1966 Dodge Monaco Drivetrains
More 1966 Dodge Monaco Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1966 Dodge Monaco, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1966 Dodge Monaco Drivetrains
Motive Gear – Performance Differential Ring and Pinion (Part No.C887391L)
from
$264.99Product Features:
- CHRY 9BLT 8.75 LATE R/P 3.91 MGP 29SP USE MG7260-C875/MG1350-C87529
Yukon Gear – Pinion Install Kit For ’76 And Newer Chrysler 8.25" Differential (Part No.13004)
from
$159.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.
Product Features:
See More
Product Features:
- Fits 1976 and up Chrysler 8.25″
- Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.
Motive Gear – Drive Shaft Pinion Yoke (Part No.MG1310-6010)
Driveworks – Tapered Roller Bearing (Part No.S-LM-603012)
MOOG Driveline Products – Universal Joint Strap Kit (Part No.316-10)
from
$10.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.
Product Features:
See More
Product Features:
- For U-Joints 316 & 458
- Contains two 1.54″ bolt center clamps and four 1/4-28 x 5/8″ cap screws
Yukon Gear – Chrysler 8.75" (Coarse Spline) Pinion Nut Washer (Part No.33162)
from
$9.99
Chrysler 8.75″ (coarse spline) pinion nut washer.
Product Features:
See More
Product Features:
- Pinion nut washer
- Fits Chrysler 8.75″ with 10 spline pinion
Yukon Gear – The Carrier Bearing Puller (Part No.56072)
from
$883.99
The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.
Product Features:
See More
Product Features:
- Carrier bearing puller
- Works with an impact gun to safely and easliy remove carrrier bearings
Yukon Gear – Chrysler 9.25" And Dana 44 / 60 Tracloc Clutch Guide Replacement (Part No.33249)
from
$8.99
Product Features:
See More
- Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
- For Trac Loc positraction applications only
Yukon Gear – Flange Yoke For Chrysler 9.25" (Part No.41012)
from
$263.99
Yukon flange yoke for Chrysler 9.25″. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Chrysler 9.25″ rear
- 29 spline
- Round companion flange
Dorman – Differential Pinion Yoke Assembly (Part No.697-541)
from
$231.99
A worn or damaged differential pinion flange can lead to driveline vibrations and fluid leaks. This part is designed to match the performance of the original equipment pinion flange on specified vehicles. It has been engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is rusted, worn or damaged. It is made of rugged materials for reliable service and durability.
Product Features:
See More
Product Features:
- Direct replacement – this differential pinion flange is designed to match the performance of the original equipment flange on specified vehicles
- Ideal solution – engineered to help restore a secure and reliable connection between the differential pinion and the drive shaft when the original flange is worn or damaged
- Durable construction – designed and manufactured to strict specifications for reliable performance
- Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience
National – Bearings (Part No.M88010)
from
$10.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
USA Standard Gear – Chrysler 8.25" Spartan Locker Cross Pin Shaft (Part No.17035)
from
$49.99
Product Features:
See More
- USA Standard Gear heavy-duty cross pin shaft
- Fits Chrylser 8.25″ with 27 and 29 spline axles
- Works with Spartan Locker or standard open spider gears
USA Standard Gear – Powr Lok Posi For Chrysler 8.75", Aggressive Design (Part No.59026)
from
$919.99
Yukon yoke for Ford 8.8″ truck or passenger with a 1330 U/joint size. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Ford 8.8″
- 30 spline
- 1330 u-joint size
- 3.625″ snap ring span
- 1.062″ cap diameter
- Outside snap ring design
- Strap style
Yukon Gear – Yoke For Chrysler 8.75" With 10 Spline Pinion And A 7260 U/Joint Size (Part No.41006)
from
$213.99
Yukon yoke for Chrysler 8.75″ with 10 spline pinion and a 7260 U/joint size. 2.125″ snap ring span, 1.078″ cap diameter. Inside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Chrysler 8.75″
- 10 spline
- 7260 u-joint size
- Inside snap ring design
- 2.125″ snap ring span
- 1.078″ cap diameter
- Strap style
Yukon Gear – Standard Open Spider Gear Kit For ’96 And Older 8.25" Chrysler With 27 Spline Axles (Part No.16002)
from
$301.99
Yukon standard open spider gear kit for ’96 and older 8.25″ Chrysler with 27 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Spider gear kit
- Fit Chrysler 8.25″ open differntial with 27 spline axles
- Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
Yukon Gear – Positraction Spiders For Chrysler9.25" Dura Grip Posi, 31 Spline, No Clutches Included (Part No.16180)
from
$389.99
Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Spider gear kit
- Fits Chrysler 9.25″
- Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
- Fits Yukon Dura Grip
National – Shaft Repair Sleeve (Part No.99106)
from
$33.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
- Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
Yukon Gear – 1541H Alloy Rear Axle For Chrysler 8.75" (Part No.21042)
from
$252.99
Yukon 1541H alloy rear axle for Chrysler 8.75″ measuring 30″ with 30 splines and 5×4.5 bolt pattern. for use with C & E-Body only. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. Must use Green bearing.
Product Features:
See More
Product Features:
- Fits Chrysler 8.75″
- 30 spline
- 30″ long
- 5 x 4.5″ bolt pattern
USA Standard Gear – Master Overhaul Kit for Chrysler 8.75" #42 Housing with 25520/90 Differential bearings (Part No.37093)
from
$456.99
USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.
Product Features:
See More
Product Features:
- Fits Chrysler 8.75″ ’42’ case housing with 25520 carrier races
- Uses Koyo bearings and races
- Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.
National – Bearings (Part No.HM88649)
from
$21.79
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Mr. Gasket – Differential Gasket (Part No.81)
from
$19.29
Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit.
Product Features:
See More
Product Features:
- .047″ thick cellulose/nitrile composite gasket material
- Precision die cut
- Reusable
Yukon Gear – Steel Spool For Chrysler 8.75" With 30 Spline Axles (Part No.32040)
from
$264.99
Yukon Performance 2-1/16″ deck steel spool for 8.75″ Chrysler with 30 spline axles. Spool uses 2.050″ journal bearings (LM104949/12). Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Chrysler 8.75″ with 30 spline axles
- Provides 100% traction to both wheels at all times
- Not recommended for street driven vehicles
National – Bearings (Part No.M804010)
from
$25.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Yukon Gear – Steel Cover For Chrysler 8.25" (Part No.32312)
from
$159.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t
Product Features:
See More
Product Features:
- Fits Chrysler 8.25″
- Steel
Yukon Gear – Standard Open Carrier Case For ’09 & Down Chrysler 9.25" Rear (Part No.20008)
from
$261.99
Product Features:
See More
- Standard open carrier case
- Fits 2009 and down Chrysler 9.25″ rear
- Does not include spider gears
Yukon Gear – Redi-Sleeve Yoke Saver For 8.75" C, 9.25" C, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD (Part No.30228)
from
$37.99
Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.
Product Features:
See More
Product Features:
- Redi-Sleeve yoke saver
- Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD
Yukon Gear – 9.25" Chrysler C/Clip (Part No.33075)
from
$17.99
9.25″ Chrysler C/clip, 0.205″ wide for 4137429 axle.
Product Features:
See More
Product Features:
- c-clip for Chrysler 9.25″ rear
- 0.205″ thick
National – Multi Purpose Seal (Part No.9376)
from
$7.29
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Low swell in hydrocarbon fluids
- Design type: spring loaded; multi-lip
- Provides good low temperature capability
- Temperature range: -40°F to 225°F; -40°C to 107°C
- Delivers quality and reliable performance for every type of repair
Popular 1966 Dodge Monaco Drivetrains Categories
1966 Dodge Monaco Drivetrains
You count on your 1966 Dodge Monaco to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 351 Drivetrains ranging in price from $2.29 to $919.99, you’re sure to find everything you need for your 1966 Dodge Monaco.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 14 different brands like Moog, Driveworks, and National. 1966 Dodge Monaco Drivetrains start as low as $2.29!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 611 extensive product reviews on 1966 Dodge Monaco Drivetrains. Some of the top-rated Drivetrains products we carry are Multi Purpose Seal with 4.4 stars and Tapered Cone/Cup Wheel Bearing Set with 4.4 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1966 Dodge Monaco below to get started!
Top-Rated Drivetrains Brands For Your 1966 Dodge Monaco
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1966 Dodge Monaco running right for years to come. In our inventory you’ll find brands like Moog, Driveworks, National, and even more.
Popular Dorman Drivetrains
You’ll find popular Dorman brand products across Spindles. All are waiting to get your 1966 Dodge Monaco back on the road. Some of the top-rated Dorman products in these categories are:
from
$4.99
(3)
Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm
Spindle Retainers
Top-Rated MOOG Driveline Products Drivetrains
If MOOG Driveline Products are what you’re looking for, our inventory holds plenty. We stock MOOG Driveline Products brand Drivetrains for your 1966 Dodge Monaco, and some of our most reviewed MOOG Driveline Products parts include:
FAQs for 1966 Dodge Monaco Drivetrains
What are the most purchased Drivetrains for the 1966 Dodge Monaco?
Out of 351 Drivetrains for the 1966 Dodge Monaco, the most popular in our inventory are:
What are the top-rated 1966 Dodge Monaco Drivetrains?
Top-rated Drivetrains for your 1966 Dodge Monaco based on customer reviews/ratings are:
from
$13.99
(14)
Tapered Cone/Cup Wheel Bearing Set
“Advance Auto website when entering my 1989 Ford F150 doesn’t ask if it is 2 wheel or 4 wheel drive. So I had to return the first set”
