from

$271.99

Polished aluminum replacement cover for Dana 60 (standard rotation only).

Product Features:

Fits standard rotation Dana Spicer 60
Finned polished aluminum

from

$8.99

Ring gear bolt for Chrysler 7.25″, 8″ IFS, 8.25″, 8.75″ & GM 7.2″ IFS front. 3/8″ x 24.

Product Features:

Ring gear bolt for Chrysler 7.25″, 8.0″ IFS and 8.75″
3/8″ x 24 thread
.866″ long

from

$10.99

Crush Sleeve for Model 35, Chrysler 7.25″, 8.25″ Ford 8″ & GM 7.75″. Approx 0.495″ long.

Product Features:

Crush sleeve for AMC Model 35, Chrysler 7.25″ and 8.25″, Ford 8″ and GM 7.75″
0.495″ tall

from

$401.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits Chrysler 8.75″ “41” case housing
8.75″ ring gear diameter
29 spline pinion
12 ring gear bolts
3.73 ratio

from

$209.99

USA Standard Gear open spider gear set for Chrysler 8.25″, 27 spline .

Product Features:

Spider gear kit
Fits Chrysler 8.25″ 27 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$19.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$336.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Dana Spicer 60 front
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, axle seals, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil baffles and slingers, thread locker, marking compound with brush and gasket.

from

$8.29

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$59.99

RngPnnInstlKt

from

$16.99

7.25″ & 8.25″ Chrysler pinion seal.Yukon Mighty seal.

Product Features:

Pinion seal
Fits Chrysler 7.25″ and 8.25″

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$5.99

Chrysler 8.75″ (coarse spline) pinion nut. 3/4″ x 16.

Product Features:

Pinion nut
Fits Chrysler 8.75″ with 10 spline pinion

from

$4.99

Pinion gear thrust washer for 8″ and 9″ Ford, Model 20, and 7.25″ Chrysler.

Product Features:

Pinion gear thrust washer for Ford 8″, Ford 9″ and Chrysler 7.25″

from

$4.99

Product Features:

Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
Fits standard open differentials only

from

$252.99

Yukon 1541H alloy rear axle for Chrysler 8.75″ measuring 28″ with 30 splines and 5×4.5 bolt pattern. for use with A-Body only. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with

Product Features:

Fits Chrysler 8.75″
30 spline
28″ long
5 x 4.5″ bolt pattern

from

$295.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 60 rear
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$450.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$13.79

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$9.99

Chrysler 8.75″ (coarse spline) pinion nut washer.

Product Features:

Pinion nut washer
Fits Chrysler 8.75″ with 10 spline pinion

from

$369.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

Fits Chrysler 8.75″ ’41’ case housing with LM104912 carrier races
Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, thread locker, marking compound with brush, and gasket.

from

$41.49

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$565.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$23.99

Product Features:

Cross pin shaft
Fits Dana Spicer 60

from

$181.99

Dana 60 & Dana 70 Power Lok clutch set (steel & fiber).

Product Features:

Clutch kit
Fit Dana Spicer 60, 70, 70U and 70HD Powr Lok positraction

from

$234.99

Yukon standard open spider gear kit for 7.25″ Chrysler with 25 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Chrysler 7.25″ rear with open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.