from

$11.99

Pinion gear thrust washer (0.875″ shaft) for 8.8″ Ford.

Product Features:

Pinion gear thrust washer for Ford 8.8″
0.875″ diameter cross pin shaft applications only

from

$11.29

Product Features:

O-ring for seal housing
Fits Dana Spicer 44 and Toyota 8″ and V6

from

$273.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Ford 9″ with LM603011 carrier races and Daytona pinion support
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, pilot bearing, thread locker, marking compound with brush and gasket.

from

$26.99

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
Left hand thread

from

$18.99

Product Features:

Bulkhead quit connect fitting

from

$11.99

9″ Ford gasket.

Product Features:

Dropout gasket
Fits Ford 9″

from

$9.99

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
1/2″ head

from

$36.99

Product Features:

Belleville plate, splined
Fits Dana Spicer 44 Powr Lok

from

$203.99

Product Features:

Fits Ford 9″ with 28 spline pinion
Larger inner pinion bearing reduces gear deflection under high load
Races installed
Nodular iron

from

$14.99

O-ring for 9″ Ford.Yukon Mighty seal.

Product Features:

Pinion support o-ring
Fits Ford 9″

from

$8.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits HM89410 race
All steel construction

from

$304.99

Yukon 1541H alloy left hand rear axle for Ford 9″ (’66-’75 Bronco) with length of 27-1/8″ and 28 splines. for use with 10″ x 2.25″ brakes. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects.

Product Features:

28 spline
5 lug
27 1/8″ long
Fits Ford 9″ in 1966-1975 Bronco
Left hand side
10″ x 2.5″ brakes

from

$207.99

Standard open or TracLoc cross pin shafts and block in four pinion design for 9″ Ford.

Product Features:

Cross pin shaft and block kit
Fits Ford 9″
Includes cross pin block and three cross pin shafts

from

$4.99

Trac Loc clutch guide for 9″ Ford.

Product Features:

Clutch guide
Fits Ford 8″ and 9″

from

$31.99

Product Features:

MINI SPOOL 8″ & 9″ 31 SPLN STL 090431

from

$947.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker uses 8620 internals and a patented design to provide maximum strength and reduce common failures. Assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

Fits Ford 9″ with 28 spline axles
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA

from

$8.49

High-quality Differential Carrier Shim Kit

Product Features:

CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

from

$175.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 9″ without aftermarket Daytona pinion support
Included are pinion bearings and races, pinion seal, pilot bearing , crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$359.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits Ford 9″
9.00″ ring gear diameter
28 spline pinion
10 ring gear bolts
3.25 ratio

from

$299.99

Product Features:

Spider gear kit
Fits Ford 8.8″ 31 spline Trac Loc positraction
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$789.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.

Product Features:

Fits Ford 9″ with 28 spline axles
Trac Loc positraction
Clutch style positraction
Street design
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$12.99

Product Features:

Cover gasket
Fits Dana Spicer 30

from

$6.99

Product Features:

Oil baffle for Dana Spicer 44

from

$13.59

Product Features:

FORD 9″ CROSS PIN

from

$172.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit