from

$21.99

Product Features:

KIT SHIM SIDE 9.5″ GM

from

$709.99

Ring and Pinion Kit

from

$251.99

Yukon replacement trail repair kit for Dana 60 with 1310 size U/joint and u-bolts. This kit comes with a yoke, U/joint, pinion seal, U/bolt or strap kit, pinion nut, and pinion nut washer (if applicable).

Product Features:

Fits Dana Spicer 60 and 70
1310 u-joint size
Kit includes yoke, U-joint, pinion seal, pinion nut and washer, U-bolts and threadlocker

from

$304.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits 1955-1964 GM passenger car and truck
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve , marking compound and brush.

from

$38.49

Product Features:

MINI INSTALL KIT GM8.2IFS 98 & ON

from

$223.99

Yukon replacement standard open spider gear kit for Dana 60 with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Dana Spicer 60 open differential with 30 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$89.99

Chrome replacement cover for Dana 60 and 61(not reverse rotation!).

Product Features:

Fits standard rotation Dana Spicer 60
Chrome

from

$11.99

Side gear thrust washer for 8.25″ GM IFS.

Product Features:

Side gear thrust washer
Fits GM 8.25″ IFS

from

$295.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 60 rear
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$215.99

Bearing race driver for Dana 60 front, Dana 70U rear, Chrysler 8.75″ with 42 housing, and ’88 and older GM 14T. No return.

Product Features:

Bearing race driver
Fits HM803110 race
All steel construction

from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$11.99

Replacement ring gear bolt for Model 35, Dana 25, 27, 30 & 44. 3/8″ x 24.

Product Features:

Ring gear bolt for Dana Spicer 25, 27, 30, 44 and AMC Model 35
3/8″ x 24 thread

from

$1302.99

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years.

Product Features:

Fits Dana Spicer 44 with 30 spline axles
3.73 and down ratio only
Forged case and 8620 internals for added strength
Works with a variety of air delivery systems
Assembled in the USA

from

$83.99

Product Features:

Seal housing for Dana Spicer 44
Includes o-rings

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$13.99

Product Features:

Cover gasket
Fits Dana Spicer 60, 70, 70U and 70HD

from

$274.99

Yukon replacement standard open carrier case for Dana 60, 4.56 & up (Not ABS) 2-7/16″ tall.

Product Features:

Standard open carrier case
Fits Dana Spicer 60
4.56 and up ratio only
Does not include spider gears
Not compatible with ABS applications

from

$51.99

Notched cross pin shaft for 12P and 12T GM. This cross pin shaft is not compatible with Powertrax Lock Rights or Spartan Lockers.

Product Features:

Cross pin shaft
Fits GM 12 bolt passenger car and truck
Notched
Not compatible with Spartan Lockers or Lock Rights

from

$10.99

Yukon 1541H alloy 5 lug rear axle (one single shaft) for ’99 – ’04 8.8″ Ford Mustang. axle has a length of 30-3/4″ inches and 31 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a five year warranty against manufacturing defects. This is a C-clip axle.

Product Features:

Fits 1999-2004 Ford Mustang
31 spline
30 3/4″ long
5 lug
Fits ABS applications
Does not include ABS tone ring

from

$809.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits Dana Spicer 44 with 30 spline axles
3.92 ratio and up only
4-spring, clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$7.79

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$67.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

Powr Lok button kit
Fits Dana Spicer 30, 44 and Chrysler 8.75″

from

$47.49

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$14.29

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National