1967 Mercury S-55 Performance and Racing Products

Essential Performance and Racing Products for 1967 Mercury S-55s

Accel – Supercoil (Part No.140001)

Supercoil

from

$105.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:
  • Oil Filled For Better Cooling
  • Optimized Low Resistance
  • Silicon Magnetic Steel E-Core
  • Higher Energy/Voltage Outputs
  • Quicker Starts
  • Improved Idle Quality
  • Resists Shock And Vibration
  • Resists Corrosion
See More

Edelbrock – Performer RPM 2 Carb/Plate Nitrous Systems Square-Bore Carbs (100-400+ Hp) (Part No.70082)

Performer RPM 2 Carb/Plate Nitrous Systems Square-Bore Carbs (100-400+ Hp)

from

$1114.99


Product Features:
  • Designed For Carbureted V8 Engines
  • Enhanced Flow Capacity
  • Add Power In Stages
  • Softens The Hit Of The Nitrous System
See More

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1442)

Exhaust Manifold Gasket Set

from

$33.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Energy Suspension – Control Arm Bushing Set (Part No.4.3102R)

Control Arm Bushing Set

from

$17.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:
  • Maintains Better Alignment While Driving
  • Full Floating and Non Binding
  • Fits Into the Remaining Stock Control Arms
See More

Mallory – Unilite Ignition Module (Part No.605)

Unilite Ignition Module

from

$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:
  • Service Part
  • No Moving Parts To Wear Out
  • Self Contained Unit
  • Can Drive OEM
  • Can Drive High Performance Ignition Coils
See More

Energy Suspension – Control Arm Bushing Set (Part No.4.3102G)

Control Arm Bushing Set

from

$16.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:
  • Maintains Better Alignment While Driving
  • Full Floating and Non Binding
  • Fits Into the Remaining Stock Control Arms
See More

MSD Ignition – Distributor; Ford FE; Ready-to-Run (Part No.8595)

Distributor; Ford FE; Ready-to-Run

from

$569.99
MSD is excited to offer two Ready-to-Run distributors for two classic Ford engines! These distributors are the answer to weak breaker points or rebuilt aftermarket models. Inside the billet housing there is a high-output ignition module. When the maintenance-free magnetic pick-up signals the module to fire, up to 7.5 A is sent to the coil where a powerful spark is created. This improved spark output results in quick starts, snappy throttle response and terrific drivability. The distributors are equipped with a vacuum advance canister for cruising economy. Plus, there is a mechanical advance assembly that is mounted on top of the distributor shaft making it easy to adjust the advance to meet your needs. Another great feature of the Ready-to-Run distributors is their simple installation! All you need to do is connect three wires and you’ll be cruising!

Product Features:
  • Simple and clean three wire installation
  • CARB E.O. Approved
  • Does not require an MSD Ignition Control
  • Supplied w/small dia. cap w/HEI style terminals; race and rotor
  • Will accept PN[8441] Cap-A-Dapt
  • Nylon pads ensure smooth operation of the advance weights
  • Advance weight pins are staked and tig welded to the plate
  • Mech. advance assem. can be locked out for crank trigger systems
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1817)

PERFORMANCE OIL PAN GASKET SET

from

$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

FAG US – CUP (Part No.LM48510)

CUP

from

$7.69
CUP

Edelbrock – Valve Cover Gasket Set for Ford (Part No.7568)

Valve Cover Gasket Set for Ford

from

$40.99
Product Features:
  • Valve Cover Gasket
See More

Mr. Gasket – Intake Gasket (Part No.202A)

Intake Gasket

from

$40.19
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. Complete with manifold end seals and distributor gasket (where applicable). For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Can be trimmed if necessary for modified port applications
  • Complete with manifold end seals and distributor gasket where applicable
  • For OE replacement, high performance street, drag race and oval track use
See More

Mr. Gasket – Chrome Distributor Hold-Down Clamp (Part No.9860)

Chrome Distributor Hold-Down Clamp

from

$13.29
Chrome plated steel. Includes hold-down bolt or stud. Holds the distributor in place for accurate timing. Serrated bottom prevents the distributor from turning.

Product Features:
  • Rolled Edges For Strength
  • Ideal For Magnetos
  • Ideal For Ignition Distributor
See More

Edelbrock – Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79 (Part No.5792)

Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79

from

$141.99
Product Features:
  • Non-Rotator Type
  • 1.550 in. Outer Diameter
  • .190 Wire Size
  • Single Coil Spring Type
  • Set of 16
See More

Edelbrock – Performer RPM Carb/Plate Nitrous Systems 4500 Series Carbs (100-150-250 Hp) (Part No.70053)

Performer RPM Carb/Plate Nitrous Systems 4500 Series Carbs (100-150-250 Hp)

from

$757.99


Product Features:
  • Designed For Carbureted V8 Engines
  • Simple To Install
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Accel – Contact And Condenser Kit (Part No.8203)

Contact And Condenser Kit

from

$79.99
Regain horsepower and economy for your street machine with new contact and condenser kit. Large tungsten contacts provide crisp coil firing and perform solidly up to 5,000 RPM. Condenser’s special winding protects from pitting of point contacts. Heavy duty 23 ounce points.

Product Features:
  • High Performance Points and Condenser
  • With Integral Conductor
See More

Edelbrock – Performer 1412 Carburetor: 800 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1412)

Performer 1412 Carburetor: 800 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$538.99
The Edelbrock 1412 Performer Series 800 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1412 Performer Series 800 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation. Dyno tests proved that the EPS 800 carb outperformed a Holley #3310 carb out-of-the-box by 26 ft-lbs. of torque and 22 hp on a small-block Chevy engine equipped with an Edelbrock Performer RPM power package

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
  • Can Easily Calibrate with Rods and Jets
See More

Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)

Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$394.99
The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1020)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$41.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Cylinder Head Gasket Set for Ford (Part No.7337)

Cylinder Head Gasket Set for Ford

from

$61.99
Product Features:
  • Cylinder Head Gasket Set
  • 1958-1976 390-428
See More

Edelbrock – Performer 390 Intake Manifold for Ford FE, Satin Finish (Part No.2105)

Performer 390 Intake Manifold for Ford FE, Satin Finish

from

$597.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 deg. Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • 50-State Street Legal if Correct Carburetor Used
See More

Edelbrock – #21053 Performer 390 Intake Manifold, Ford FE, 332-428, Black Finish (Part No.21053)

#21053 Performer 390 Intake Manifold, Ford FE, 332-428, Black Finish

from

$479.99
The Edelbrock Performer 390 #21053 intake manifold is designed for street 332-352-360-390-406-410-427-428 c.i.d. Ford V8’s with medium- or low-rise cylinder heads. Manifold not equipped with EGR; will not accept stock Motorcraft spread-bore carburetor or
See More

Motive Gear – Differential Carrier (Part No.D3TZ4204A)

Differential Carrier

from

$226.99


Product Features:
  • FORD 9″ EMPTY POSI CASE – 28 & 31 SPLINES
See More

B & M – Transpak, 67-91 C6 Transmission (Part No.40228)

Transpak, 67-91 C6 Transmission

from

$152.99
Use the B&M Transpak to recalibrate your automatic transmission for optimum performance. With the Transpak you will be able to downshift into low at any speed, and keep it in low to any speed that you want.

Product Features:
  • Recalibrate Auto. Transmission
  • Optimum Performance
  • Select Your App. Mode
  • Improves Transmission Life
  • Trans. Removal Not Required
See More

B & M – Automatic Shifter, Quicksilver 4 Speed (Part No.80683)

Automatic Shifter, Quicksilver 4 Speed

from

$439.99
The B&M Quicksilver features a ratcheting action for positive shifts, Chrome Knob, neutral safety switch, NHRA/IHRA approved Reverse Lockout. Fits Most 3 and 4 speeds.

Product Features:
  • Universal Floor Mount Application
  • Base Trimmed For Custom Fit
  • Cable Operated
  • Quick Installation
  • Accurate Shifting
See More

Hurst – Manual Shifter, Competition Plus (Part No.3913180)

Manual Shifter, Competition Plus

from

$533.99
The industry standard for over 30 years, this shifter offers state of the art transmission control for popular manual transmissions. Dedicated applications assure a custom fit to a wide variety of vehicles.

Product Features:
  • High Ratio Pivot Mechanism
  • Adjustable Bias Spring Loads
  • Adjustable Stops
  • Chrome Plated Steel Bolt On Stick
  • Easy Installation
See More

B & M – Automatic Shifter, Light Truck Megashifter (Part No.80680)

Automatic Shifter, Light Truck Megashifter

from

$479.99
The B&M Megashifter has it all, form, function and classic style. This all adds up to bring you a quality shifter that’s been one of the most popular automatic shifters of all time. The light truck Megashifter is better suited for truck and bench seat applications with its overall height of 14.85-inches tall (2.25-inches taller than #80690 Megashifter.) The positive ratcheting action won’t allow you to over-shift and miss a gear at that critical moment, along with the reverse lockout feature meets NHRA/IHRA safety rules for those weekend grudge races at the track, while the look and feel of the T-handle and accordion style shift boot really shows off its racing heritage. Other features include a black console that you can trim to match the contour of your vehicle’s floor, 5-foot long shifter cable, cable brackets, transmission shift levers, chrome plated top plate with lighted gear indicator and everything needed for an easy at home installation. An optional T-handle with a 12-volt button is available separately for actuating a trans-brake, nitrous oxide or other accessories for the hard-core performance enthusiast. This shifter fits most popular Chrysler, Ford and GM 3 and 4-speed automatic transmissions. Note: AOD transmissions require optional kit #40496, GM 4L60E through 4L85E transmissions with PRNDL switch will require optional kit #70499. Overall Dimensions – 14.9L x 6.4W x 14.8H

Product Features:
  • Universal Floor Mount Application
  • Cable Operated
  • Quick Installation
  • Accurate Shifting
  • NHRA/IHRA Reverse Lockout Meets Requirements
  • Use w/Reverse Pattern Valve Body
  • Includes Neutral Safety Switch
  • Includes Backup Light Switch
See More

Hurst – Manual Shifter, Indy, SSA 3 Speed Shifter (Part No.5010002)

Manual Shifter, Indy, SSA 3 Speed Shifter

from

$369.99
Hurst Indy SSA 3-speed shifter kits are designed to be used on most popular 3-speed transmissions in a wide variety of cars. Applications are determined by transmissions and an exclusive engineered mounting design, for most applications.

Product Features:
  • Spring Loaded Gate
  • Short Precise Throws
  • Chrome Plated Stick
  • All Components Are Plated
  • Complete with Shifter Boot and Hardware
See More

Upgrade your 1967 Mercury S-55 with Top-Quality Performance and Racing Products

When it comes to maintaining or upgrading your 1967 Mercury S-55, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Mercury or enhancing its overall performance, Performance and Racing Products are key to keeping your S-55 functioning at its best. At Advance Auto Parts, we offer a wide selection of 36 Performance and Racing Products for the 1967 Mercury S-55, designed to meet your needs without breaking the bank. From Performance Engine replacements to Performance Fuel Systems upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1967 Mercury S-55 at great prices. Our Performance and Racing Products inventory for this model ranges from just $7.69 to $1,114.99, with an average price of $324.43. Our 36 Performance and Racing Products in stock come from 11 trusted brands, so you’re sure to find the right part for your 1967 Mercury S-55 without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1967 Mercury S-55, we stock popular OEM and aftermarket Performance and Racing Products from top names like Edelbrock, Mr. Gasket, FEL-PRO Performance, and more. Edelbrock Performance and Racing Products start at just $40.99 and boast an impressive 4 stars average rating from customers. Mr. Gasket and FEL-PRO Performance also bring quality to the table, with Performance and Racing Products available starting at $13.29, and at an average 4 stars rating. With 165 customer reviews and counting, our 1967 Mercury S-55 Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Fluids and Chemicals and more to make sure your 1967 Mercury S-55 is always ready to roll. We’re committed to providing you with everything you need to keep your S-55 in top shape, all in one place. Start shopping confidently below for your 1967 Mercury S-55!

Best-Selling Performance Engines for 1967 Mercury S-55s

Enhance the driving experience in your Mercury with 10 quality Performance Engine components, starting at $26.99.

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Edelbrock – Performer 390 Intake Manifold for Ford FE, Satin Finish (Part No.2105)

Performer 390 Intake Manifold for Ford FE, Satin Finish

from

$597.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 deg. Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • 50-State Street Legal if Correct Carburetor Used
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1020)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$41.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1817)

PERFORMANCE OIL PAN GASKET SET

from

$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 5 Piece Set (Part No.1246)

Lower Intake Manifold Gasket Set: 5 Piece Set

from

$39.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro performance intake manifold gaskets have been tested with virtually all aftermarket cylinder head and intake manifold combinations.
  • Performance intake manifold gaskets designed without a metal core, to allow engine builders to trim the gasket for exact fit on modified ports.
  • Standard and Low riser
  • Printoseal elastomeric sealing beads to provide extra sealing strength around the intake port.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79 (Part No.5792)

Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79

from

$141.99
Product Features:
  • Non-Rotator Type
  • 1.550 in. Outer Diameter
  • .190 Wire Size
  • Single Coil Spring Type
  • Set of 16
See More

Edelbrock – Cylinder Head Gasket Set for Ford (Part No.7337)

Cylinder Head Gasket Set for Ford

from

$61.99
Product Features:
  • Cylinder Head Gasket Set
  • 1958-1976 390-428
See More

Edelbrock – Valve Cover Gasket Set for Ford (Part No.7568)

Valve Cover Gasket Set for Ford

from

$40.99
Product Features:
  • Valve Cover Gasket
See More

Mr. Gasket – Intake Gasket (Part No.202A)

Intake Gasket

from

$40.19
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. Complete with manifold end seals and distributor gasket (where applicable). For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Can be trimmed if necessary for modified port applications
  • Complete with manifold end seals and distributor gasket where applicable
  • For OE replacement, high performance street, drag race and oval track use
See More

Mr. Gasket – Head Gasket (Part No.1132G)

Head Gasket

from

$37.59
Mr. Gasket Embossed Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. This is a very unique design that has a solid metal on metal fold at the combustion seal. This fold makes for a very stout seal that is almost the equivalent of a higher-end MLS (multi-layer steel) gasket with a gas stopper layer, but at a much lower cost. This gasket also has embossments around the coolant and oil passages and has a thick aluminum flake coating. All of these features result in a steel shim head gasket that handles extreme cylinder pressures very well. It’s probably the best steel shim head gasket you could ask for. Sold individually.

Product Features:
  • Embossed steel with aluminum flake coating
  • Solid metal over metal fold at the combustion seal
  • Embossed seals at coolant and oil passages
  • Approximately .020″ compressed thickness
  • For high performance street, drag race and oval track use.
See More

Most Popular 1967 Mercury S-55 Performance Fuel Systems

Customize your Mercury with 2 Performance Fuel Systems products like Performance Carburetors, all priced under $428.99.

Edelbrock – Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1406)

Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

from

$428.99
The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Electric Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)

Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$394.99
The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Top Picks for 1967 Mercury S-55 Performance Ignition Products

Upgrade Mercury S-55s with top-quality Performance Ignition Products parts, including 4 OEM and aftermarket selections for your 1967 model.

Mallory – Unilite Ignition Module (Part No.605)

Unilite Ignition Module

from

$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:
  • Service Part
  • No Moving Parts To Wear Out
  • Self Contained Unit
  • Can Drive OEM
  • Can Drive High Performance Ignition Coils
See More

Mallory – Distributor Wiring Harness (Part No.29349)

Distributor Wiring Harness

from

$30.49


Product Features:
  • Service Part
  • Makes Connections Quick And Easy
See More

Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

Promaster Classic Series; Ignition Coil

from

$186.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:
  • Glass Filled Polyester Case
  • Longer Spark Duration
  • Increased Performance
  • No Energy Loss Due To Arcing
  • Includes Brass Contact Terminal
See More

Accel – Contact Set Hp 32 Oz (Part No.110228)

Contact Set Hp 32 Oz

from

$48.49
Heavy duty points sets are quipped with extra think contack arms to prevent flexing at high RPMS. Large radiused tungsten contants provide crisp circuit breaking for peak coil output. High strength phenolic rubbing blocks provide superior durability when used with heavy duty spring tension.

Product Features:
  • Extra Thick Contact Arms
  • Large Radius Tungsten Contacts
  • High Strength Phenolic Rubbing Blocks
  • Prevents Points Float
  • Moisture-Proof Buna-N Condenser
See More

In-Demand Performance Distributors for 1967 Mercury S-55s

Select from 2 premium Performance Distributors parts for your 1967 Mercury S-55, with prices ranging from $13.29 to $569.99.

Mr. Gasket – Chrome Distributor Hold-Down Clamp (Part No.9860)

Chrome Distributor Hold-Down Clamp

from

$13.29
Chrome plated steel. Includes hold-down bolt or stud. Holds the distributor in place for accurate timing. Serrated bottom prevents the distributor from turning.

Product Features:
  • Rolled Edges For Strength
  • Ideal For Magnetos
  • Ideal For Ignition Distributor
See More

MSD Ignition – Distributor; Ford FE; Ready-to-Run (Part No.8595)

Distributor; Ford FE; Ready-to-Run

from

$569.99
MSD is excited to offer two Ready-to-Run distributors for two classic Ford engines! These distributors are the answer to weak breaker points or rebuilt aftermarket models. Inside the billet housing there is a high-output ignition module. When the maintenance-free magnetic pick-up signals the module to fire, up to 7.5 A is sent to the coil where a powerful spark is created. This improved spark output results in quick starts, snappy throttle response and terrific drivability. The distributors are equipped with a vacuum advance canister for cruising economy. Plus, there is a mechanical advance assembly that is mounted on top of the distributor shaft making it easy to adjust the advance to meet your needs. Another great feature of the Ready-to-Run distributors is their simple installation! All you need to do is connect three wires and you’ll be cruising!

Product Features:
  • Simple and clean three wire installation
  • CARB E.O. Approved
  • Does not require an MSD Ignition Control
  • Supplied w/small dia. cap w/HEI style terminals; race and rotor
  • Will accept PN[8441] Cap-A-Dapt
  • Nylon pads ensure smooth operation of the advance weights
  • Advance weight pins are staked and tig welded to the plate
  • Mech. advance assem. can be locked out for crank trigger systems
See More

Most Sold 1967 Mercury S-55 Performance Exhaust Products

Explore our best-selling Mercury parts for the 1967 S-55 among 1 OEM and aftermarket options starting from $33.49.

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1442)

Exhaust Manifold Gasket Set

from

$33.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Top-Rated Performance and Racing Products Brands For Your 1967 Mercury S-55

Shop for the best-rated brands offering Performance and Racing Products and other products for your 1967 Mercury S-55s. Below you’ll find some of our best rated Performance and Racing Products from Edelbrock, Mr. Gasket, and FEL-PRO Performance, and more. Performance and Racing Products from these brands that fit a 1967 S-55 start at just $13.29 and are rated as high as 4 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

Popular Edelbrock 1967 Mercury S-55 Performance and Racing Products

When it comes to maintaining or upgrading your 1967 Mercury S-55, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Edelbrock ticks all of those boxes. We offer a wide selection of Edelbrock Performance and Racing Products, specifically designed for the 1967 Mercury S-55. With over 14 Edelbrock brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $40.99, with an average price of just $574.35. Plus, with over 66 customer reviews and an average rating of 4 stars, you can trust that our Edelbrock Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

Performer RPM Carb/Plate Nitrous Systems Square-Bore Carbs (100-250 Hp)
from
$875.99
This product is not rated

Performer RPM Carb/Plate Nitrous Systems Square-Bore Carbs (100-250 Hp)

“”

Popular Mr. Gasket 1967 Mercury S-55 Performance and Racing Products

Mr. Gasket auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1967 Mercury S-55 owner should feel confident when installing genuine Mr. Gasket parts in their vehicle. To ensure the best fit and performance for your 1967 S-55, Advance Auto Parts carries a full inventory of 4 Mr. Gasket Performance and Racing Products. Plus you will be keeping your Mercury in peak condition while saving money because prices on these Mr. Gasket Performance and Racing Products range from $13.29 to $40.19, plus, with more than 20 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

Head Gasket
from
$37.59
This product is not rated

Head Gasket

“”

Chrome Distributor Hold-Down Clamp
from
$13.29
This product is not rated

Chrome Distributor Hold-Down Clamp

“”

Intake Gasket
from
$40.19
This product is not rated

Intake Gasket

“”

FAQs for 1967 Mercury S-55 Performance and Racing Products

Which Performance and Racing Products are best-sellers for 1967 Mercury S-55s?

Out of 36 Performance and Racing Products that fit 1967 Mercury S-55s, the following parts are the top sellers:

What’s the price range for 1967 Mercury S-55 Performance and Racing Products?

Performance and Racing Product prices for the 1967 Mercury S-55 start at $7.69 and go up to $1,114.99 for the most premium parts.

What’s the average price of a Performance and Racing Product for a 1967 Mercury S-55?

The average price for Performance and Racing Products for the 1967 Mercury S-55 is $324.43. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Performance and Racing Products for other Mercury S-55 model years?

Yes, we currently carry Performance and Racing Products for 1 model years of Mercury S-55s between 1966 and 1966. Performance and Racing Products are bought most frequently for the following model years: 1966.

What are the cheapest Performance and Racing Products for my 1967 Mercury S-55?

The cheapest 1967 Mercury S-55 Performance and Racing Products we carry in stock are:

Can I get help with 1967 Mercury S-55 Performance and Racing Product orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Mercury Performance and Racing Products and more.

What is your return policy for Mercury S-55 Performance and Racing Products?

Advance Auto Parts keeps returns simple. For new Mercury S-55 Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.