1967 Dodge Dart Differentials

Product Features:

• Nodular iron for added strength
• Thick design
• Durable powder coat finish
• Magnetic drain plug
• Made in USA
• High strength stainless steel fasteners

Pinion seal for 8.75″ Chrysler or for 9.25″ Chrysler with 41 or 89 housing.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Chrysler 8.75″ with ’41’ and ’89’ case housings and 2000 and down Chrysler 9.25″

Yukon 1541H alloy cut to fit rear axle for Chrysler 8.75″ measuring 28″-32″ with 30 splines and 5×4.5 bolt pattern. for use with A, C & E-Body. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. Must use Green bearing.

Product Features:

• Fits Chrysler 8.75″
• 30 spline
• Cut to length design fits 28″-32″ applcations
• 5 x 4.5″ bolt pattern

Yukon standard open spider gear kit for ’96 and older 8.25″ Chrysler with 27 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Chrysler 8.25″ open differntial with 27 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Cross pin shaft for Chrysler 7.25″.

Product Features:

• Cross pin shaft
• Fits Chrysler 7.25″

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

• Includes four quarts of Redline Shockproof oil

Product Features:

• Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
• Fits standard open differentials only

Differential carrier side bearing screw adjuster for Chrysler 7.25″ and 8.25″.

Product Features:

• Side adjuster
• Fits Chrysler 7.25″ and 8.25″

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Product Features:

• Spider gear kit
• Fits Dana Spicer 60, 35 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits Dana Spicer 60 rear
• Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.

Product Features:

• Fits Chrysler Dana Spicer 60 with 35 spline axles
• 4.56 and up ratio only
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

Chrysler 8.75″ (coarse spline) pinion nut washer.

Product Features:

• Pinion nut washer
• Fits Chrysler 8.75″ with 10 spline pinion

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Chrysler 7.25″
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

89 housing nodular Iron Drop Out case, up to 500 HP, Billet adjuster for 8.75″ Chrysler. This dropout does not come with fill plug (Part number CHY612017).

Product Features:

• Fits Chrysler 8.75″
• ’89’ case design
• Nodular iron for added strength

Spartan spring & pin kit, fits larger designs.

Product Features:

• Fits Dana Spicer 60
• Replacement alignment pin and spring kit

Yukon round replacement yoke companion flange for Dana 60 and 70. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 60 and 70
• 29 spline
• 5.00″ O.D.
• 8 x 4.25″ bolt pattern
• Round companion flange

Product Features:

• BUILT TO LAST: Advanced heat treatment process for strength
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
• RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Product Features:

• MINI INSTALL KIT CHRYSLER 8.25 8 1/4″

8.75″ Chrysler & 55P Chevy Power Lok clutches, Model 20 also, POSI.

Product Features:

• Clutch kit
• Fits Chrysler 8.75″, 1955-1964 GM passenger car and AMC Model 20 Powr Lok positraction

Ring gear bolt for Chrysler 7.25″, 8″ IFS, 8.25″, 8.75″ & GM 7.2″ IFS front. 3/8″ x 24.

Product Features:

• Ring gear bolt for Chrysler 7.25″, 8.0″ IFS and 8.75″
• 3/8″ x 24 thread
• .866″ long

M804049 set-up bearing (one bearing). No return.

Product Features:

• Set up bearing
• Fits HM804049 pinion bearing
• Easily slips on and off pinion journal to allow for pinion depth adjustment

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

• Redi-Sleeve yoke saver
• Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

• Fits Chrysler 8.75″ ’89’ case housing with 25520 carrier races
• Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , thread locker, marking compound with brush, and gasket.

Pinion gear thrust washer for 8″ and 9″ Ford, Model 20, and 7.25″ Chrysler.

Product Features:

• Pinion gear thrust washer for Ford 8″, Ford 9″ and Chrysler 7.25″

Replacement crush sleeve for Dana 60, APROX 0.660″ long.

Product Features:

• Crush sleeve for Dana Spicer 60
• 0.660″ tall