1967 Plymouth Belvedere Differentials

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Chrysler 8.75″ ’89’ case housing with LM104912 carrier races
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings

89 housing nodular Iron Drop Out case, up to 500 HP, Billet adjuster for 8.75″ Chrysler. This dropout does not come with fill plug (Part number CHY612017).

Product Features:

• Fits Chrysler 8.75″
• ’89’ case design
• Nodular iron for added strength

Cross pin shaft for 8.25″ Chrysler.

Product Features:

• Cross pin shaft for Chrysler 8.25″
• Fits standard open differentials only

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

• Redi-Sleeve yoke saver
• Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

Product Features:

• BILLET HP 1350-29 SPLINE YOKE

Yukon 1541H alloy cut to fit rear axle for Chrysler 8.75″ measuring 28″-32″ with 30 splines and 5×4.5 bolt pattern. for use with A, C & E-Body. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. Must use Green bearing.

Product Features:

• Fits Chrysler 8.75″
• 30 spline
• Cut to length design fits 28″-32″ applcations
• 5 x 4.5″ bolt pattern

Yukon yoke for Chrysler 8.75″ with 10 spline pinion and a 7290 U/joint size (1350 with U/joint adapter.) All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Chrysler 8.75″
• 10 spline
• 7290 u-joint size
• Inside snap ring design
• 2.625″ snap ring span
• 1.125″ cap diameter
• Strap style

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

• Fits Chrysler 8.75″ ’42’ case with 25520 carrier races
• Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, thread locker, marking compound with brush, and gasket.

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Product Features:

• CHRY 10BLT 8.75 EARLY R/P 3.55 MGP 29SP USE MG7260-C875/MG1350-C87529

Product Features:

• CHRY 8 3/4″ RING GEAR BOLTS C 8.25″

RngPnnInstlKt

Product Features:

• Rubber fill plug
• Fits Chrysler 7.25″, 8.25″ and 9.25″

Product Features:

• CRUSH SLEEVE 7.25 & 8.25 MIN ORDER 5000

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

Product Features:

• FULL SPOOL DANA 60 35 SPLINE 4.10 & DOWN

Side gear thrust washer for 7.25″ Chrysler.

Product Features:

• Side gear thrust washer kit
• Fits Chrysler 7.25″

Chrysler 8.75″ (coarse spline) pinion nut washer.

Product Features:

• Pinion nut washer
• Fits Chrysler 8.75″ with 10 spline pinion

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

8.25″ Chrysler, Model 35, D36 ICA, & Dana 28 TracLoc clutch set.

Product Features:

• Clutch kit
• Fits Chrysler 8.25″ Trac Loc positraction

High-quality Differential Component Shim

Product Features:

• SHIM KIT FITS-8.25-F7.5-AMC20-GM0

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

• Includes four quarts of Redline Shockproof oil

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Design type: spring loaded; multi-lip
• Temperature range: -50 Deg. F to 200 Deg. F / -46 Deg. C to 93 Deg. C
• Good dry running capabilities
• Compatible with all oils and greases
• Delivers quality and reliable performance for every type of repair

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M802011 race
• All steel construction