1967 GMC K15/K1500 Suburban Performance and Racing Products

Essential 1967 GMC K15/K1500 Suburban Performance and Racing Products

Holley – Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80670)

Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny

from

$620.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.

Product Features:
  • Vibratory Polished For Good Looks
  • Optimized Street Calibration That Works Out Of The Box
  • Factory Preset Electric Choke For Easy Startups
  • Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
  • No Unnecessary Trips Back To The Parts Store
  • Limited Lifetime Warranty
  • 100% Wet Flow Tested By Holley Technicians
  • Arrives Ready To Run
See More

B & M – Automatic Shifter, Sport Shifter (Part No.80776)

Automatic Shifter, Sport Shifter

from

$329.99
The B&M Sport Shifter features, Neutral safety switch, backup light switch, lighted gear indicator and black T-Handle and cable. Fits Most 3 and 4 Speed applications.

Product Features:
  • Base Trims For Custom Fit
  • Neutral Safety Switch
  • Backup Light Switch
  • Lighted Gear Indicator
  • Black T-Handle and Cable
See More

Fram – High Performance Spin-on Oil Filter: Ideal for Racing Oil (Part No.HP4)

High Performance Spin-on Oil Filter: Ideal for Racing Oil

from

$16.99
FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.** 

Product Features:
  • Proven protection for up to 10,000 miles
  • Engineered for use with synthetic or conventional motor oils
  • Filter media is a blend of fiber and resin that captures 95% of the dirt particles
  • The perfect balance of dirt-trapping efficiency and dirt-holding capacity
See More

Mr. Gasket – Chrome Plated Steel Crankshaft Pulley (Part No.4972)

Chrome Plated Steel Crankshaft Pulley

from

$61.99
Replace your stock black engine pulleys with a pair of chrome plated steel pulleys from Mr. Gasket. The pulleys are highly polished then chrome plated. Designed for small and big block Chevrolet engines with 5/8 inch water pump shaft.

Product Features:
  • Highly Polished For Lasting Beauty
  • Single Groove
  • w/ 5/8 in. Water Pump Shaft
See More

Richmond Gear – Differential Ring And Pinion (Part No.49-0068-1)

Differential Ring And Pinion

from

$354.99
Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:
  • For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
  • The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
  • Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
  • Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
  • Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.
See More

Edelbrock – C-26 Small Block Chevy Dual-Quad Intake Manifold (Part No.5425)

C-26 Small Block Chevy Dual-Quad Intake Manifold

from

$504.99
Product Features:
  • Designed for 1500 to 5500 RPM Performance
  • Low Profile for Hood Clearance on Most Vehicles
  • Air-Conditioning/Front Oil Tube Bosses Included
  • Stock Alternator Brackets Do Not Fit
  • Use Edelbrock Fuel Line Kit PN[8088] w/Our Carbs
  • Carburetor Center-to-Center Dimensions = 6-7/16 in
  • Use Edelbrock Linkage Kit PN[7094] w/Our Carbs
  • Best Matched with Edelbrock 500 cfm Carburetors
See More

B & M – Shift Improver Kit For 65-87 TH400 Transmission (Part No.20260)

Shift Improver Kit For 65-87 TH400 Transmission

from

$62.99
The B&M Shift Improver Kit the easiest way to get the performance you’ve always wanted out of your automatic transmission, two modes to select from: Heavy Duty, or Street/Strip. It’s our least expensive and simplest to install kit.

Product Features:
  • Provides Crisp Shifts
  • On Any Stock Automatic Transmission
  • Eliminates Soft/Sluggish Shift
  • Eliminates Shift Overlap
  • Eliminate Clutch and Band Wear
  • Improves Transmission Life
  • Transmission Removal Not Required
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1804)

PERFORMANCE OIL PAN GASKET SET

from

$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – TIMING CHAIN (Part No.7844)

TIMING CHAIN

from

$29.99
Product Features:
  • Timing Chain Only
See More

Mr. Gasket – Valve Cover Gasket Set (Part No.179)

Valve Cover Gasket Set

from

$36.99
Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.brbrThese gaskets are .312 inch thick. That’s substantially thicker than stock which can allow for additional valve train clearance. brbrFits Chevrolet 262,265,267,283,307,327,350,400 Gen I Small Block with Perimeter Bolt Valve Covers.

Product Features:
  • Provides Excellent Flange Sealing And Durability
  • For High-Performance Street, Drag Race & Oval Track Use
See More

Competition Cams – Xtreme Energy 250/256 Hydraulic Flat Cam and Lifter Kit Chevrolet Small Block (Part No.CL12-254-3)

Xtreme Energy 250/256 Hydraulic Flat Cam and Lifter Kit Chevrolet Small Block

from

$321.99
SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Xtreme Energy: Pro Street/bracket, needs good intake, headers, gear and 3300+ stall.

Product Features:
  • Cam and lifter kit for Small Block Chevy engines
  • CL-Kit includes cam, lifters, assembly lube, instructions and decals
  • HYDRAULIC – Xtreme Energy: Pro Street/bracket, needs good intake, headers, gear and 3300+ stall.
  • 294/306 Advertised Duration, 250/256 Duration @ .050″, .519″/.523″ Lift, 110 Lobe Separation
  • Valve spring upgrade required
See More

Mr. Gasket – Alternator Bracket (Part No.5171)

Alternator Bracket

from

$37.69
These brackets are made from heavy gauge steel, polished to a high luster, then chrome plated for lasting beauty, Similar in design to OEM units, these brackets can be adapted to other engines.

Product Features:
  • Replaced GM # 6262956
  • Polished To High Luster
  • Chrome Plated For Lasting Beauty
See More

Edelbrock – Signature Series Valve Covers: Big Block Chevy 396-502 1965 &Up, Chrome Steel (Part No.4680)

Signature Series Valve Covers: Big Block Chevy 396-502 1965 &Up, Chrome Steel

from

$83.99
The Edelbrock #4680 Signature Series Valve Covers are designed for Chevrolet 396-502 V8 ’65 & later applications. Engineered for function and styled for great looks, Signature Series valve covers have stock-style breather baffles that prevent oil passage to the PCV valve. These quality valve covers accept all emissions equipment, including PCV valve holes. Rubber grommets for the breather and PCV valve holes are included. Matching breathers sold separately.

Product Features:
  • Big Block Chevy 396-502 1965 & Up
  • Tall
  • Chrome Steel
  • Set Of Two
  • Rubber Grommets For Breather
See More

Holley – Mechanical Fuel Pump (Part No.12-835)

Mechanical Fuel Pump

from

$124.99
Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:
  • Street Performance
  • Flows 80 gph Free Flow
  • Shutoff Pressure Pre-Set 7.5 PSI
  • Fuel Pressure Regulator Is Not Required
  • Heavy Duty Construction For Continuous High rpm Operation
  • Fuel Body Casting Can Be Rotated For Plumbing Situations
  • Inlet And Outlet Tapped For 1/4 in. NPT
See More

Edelbrock – Water Pump Big-Block Chevy Short/Standard in Polished Finish (Part No.8860)

Water Pump Big-Block Chevy Short/Standard in Polished Finish

from

$474.99
Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:
  • Maximum Cooling for Street and Racing Engines
  • Internal Passages Are Balanced for Maximum Flow
  • Impeller is Larger than Others For Max Pressure
  • Impeller Vanes Dramatically Increase Flow Rates
  • Equal Distribution to Both Sides of Block
  • Only Flows in One-Direction for Optimum Efficiency
See More

Mr. Gasket – Thermocap Radiator Cap (Part No.2470R)

Thermocap Radiator Cap

from

$48.09
The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:
  • Indicates coolant temperature
  • Helps prevent coolant injuries
  • Fahrenheit and centigrade readings
  • Color-coded temperature ranges
  • Integrated coolant reclamation valve
  • Improves under-hood appearance
  • Chromed crown with a colored trim ring
See More

B & M – Torque Converter, Nitrous Holeshot 3000 (Part No.20481)

Torque Converter, Nitrous Holeshot 3000

from

$766.99
Nitrous Holeshot Converters are Built with the same features as the other B&M Holeshots, with the addition of anti-balloon plates. The anti-balloon plates will allow these converters to stand up to the instant horsepower nitrous delivers.

Product Features:
  • 2800-3200 RPM
  • Small And Big Blocks
  • Serious Performance
  • Furnace Brazed
  • Fully Balanced
See More

Energy Suspension – Transfer Case Torque Mount (Part No.3.1107R)

Transfer Case Torque Mount

from

$27.99
Product Features:
  • Transfer Case Torque Mount
See More

Motive Gear – Differential Mini Spool (Part No.MS12C)

Differential Mini Spool

from

$108.99


Product Features:
  • MINI SPOOL GM12 BOLT CAR & TRUCK STRANGE # 088430
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9730)

Performer Series Retainer (Qty 16)

from

$99.99
Product Features:
  • Use W/ Valve Springs Part #5703, 5794
  • Set of 16
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

Mr. Gasket – Ultra Seal: Exhaust Gasket Set (Part No.5901)

Ultra Seal: Exhaust Gasket Set

from

$31.99
Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:
  • Withstands Intense Exhaust Heat
  • Graphite-Impregnated Facing
  • Steel Expanded Metal Core
  • Superior Tensile Strength
  • Resists Deteriorating
  • Anti-stick Properties
  • Easy Removal For Disassembly
See More

Competition Cams – CAMSHAFT, BBC 280 MAGNUM HYD 1 EA (Part No.11-208-3)

CAMSHAFT, BBC 280 MAGNUM HYD 1 EA

from

$247.99
An older member of the COMP Cams grind family, the Magnum series of camshafts offers excellent performance gains over stock without the added wear and tear associated with more aggressive camshafts. Ideal for use with higher compression ratio engines that

Product Features:
  • Best with aftermarket torque converters and 9.5:1 compression.
  • Great high RPM power.
  • Easy on valve train parts.
  • Can be used with mild ratio rocker arms and traditional performance valve springs.
See More

Mr. Gasket – Chrome Plated Engine Oil Pan (Part No.9779)

Chrome Plated Engine Oil Pan

from

$153.99
Beautifully chrome plated. Complete with drain plug, washer & bolts (stock depth). Chrome-plated dipsticks with tubes sold separately.

Product Features:
  • Chrome plated
  • Includes drain plug/washer/bolts
See More

Mr. Gasket – Lts Throttle Cable Brkt Chev (Part No.9885)

Lts Throttle Cable Brkt Chev

from

$14.99
The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.

Product Features:
  • 2 in. adjustable range
  • Includes necessary hardware
  • Chrome plated
  • Individually packaged
See More

Mallory – Unilite Ignition Module (Part No.605)

Unilite Ignition Module

from

$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:
  • Service Part
  • No Moving Parts To Wear Out
  • Self Contained Unit
  • Can Drive OEM
  • Can Drive High Performance Ignition Coils
See More

Mr. Gasket – Intake Manifold Bolts (Part No.6091)

Intake Manifold Bolts

from

$32.09
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:
  • Features 12-point Smaller-than-standard Bolt Head
  • Thick Flat Washers Distribute Optimum Clamp Load
  • Ideal Use Where Space Is Minimal On Race Manifolds
  • Bolts And Washers Zinc Plated For Protection
  • Zinc Plated For Protection
See More

Competition Cams – Engine Valve Spring Kit (Part No.911-16)

Engine Valve Spring Kit

from

$759.99
Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.O.D. Dia. 1 I.D. Dia. 2 Damper Seat Load Open Load Coil Bind Rate (Lbs./In.) Titanium Retainer Steel Retainer Cup Seat Shims 1.524 1.110 Y 122 @ 1.900 309 @ 1.400 1.200 373 721, 732 1732, 741 4779* 4757

Product Features:
  • Seat pressure: 122 lbs. @ 1.900″, Open Pressure: 309 lbs. @ 1.400″
  • O.D.: 1.524″, I.D.: 1.110″
  • Single valve springs with damper
See More

Mr. Gasket – Ultra Seal: Intake Gasket (Part No.5822)

Ultra Seal: Intake Gasket

from

$34.99
Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Silicone beading on both sides of each gasket
  • Complete with manifold end seals and distributor gasket
  • For OE replacement, high performance street, drag race and oval track use
  • Creates Tight Leak proof Seal
See More

1967 GMC K15/K1500 Suburban Performance and Racing Products

You count on your 1967 GMC K15/K1500 Suburban to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 92 Performance and Racing Products ranging in price from $7.99 to $1,009.99, you’re sure to find everything you need for your 1967 GMC K15/K1500 Suburban.

Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 16 different brands like K&N, Edelbrock, and FEL-PRO Performance. 1967 GMC K15/K1500 Suburban Performance and Racing Products start as low as $7.99!

One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 321 extensive product reviews on 1967 GMC K15/K1500 Suburban Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Intake Manifold Bolts with 4.6 stars and Performer Carburetor #9906 600 CFM With Electric Choke, Satin Finish (Non-EGR) with 3.8 stars.

Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1967 GMC K15/K1500 Suburban below to get started!

Top-Rated Performance and Racing Products Brands For Your 1967 GMC K15/K1500 Suburban

Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1967 GMC K15/K1500 Suburban running right for years to come. In our inventory you’ll find brands like K&N, Edelbrock, FEL-PRO Performance, and even more.

Popular Flowtech Performance and Racing Products

You’ll find popular Flowtech brand products across Performance Exhaust Products. All are waiting to get your 1967 GMC K15/K1500 Suburban back on the road. Some of the top-rated Flowtech products in these categories are:
Real-Seal; Header Gasket
from $85.39
(1)
Real-Seal; Header Gasket
Performance Exhaust Manifold Gaskets

Top-Rated Edelbrock Performance and Racing Products


If Edelbrock are what you’re looking for, our inventory holds plenty. We stock Edelbrock brand Performance and Racing Products for your 1967 GMC K15/K1500 Suburban, and some of our most reviewed Edelbrock parts include:
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
from $195.99
(7)
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
Performance Intake Manifolds

FAQs for 1967 GMC K15/K1500 Suburban Performance and Racing Products

What are the most purchased Performance and Racing Products for the 1967 GMC K15/K1500 Suburban?

Out of 92 Performance and Racing Products for the 1967 GMC K15/K1500 Suburban, the most popular in our inventory are:
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
from $39.49
(1)
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
Performance Engine Cylinder Head Gaskets

What are the top-rated 1967 GMC K15/K1500 Suburban Performance and Racing Products?

Top-rated Performance and Racing Products for your 1967 GMC K15/K1500 Suburban based on customer reviews/ratings are:
Intake Manifold Bolts
from $32.09
(5)
Intake Manifold Bolts
“Excellent product.”
Performer Carburetor #9906 600 CFM With Electric Choke, Satin Finish (Non-EGR)
from $397.99
(5)
Performer Carburetor #9906 600 CFM With Electric Choke, Satin Finish (Non-EGR)
“easy to install all the gaskets and parts came with it”
Performer RPM Series fuel pump for SBC and W Series Chevy
from $168.99
(5)
Performer RPM Series fuel pump for SBC and W Series Chevy
“Items received quickly, looks like thier 20 years old”