from

$257.99

Product Features:

CHRY 10BLT 8.75 EARLY R/P 3.73 MGP 29SP USE MG7260-C875/MG1350-C87529

from

$163.99

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

Bolt-on Performance
Custom Fit For Make And Model Listed
Wires Are Pre-Cut To Exact Specifications
Conductor core features DuPont Kevlar material for increased tensile strength
Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately

from

$521.99

Edelbrock part #21763 Performer intake manifold is designed for street 318-340-360 c.i.d. Chrysler V8’s. This manifold is not for use on marine engines used in salt water. Will not fit 1992 and later Magnum engines. This manifold offers a durable black po

Product Features:

Idle-5500 RPM Range
Dual Plane Type-4150 Style Flange
4.13 in. Front Height, 4.63 in. Center Height, 5.13 in. Rear Height
Black Powder Coated Finish
Non-EGR

from

$64.99

Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for 1965-1991 Chrysler 273-318-340-360 engines, this valve cover features chrome-plated steel construction and a smooth design. Sold in pairs, this stock profile cover is baffled to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:

Designed for 1965-1991 Chrysler 273-318-340-360 engines
Baffled for breather system compatibility
Sold in pairs
Triple chrome-plated steel construction
Stock height
Features OEM style sealing edge

from

$149.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1962-up TF727 transmissions and all internally balanced Chrysler, Dodge and Plymouth V8 engines with 6-bolt crankshaft flange. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.00 or 11.125 inch converter mounting locations and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$25.99

These high performance thermostats are designed to resist large variations in coolant pressures that occur at high RPM’s where coolant temperature and coolant pressure fight for control of the thermostat keeping it from opening at its designated temperature. The balanced HP thermostat features all brass and copper construction, and opens at the right temperature regardless of engine RPM.

Product Features:

High performance
Resists variations in coolant
Brass and copper construction
Opens at right temperature

from

$2198.99

The Edelbrock #5093 E-Street cylinder heads are designed for use with 1961-1979 Chrysler 361-440 c.i.d. Wedge engine applications. The Edelbrock E-Street cylinder heads offer American made quality and affordable performance. E-Street cylinder heads featur

Product Features:

Complete Pair For Hydraulic Flat Tappet
84cc Combustion Chamber Volume
210cc Intake/70cc Exhaust Runner Volume
2.14 in. Intake/1.81 in. Exhaust Valve Diameter
0.625 in. Deck Thickness

from

$71.99

If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:

Improved output coil for electronic ignitions
Works w/Blaster Ignition Or MSD 5/6/7 Series
Ballast Resistor Required If Used w/Stock Points Ignition
Alkyd tower w/high dielectric properties lessens carbon tracking

from

$25.99

This Spectre Alternator Bracket Kit is a two piece set designed to fit Chrysler 318-340-360 small block engines. Featuring a triple chrome-plated finish and high quality steel construction, this kit is an OEM replacement that includes two pieces.

Product Features:

Fits small block Chrysler 318-340-360 engines
Manufactured from high quality steel
Kit includes two pieces
Features a triple chrome-plated finish
Factory replacement

from

$357.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$43.49

This Spectre Timing Cover Kit is designed to protect components like timing gears and the chain or belt. It featurings triple chrome plated steel construction. Timing cover kits are engineered for optimum fit and function.

Product Features:

Triple chrome plated
Steel construction
OEM replacement
OEM fit & function

from

$379.99

Our advanced power system line has grown to include starters. Our new APS starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The APS starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement and thousands of starts. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.

Product Features:

Mount Can Be Clocked To Assist In Mounting
Downsized design helps clearance issues w/oil pans and exhaust
Ball bearing supported armature and pinion gear
3 Hp Motor Provides Power For High Compression Engines
Gear reduction of 4.4:1 improves torque for great cranking
Downsized design helps clearance issues
Mount can be clocked to assist in mounting

from

$79.99

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

More Accurate Ignition Timing
Improves Performance
Provides More Accurate Ignition Timing
Easy To Install w/Hand Tools
Reduced Maintenance
Thermal Clad Based Surface Mount Construction
Utilizes Specialized Electronic Circuitry
Ignition Timing Is Stable From 1 To 10000rpm

from

$128.99

Product Features:

Head: 4.505″ Bore/0.038″ Thick/9.69cc Vol.
Intake: 1.23″x2.27″ Port/.030″ Thick
Exhaust: 1.84″x1.33″ Port
3/16″ Valve Cover
Multi Piece Configuration

from

$16.99

Fuel pump mounting pad cover is used to cover the hole in the block when the mechanical fuel pump is removed to use an electric pump.

Product Features:

Mechanical Fuel Pump Mounting Pad Cover For Chrysler V-8ft.S

from

$113.99

Designed to reduce wheel shimmy and end vibration caused by larger tires, the Rancho® steering stabilizer kit cuts down on steering arm fatigue to improve handling. The kit includes one Rancho RS5000® steering stabilizer and installation brackets.

Product Features:

COMPATIBILITY — Designed for a variety of trucks and SUVs from Chevrolet®, GMC®, Ford®, Dodge®, Jeep®, Plymouth® and International®
IMPROVED HANDLING AND PERFORMANCE — Reduces wheel shimmy, bump steer and vibration which helps minimize on- or off-road driver fatigue
ACCOMMODATES LARGER TIRES — Engineered for vehicles with oversized wheels and tires.
ENGINEERED TO LAST — Features protective boot to shield shock rod and oil seal and 0.25-in. high-strength, low-alloy steel bracket construction for long life
EASY TO INSTALL — Includes one Rancho RS5000® steering stabilizer and brackets that bolt directly to factory steering linkage with included mounting hardware, no modifications needed
RESISTS CORROSION — Durable black powder-coated and/or zinc-plated brackets resist rust and corrosion
PRECISION DESIGN — Brackets are CNC cut and bent to exact specifications for a perfect fit

from

$16.99

FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.**

Product Features:

Proven protection for up to 10,000 miles
Engineered for use with synthetic or conventional motor oils
Filter media is a blend of fiber and resin that captures 95% of the dirt particles
The perfect balance of dirt-trapping efficiency and dirt-holding capacity

from

$30.99

Thick, molded rubber with steel carrier. Manufactured from high-density cork and rubber blend gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage. Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Available in standard or extra thick to provide additional valve train to cover clearance. For OE replacement, high performance street, drag race and oval track.

Product Features:

Made from cork/rubber compound
Can be reused many times
Thick; fuel-resistant

from

$455.99

The industry standard with adjustable mechanical advance curve. Triggered by photo-optic infrared LED system. Improved combustion efficiency and economy, increased spark plug life and cold weather starting, and maintenance free operation.

Product Features:

Improved Combustion And Economy
Increased Spark Plug Life
Improved Cold Weather Starting
Maintenance Free Operation
Accurate Spark Timing
Self-Lubricating Bushings
Years Of Trouble-Free Service

from

$25.99

Product Features:

Service Part
Makes Connections Quick And Easy

from

$30.99

Mr. Gasket has three types of exhaust gaskets–standard, Ultra Seal, and Copperseal. Use the standard for a stock rebuild and the Ultra or Copperseal for extra blowout protection.

Product Features:

Designed to provide excellent sealing and durability
Large fiber gasket material
Heat resistant
Reusable
Precision die cut for excellent fit
Limited warranty

from

$125.99

Kits include most popular chrome dress-up components, including short, OEM height valve covers with integral oil baffles.

Product Features:

Includes oil baffles
Chrome plated

from

$19.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$23.79

Spectre’s Chrysler water neck fits 1964 and later Chrysler V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

Product Features:

Fits 1964 and later Chrysler V8 engines
Includes bolts
Chrome plated
Easy to install
O-ring/gasket not included

from

$18.99

Oil Pan Bolt Kit

from

$467.99

The B&M Megashifter has it all, form, function and classic style. This all adds up to bring you a quality shifter that’s been one of the most popular automatic shifters of all time. The light truck Megashifter is better suited for truck and bench seat applications with its overall height of 14.85-inches tall (2.25-inches taller than #80690 Megashifter.) The positive ratcheting action won’t allow you to over-shift and miss a gear at that critical moment, along with the reverse lockout feature meets NHRA/IHRA safety rules for those weekend grudge races at the track, while the look and feel of the T-handle and accordion style shift boot really shows off its racing heritage. Other features include a black console that you can trim to match the contour of your vehicle’s floor, 5-foot long shifter cable, cable brackets, transmission shift levers, chrome plated top plate with lighted gear indicator and everything needed for an easy at home installation. An optional T-handle with a 12-volt button is available separately for actuating a trans-brake, nitrous oxide or other accessories for the hard-core performance enthusiast. This shifter fits most popular Chrysler, Ford and GM 3 and 4-speed automatic transmissions. Note: AOD transmissions require optional kit #40496, GM 4L60E through 4L85E transmissions with PRNDL switch will require optional kit #70499. Overall Dimensions – 14.9L x 6.4W x 14.8H

Product Features:

Universal Floor Mount Application
Cable Operated
Quick Installation
Accurate Shifting
NHRA/IHRA Reverse Lockout Meets Requirements
Use w/Reverse Pattern Valve Body
Includes Neutral Safety Switch
Includes Backup Light Switch

from

$498.99

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some Holeshots.

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$48.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.