1968 Chevrolet C10 Suburban Drivetrains
More 1968 Chevrolet C10 Suburban Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1968 Chevrolet C10 Suburban, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1968 Chevrolet C10 Suburban Drivetrains
Motive Gear – Drive Shaft Pinion Yoke (Part No.MG1310-6010)
Motive Gear – Differential Bearing Kit – Koyo (Part No.R12R)
from
$102.99
Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv
Product Features:
See More
Product Features:
- KIT BRG & SL 12 BLT 8 7/8
Motive Gear – Differential Crush Sleeve (Part No.3954482)
Yukon Gear – Redi-Sleeve Yoke Saver For 8.75" C, 9.25" C, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD (Part No.30228)
from
$37.99
Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.
Product Features:
See More
Product Features:
- Redi-Sleeve yoke saver
- Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD
Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)
from
$34.49
Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHEV 60-02; DODGE 57-02; FORD 55-07; GMC 63-02; INTL 57-02; KW 81-18; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.
Product Features:
See More
Product Features:
- MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
- HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
- READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
- For Years: 1955-2018
- Weight approx: 4 Lbs
- BEARING ID / BORE: 1.5750 INCH / 40 MM
- CENTERLINE: 2.48 INCH / 63 MM
- MOUNT WIDTH: 6.62 INCH / 168 MM
- STYLE: ROUND FRAME
- NOT PICTURED: TWO DUST SHIELDS
Yukon Gear – Pinion Install Kit For Dana 60 Rear Differential (Part No.13032)
from
$295.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60 rear
- Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.
National – Bearings (Part No.HM88610)
from
$15.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Driveworks – Universal Joint (Part No.DW-331)
from
$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
National – Multi Purpose Bearing (Part No.HB-88107-A)
from
$44.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Controlled heat treating process for lasting performance and extended bearing life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – The Carrier Bearing Puller (Part No.56072)
from
$883.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.
Product Features:
See More
Product Features:
- Carrier bearing puller
- Works with an impact gun to safely and easliy remove carrrier bearings
National – Shaft Repair Sleeve (Part No.99125)
from
$27.49
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
- Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1410 U/Joint Size (Part No.41030)
from
$278.99
Yukon replacement yoke for Dana 60 and 70 with a 1410 U/joint size. 4.188″ snap ring span, 1.188″ cap diameter. Outside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60, 70, 70U and 70HD
- 29 spline
- 1410 u-joint size
- 4.188″ snap ring span
- 1.188″ cap diameter
- Outside snap ring design
- Strap style
Yukon Gear – Replacement Inner Axle Seal For Dana 44 (Flanged Axle) (Part No.30303)
from
$7.99
Replacement inner axle seal for Dana 44 (flanged axle) .Yukon Mighty seal.
Product Features:
See More
Product Features:
- Inner axle seal
- Fits Dana Spicer 44 rear with flanged axle
Richmond Gear – RngPnnInstlKt (Part No.83-1034-B)
from
$59.99
RngPnnInstlKt
Yukon Gear – Spindle Nut Retainer For Dana 60 & 70, 1.830" I.D., 10 Outer TABS (Part No.33477)
from
$10.99
Spindle nut retainer for Dana 60 & 70, 1.830″ I.D., 10 outer tabs. This replaces Spicer part number 30637.
Product Features:
See More
Product Features:
- Spindle nut retainer for Dana Spicer 60, 70, 70U and 70HD
- 1.830″ I.D.
- 10 outer tabs
Yukon Gear – Bearing Race Driver (Part No.56011)
from
$215.99
Bearing race driver for Dana 60 front, Dana 70U rear, Chrysler 8.75″ with 42 housing, and ’88 and older GM 14T. No return.
Product Features:
See More
Product Features:
- Bearing race driver
- Fits HM803110 race
- All steel construction
Yukon Gear – Carrier Installation Kit For Dana 60 Differential (Part No.57005)
from
$194.99
Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Dana 60 differential. This kit contains carrier bearings, races and shims.
Product Features:
See More
Product Features:
- Fits Dana Spicer 60
- Includes carrier bearings and races and carrier shim kit
Yukon Gear – Replacement Standard Open Carrier Case For Dana 60, 4.56 & Up (Part No.20046)
from
$389.99
Yukon replacement standard open carrier case for Dana 60, 4.56 & up (incl ABS) 2-7/16″ tall.
Product Features:
See More
Product Features:
- Standard open carrier case
- Does not include spider gears
- Fits Dana Spicer 60
- 4.56 and up ratio only
- ABS and non-ABS compatible
Pro-King – Pinion Seal (Part No.740A070)
from
$2.39
Pro-King is the leading supplier of transmission and driveline products in the aftermarket.
Product Features:
See More
Product Features:
- All products are designed to meet or exceed OE quality, form, fit and funtion.
Yukon Gear – Dana 60 & Dana 61 Tracloc Clutch Set (Part No.16156)
from
$269.99
Dana 60 & Dana 61 TracLoc clutch set.
Product Features:
See More
Product Features:
- Clutch kit
- Fit Dana Spicer 60 Trac Loc positraction
Motive Gear – Axle Shaft (Part No.14071751)
from
$129.99
The Motive Gear replacement axle shaft offers an OE-quality axle shaft at a fraction of the OE cost. Manufactured from 1541H material on high-tolerance CNC equipment, this axle shaft is designed to provide a perfect fit every time.
Product Features:
See More
Product Features:
- AXLE SHAFT 8 7/8 2 WD 31 1/4 TRK 30 SPL 5 LUG
Yukon Gear – Dana 60, Dana 70 & Dana 80 Cover Bolt (Part No.33235)
from
$5.99
3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.
Product Features:
See More
Product Features:
- Cover bolt for Dana Spicer 60, 70 and 80
- 3/8″
National – Multi Purpose Seal (Part No.481181N)
from
$13.49
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Low swell in hydrocarbon fluids
- Design type: spring loaded; multi-lip
- Provides good low temperature capability
- Temperature range: -40°F to 225°F; -40°C to 107°C
- Delivers quality and reliable performance for every type of repair
Yukon Gear – Side Gear Thrust Washer For Dana 60, 70 & 80 (Part No.33532)
from
$4.99
Product Features:
See More
- Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
- Fits standard open differentials only
Motive Gear – Differential Pinion Shim Kit (Part No.1118)
Yukon Gear – Replacement Outer Oil Slinger For Dana 60, 70, 70U & 70HD (Part No.33019)
Mr. Gasket – Differential Cover Kit (Part No.9895)
from
$72.39
The Mr. Gasket chrome plated rear end cover is made from heavy-gauge steel, and comes complete with bolts and gaskets.
Product Features:
See More
Product Features:
- Chrome plated steel for looks
- Includes bolts and gasket
Yukon Gear – Spindle Nut For Dana 60, 1.750" I.D., 6 Sided (Part No.33476)
from
$15.99
Spindle nut for Dana 60, 1.750″ I.D., 6 sided. This replaces Spicer part number 30636.
Product Features:
See More
Product Features:
- Spindle nut
- Fits Dana Spicer 60
- 6 sides
- 1.750″ I.D.
Popular 1968 Chevrolet C10 Suburban Drivetrains Categories
1968 Chevrolet C10 Suburban Drivetrains
You count on your 1968 Chevrolet C10 Suburban to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 297 Drivetrains ranging in price from $3.99 to $1,487.99, you’re sure to find everything you need for your 1968 Chevrolet C10 Suburban.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 18 different brands like Moog, Valvoline, and Driveworks. 1968 Chevrolet C10 Suburban Drivetrains start as low as $3.99!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 8,508 extensive product reviews on 1968 Chevrolet C10 Suburban Drivetrains. Some of the top-rated Drivetrains products we carry are Universal Joint with 4.4 stars and Bearings with 4.2 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1968 Chevrolet C10 Suburban below to get started!
Top-Rated Drivetrains Brands For Your 1968 Chevrolet C10 Suburban
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1968 Chevrolet C10 Suburban running right for years to come. In our inventory you’ll find brands like Moog, Valvoline, Driveworks, and even more.
Popular Valvoline Drivetrains
You’ll find popular Valvoline brand products across Differentials. All are waiting to get your 1968 Chevrolet C10 Suburban back on the road. Some of the top-rated Valvoline products in these categories are:
from
$12.79
(446)
MaxLife Multi-Vehicle (ATF) Full Synthetic Automatic Transmission Fluid, 1 Quart
Differential Oil
FAQs for 1968 Chevrolet C10 Suburban Drivetrains
What are the most purchased Drivetrains for the 1968 Chevrolet C10 Suburban?
Out of 297 Drivetrains for the 1968 Chevrolet C10 Suburban, the most popular in our inventory are:
What are the top-rated 1968 Chevrolet C10 Suburban Drivetrains?
Top-rated Drivetrains for your 1968 Chevrolet C10 Suburban based on customer reviews/ratings are:
from
$16.99
(39)
Bearings
“Perfect fit. Make sure you get your bearings completely filled with grease when reassembling your hubs.”
from
$32.99
(37)
Greaseable Super Strength Universal Joint
“grease fitting I like location dont like needle design to grease should be regular design fitting”
