1968 AMC Javelin Air Intakes
More 1968 AMC Javelin Air Intakes Categories
If you’re looking for an original Air Intakes replacement for a 1968 AMC Javelin, you can search through our selection below. You’ll also find aftermarket and OEM Air Intakes to meet your needs.
Essential 1968 AMC Javelin Air Intakes
Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)
from
$24.99
The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.
Product Features:
See More
Product Features:
- Steel Material
- For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
- Includes Lightest To Heavy
- Set of 7
- Made in The USA
Edelbrock – Standard Flow Carburetor Power Valve #12655 Single Stage 5.5in Hg (Part No.12655)
from
$16.99
Product Features:
See More
- The Edelbrock #12645 Single Stage 5.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Mr. Gasket – Intake Manifold Bolt Set – Chevrolet Small Block – Socket Head 3/8"-16 X 1" Bolts & Washers (Part No.956G)
from
$17.49
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers
Product Features:
See More
Product Features:
- Zinc plated to resist corrosion and provide a clean professional appearance
- Made from Grade 5 steel for strength and durability
- Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
- Allen (socket) Head
- Zinc Plated For Protection
Mr. Gasket – Intake Manifold Bolts (Part No.955G)
from
$15.49
These grade 5 socket head bolts are zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8-16 x 1 inch bolts & washers.
Product Features:
See More
Product Features:
- Grade 5 socket head bolts are zinc plated for protection and appearance
- Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds
- Washers Included
Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1762)
from
$24.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
See More
Edelbrock – Carburetor Repair Kit #12760 Fits Most Holley 4150 Carburetors (Part No.12760)
from
$57.99
Product Features:
See More
- The Edelbrock #12760 4150 Carburetor rebuild kit is for Holley, Demon and Quick Fuel Carburetors.
- The kit comes with the necessary components to rebuild a 4150 style Carburetor.
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1007)
from
$12.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Carquest – Carburetor Choke Pull-Off (Part No.779-070)
from
$13.05
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.
Product Features:
See More
Product Features:
- Designed to OE standards for ease of installation
- Designed and manufactured to our stringent quality standards at a certified facility, so you can install with confidence
- Premium components and durable materials withstand harsh engine conditions to increase longevity and lifespan
- Undergoes extensive testing and validation for proper performance and peak reliability
- As a global manufacturer of automotive aftermarket products, we maintain complete quality control throughout the manufacturing process
Holley – REPLACEMENT MAIN BODY KIT FOR 0-80457S (Part No.134-342)
from
$195.99
REPLACEMENT MAIN BODY KIT FOR 0-80457S
Mr. Gasket – Ultra Seal: Intake Gasket (Part No.5844)
from
$48.49
Mr. Gasket Ultra-Seal Intake Manifold Gasketss are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Silicone beading on both sides of each gasket
- For OE replacement, high performance street, drag race and oval track use
- Silicone Bead Around Port
- Creates Tight Leak proof Seal
Sealed Power – Valley Pan Gasket Set (Part No.260-4008)
from
$19.49
Sealed Power« parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.
See More
Edelbrock – Standard Main Jet Carburetor Metering Jet #12457 Size .056 (Pair) (Part No.12457)
from
$13.99
The Edelbrock 94 #12457 Carburetor Jets .057″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 57 Maximum Jet Size
- 0.056 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$13.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – RPM Air-Gap AMC 290/343/390 Intake Manifold (Part No.7530)
from
$509.99
Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RMP street driven power. Dual-plane high-rise intake with 180 degree firing order. Produces incredible top-end horsepower. Retai
Product Features:
See More
Product Features:
- Based on Performer RPM-Series with Unique Air Gap
- Air Gap Cooler and Denser Mixture for More Power
- Designed for 1500 to 6500 RPM Street-Driven Power
- Dual-Plane High-Rise Intake w/180 deg Firing Order
- Produces Incredible Top-End Horsepower
- Retains Good Throttle Response and Acceleration
- Includes Std Oil Fill ; PCV ; A/C Accy Bosses
- Not for Exhaust-Heat Chokes – No Exhaust Crossover
Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)
from
$18.99
Product Features:
See More
- The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
- Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$20.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Performer 14073 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Inlet, Black (Part No.14073)
from
$527.99
Product Features:
See More
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Manual Choke, Black
- 4 Barrel Count
- Square Bore
United Carb – Remanufactured Carburetor 1 Barrel (Part No.10-1090)
from
$310.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$62.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$40.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Felpro – Carburetor Mounting Gasket (Part No.60091)
from
$4.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Carburetor Mounting Gasket (Part No.60059)
from
$2.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Carburetor Mounting Gasket (Part No.60012)
from
$5.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Carburetor Mounting Gasket (Part No.60044)
from
$3.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Carburetor Accelerator Pump Diaphragm #12401 50cc (Part No.12401)
from
$31.99
Edelbrock #12401 50cc Accelerator Pump Diaphragm for 4150 Carburetors. Proper installation is the responsibility of the installer. Improper installation will void your warranty and may result in poor performance and engine or vehicle damage.
Product Features:
See More
Product Features:
- Rubber Material
- For Holley®, Barry Grant, And Demon Gasoline Carburetors
- No Hardware Included
- 50cc Volume
- Made iIn The USA
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$12.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Popular 1968 AMC Javelin Air Intakes Categories
1968 AMC Javelin Air Intakes
You count on your 1968 AMC Javelin to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Air Intakes. With 41 Air Intakes ranging in price from $1.99 to $541.99, you’re sure to find everything you need for your 1968 AMC Javelin.
Brands matter. If you want to shop a specific Air Intakes brand, we stock 7 different brands like Mr. Gasket, Edelbrock, and Holley. 1968 AMC Javelin Air Intakes start as low as $1.99!
One of the best ways to find top quality OEM or aftermarket Air Intakes is by asking professionals. Short of that, you can shop with confidence thanks to our 774 extensive product reviews on 1968 AMC Javelin Air Intakes. Some of the top-rated Air Intakes products we carry are Standard Flow Carburetor Power Valve #12625 Single Stage 2.5in Hg with 4.5 stars and Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs with 4.5 stars.
Did we mention you can order your Air Intakes from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Air Intakes inventory for your 1968 AMC Javelin below to get started!
Top-Rated Air Intakes Brands For Your 1968 AMC Javelin
Trusted Air Intakes OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1968 AMC Javelin running right for years to come. In our inventory you’ll find brands like Mr. Gasket, Edelbrock, Holley, and even more.
Popular Holley Air Intakes
You’ll find popular Holley brand products across Carburetor Parts. All are waiting to get your 1968 AMC Javelin back on the road. Some of the top-rated Holley products in these categories are:
from
$456.99
(45)
Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny
Carburetors
FAQs for 1968 AMC Javelin Air Intakes
What are the most purchased Air Intakes for the 1968 AMC Javelin?
Out of 41 Air Intakes for the 1968 AMC Javelin, the most popular in our inventory are:
from
$43.99
This product is not rated
Carburetor Repair Kit #12750 Fits Most Holley 4160 Carburetors
Carburetor and Injector Seal Kits
What are the top-rated 1968 AMC Javelin Air Intakes?
Top-rated Air Intakes for your 1968 AMC Javelin based on customer reviews/ratings are:
from
$16.99
(27)
Standard Flow Carburetor Power Valve #12625 Single Stage 2.5in Hg
“Works perfectly”
from
$14.99
(4)
Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors
“Was the wrong slip joint. Catalog was very confusing to use and misleading. Had to locate through another website.”
