Name: Torker-Plus Camshaft Kit for 1957-1986 Small-Block Chevy 283-400 V8
Brand: Edelbrock
SKU: 5002
Price: 411.99 USD

from

$411.99

Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.

Product Features:

Designed for 2500 to 6500 Performance
Designed for Hi-Perf Street; Drag or Marine Use
Matched to Edelbrock Torker II Intakes
Includes Hydraulic Lifters and Assembly Lube
Dyno Matched/Street Proven Performance
Take The Guesswork Out Of Camshaft Selection

from

$157.99

Magnum Pushrods from COMP Cams offer an affordable solution for your .080″ wall chromemoly pushrod needs. Designed to withstand the stresses of a high performance engine, Magnum Pushrods are head-treated for extended durability and have precision formed, reinforced ends. Magnum Pushrods are black-oxide finished with their part number and length laser etched onto the surface for easy identification.

Product Features:

3/8″ Diameter, 7.800″ Length
Magnum Pushrods for Small Block Chevy
One-piece .080″ wall chromemoly steel tubing
Heat-treated for extended durability and guide plate compatibility
Precision formed and reinforced pushrod end

from

$958.99

The Edelbrock #607519 Performer cylinder head is designed for 302, 327, 350 and 400 cid small-block Chevy engines up to 1986. This cylinder head includes your choice of 64cc (In order to retain stock compression ratio on 1970 and earlier small-blocks) or

Product Features:

Complete Single For Hydraulic Flat Tappet
70cc Combustion Chamber Volume
185cc Intake/65cc Exhaust Runner Volume
2.02 in. Intake/1.6 in. Exhaust Valve Diameter
0.562 in. Deck Thickness

from

$73.99

These grade 8 alloy steel, longer length bolts are designed to compensate for thread length lost when using head bolt washers. This allows increased torque and clamping. Set of 16 does one cylinder head.

Product Features:

Cylinder Head Bolts
Longer-Than-Stock
High Quality Grade 8 Alloy
Increase Torque Settings
Higher Clamp Loads On Gasket

from

$27.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$412.99

These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Chevrolet V8 265-400 applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.

Product Features:

CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
Designed for high performance street and race engines
Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
Additional clearance, up to 1.650″ O.D. valve spring

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$27.49

These grade 5 hex head bolts are black coated plated for protection and appearance. Hardened flat washers provide uniform torque and prevent galling on aluminum manifolds.

Product Features:

Assures Accurate Torque App
Prevents Galling Manifold
Grade 5 Material
Black Oxide Coasted

from

$17.79

Big Block Chevrolet tubular head dowel, .638/.639 inch o.d. (outer diameter) by 1/2 inch. Packaged two per set. These hard to find dowel pins are precision machined then case hardened for accurate alignment in engine assembly.

Product Features:

Precision Machined
Case Hardened
Give Accurate Alignment
2 Per Set

from

$215.99

Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:

Twisted Snout Water Pump Design For Updated Style
Street Performance
Heavy Duty Shaft w/5/8 in. Pilot
Six-Blade Stamped Steel
Anti-Cavitation Impeller
100 Percent Leak Tested

from

$42.99

Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.brbrThese gaskets are .312 inch thick. That’s substantially thicker than stock which can allow for additional valve train clearance.brbrFits Chevrolet 396,402,427,454,502 Gen IV, Gen V and Gen VI Big Block.

Product Features:

This Gasket Has A Cork Rubber Blend
Provides Excellent Sealing And Durability
Extra Thick For The Hard To Seal Applications

from

$709.99

Holeshot 2400 for GM 1998 to 2002 4L60E Camaro and Firebird with an LS1 engine Application: GM 1998 to 2002 4L60E Camaro and Firebird with LS1 A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benef

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$542.99

HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.

Product Features:

HYDRAULIC – Thumpr: High performance street, stock converter ok, best with 2000+ converter and gears. Choppy/thumping idle.
279/296 Advertised Duration, 227/241 Duration @ .050″, .498″/.483″ Lift, 107 Lobe Separation
Valve spring upgrade required

from

$126.99

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 105 lbs. @ 1.700″, Open Pressure: 273 lbs. @ 1.250″
O.D.: 1.254″, I.D.: .880″
Single valve springs with damper
Approximately .490″ max lift at recommended installed height

from

$30.19

If you are changing your camshaft or replacing the timing set, make sure to replace this seal at the same time! Made from Nitrile rubber.

Product Features:

Nitrile Rubber And High Density Cork
Will Not Shrink Or Stick

from

$306.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$17.49

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

Zinc plated to resist corrosion and provide a clean professional appearance
Made from Grade 5 steel for strength and durability
Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
Allen (socket) Head
Zinc Plated For Protection

from

$39.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$99.99

Product Features:

Use W/ Valve Springs Part #5703, 5794
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$95.99

Valve spring retainers for use OE cast iron heads. Superior quality heat-treated steel. Machined for strength with black oxide finish. Finish ensures rust and corrosion protection.

Product Features:

Valve Spring Retainers for Use OE Cast Iron Heads
Superior Quality Heat-Treated Steel
Machined for Strength with Black Oxide Finish
Finish Ensures Rust and Corrosion Protection

from

$74.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$29.99

Product Features:

Timing Chain Only

from

$23.79

Spectre’s Chevrolet late model water neck offers the normal angled water neck and a 1/2 inch NPT threaded hole for a by-pass hose. This water neck has a chrome plated finish for a lasting look great and includes the bolts.

Product Features:

Fits Chevy engines
Includes a 1/2 inch NPT threaded hole for by-pass hose
Includes bolts
Chrome plated
Easy to install
O-ring/gasket not included

from

$26.99

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

Precision die-cast
Chrome plated for looks
O-ring seal to prevent water leaks
Mounting hardware included

from

$36.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.
Not intended for use in emission controlled vehicles.

from

$37.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$32.99

Product Features:

Clean Positive Seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads

from

$42.49

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Die-cut for an excellent fit
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use

1968 Chevrolet Corvette Performance Engines

More 1968 Chevrolet Corvette Performance Engines

Essential 1968 Chevrolet Corvette Performance Engines

Edelbrock – Torker-Plus Camshaft Kit for 1957-1986 Small-Block Chevy 283-400 V8 (Part No.5002)

Competition Cams – Magnum 7.800" Long, .080" Wall, 3/8" Diameter Pushrod Set (Part No.7513-16)

Edelbrock – RPM Small-Block Chevy Cylinder Head SBC 70cc Flat Tappet Cam Polished (Part No.607519)

Mr. Gasket – Ultra Seal: Cylinder Head Bolts (Part No.941G)

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1818)

Competition Cams – Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Chevrolet Small Block w/ 3/8" Stud (Part No.19002-16)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Mr. Gasket – Super Intake Manifold Bolts (Part No.6080)

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4377)

Weiand – Action Plus Water Pumps (Part No.9208P)

Mr. Gasket – Valve Cover Gasket Set (Part No.182)

B & M – Holeshot 2400 (Part No.70441)

Competition Cams – Thumpr 227/241 Hydraulic Flat Cam (Part No.11-600-4)

Competition Cams – Set of 16 Single Springs w/ 1.254" O.D., 1.254" I.D., 1.700" Installed Height (Part No.981-16)

Mr. Gasket – Timing Cover Seal (Part No.17)

Edelbrock – Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet (Part No.3702)

Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1010)

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9730)

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9721)

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7810)

Edelbrock – TIMING CHAIN (Part No.7844)

Spectre – Water Neck; Chevy Late Model (Part No.4730)

Mr. Gasket – Water Neck (Part No.2660)

FEL-PRO Performance – PERFORMANCE REAR MAIN SEAL SET (Part No.2912)

FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2919)

Edelbrock – Intake Manifold Gasket for 1965-1990, Oval port 396-402-454 B/B Chevy (Part No.7203)

Mr. Gasket – Intake Gasket (Part No.143)

Popular 1968 Chevrolet Corvette Performance Engines Categories

1968 Chevrolet Corvette Performance Engines

Performance Engines Brands To Make Your 1968 Chevrolet Corvette Last

Popular B & M Performance Engines

Top 1968 Chevrolet Corvette Performance Engines from Mr. Gasket

FAQs for 1968 Chevrolet Corvette Performance Engines

What are the most purchased Performance Engines for the 1968 Chevrolet Corvette?

What are the top-rated 1968 Chevrolet Corvette Performance Engines?

More Popular Parts for All Makes