from

$5.99

Product Features:

Outer oil slinger for Dana Spicer 60, 70, 70U and 70HD

from

$36.99

Product Features:

Belleville plate, splined
Fits Dana Spicer 44 Powr Lok

from

$234.99

Yukon 1541H alloy 5 lug rear axle for GM 12T and 8.5″ 2WD van with a length of 33-3/8″ inches and 30 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a C-clip.

Product Features:

Fits GM 12 bolt truck with 2 wheel drive and van
30 spline
33 3/8″ long
5 lug

from

$21.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$18.99

1310 & 1330 U/joint strap, Dana 30, Dana 44, Model 35, & 9.25″ w/bolts.

Product Features:

u-joint strap kit
Fits Dana Spicer 30 and 44, AMC Model 35 and Chrysler 9.25″
1310 and 1330 u-joint size
Includes two straps and four bolts

from

$4.99

3/8″ ring gear bolt washer for GM 12 bolt car & truck, 8.2 BOP & more.

Product Features:

Ring gear bolt washer for GM 12 bolt car and truck, 1955-1964 passenger car, 1963-1979 Corvette and 8.2″ Buick, Oldsmobile and Pontiac

from

$18.49

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$832.99

Yukon replacement positraction internals for Dana 60 and 70 with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit includes clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Clutch kit
Fit Dana Spicer 60 Powr Lok positraction with 35 spline axles
Smooth design
Includes two side gears, four pinion gears, cross pin shafts and side gear thrust washers.

from

$3.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$12.99

12T cover gasket.

Product Features:

Cover gasket
Fits GM 12 bolt truck

from

$249.99

Product Features:

Installation kit
Includes o-ring for bulkhead fitting, bulkhead fitting, outer fitting, switch, front and rear switch cover, solenoid, zip ties and 20′ air line

from

$32.99

Product Features:

Bearing retainer
Fits Dana Spicer 44 in Jeep TJ
1 5/8″ x 3 3/16″ bolt pattern
3/16″ bolt holes

from

$14.99

Positraction pinion gear thrust washer with step-lip inside for GM 12P and 12T. fits new Eatons.

Product Features:

Pinion gear thust washer for GM 12 bolt passenger car and truck
Fits positraction designs only
Has inside lip

from

$10.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$32.99

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$5.29

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 87-97; GMC 67-05; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2012
Weight approx: 1 Lbs
CUSHION INSERT ONLY
FOR COMPLETE MOUNT SEE PART 6056

from

$232.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits GM 12 bolt truck
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$163.99

Product Features:

GM 8 7/8″ OPEN INTERNAL KIT CAR & TRUCK

from

$27.49

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$146.99

Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1330 U/joint size. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 30 and 44
26 spline
1330 u-joint size
Outside snap ring design
3.625″ snap ring span
1.062″ cap diameter
Strap style

from

$12.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$305.99

Yukon positraction internals for GM 12P and 12T with 33 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits GM 12 bolt passenger car with 33 spline Dura Grip positraction
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$7.99

Wheel Lug Stud

from

$8.99

C/Clip for Chrysler 8.25″, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 8.2″, 8.5″ & 8.6″.

Product Features:

c-clip for Chrysler 8.25″, Ford 8.8″, GM 12 bolt car and truck and GM 8.2″, 8.5″ and 8.6″
.150″ thick

from

$14.99

Dana 60 semi-float C-clip.

Product Features:

C-clip
Fits Dana Spicer 60

from

$28.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.