Engines for the 1968 Ford Bronco?

Out of 41 Performance Engines for the 1968 Ford Bronco, the most popular in our inventory are:
Intake Manifold Gasket for 1963-1996 Small-Block Fords
from $28.99
(1)
Intake Manifold Gasket for 1963-1996 Small-Block Fords
Performance Engine Intake Manifold Gaskets
Performer-Link Adjustable True-Roller Timing Chain Set
from $67.99
This product is not rated
Performer-Link Adjustable True-Roller Timing Chain Set
Performance Engine Timing Sets and Components
289-302 Ford Head Bolt Kit
from $107.99
(7)
289-302 Ford Head Bolt Kit
Performance Engine Cylinder Head Bolts

What are the top-rated 1968 Ford Bronco Performance Engines?

Top-rated Performance Engines for your 1968 Ford Bronco based on customer reviews/ratings are:
ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST
from $237.99
(1)
ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST
“These things break very easy. Not a big fan of the soft brass when trying to install them with the screwdriver head they use. Change it hex and it woy”
Sure Seat Valve Springs for Ford 429/460 V8 1969-1987
from $111.99
(1)
Sure Seat Valve Springs for Ford 429/460 V8 1969-1987
“THIS WAS NOT A COMPLETE KIT!ONLY GOT VALVE SPRINGS!!!”