1965 Pontiac GTO Performance Engines

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

Fel-Pro® Performance Gaskets deliver reliable sealing under grueling racing conditions.

Product Features:

• Blue Stripe® performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
• Not intended for use in emission controlled vehicles.

Designed to open at 160 degrees every time, regardless of engine rpm, and it’s high-flow design and brass and copper construction eliminate the damaging effects of cycling when you’re stuck in stop-and-go traffic. It includes the rubber gasket and has a pressure relief valve.

Product Features:

• Opens sooner than stock at 160 degrees
• High flow design for performance applications
• Includes rubber o-ring seal/gasket
• Incorporates pressure relief valve

Designed to open at 180 degrees every time, regardless of engine rpm, and it’s high-flow design and brass and copper construction eliminate the damaging effects of cycling when you’re stuck in stop-and-go traffic. It includes the rubber gasket and has a pressure relief valve.

Product Features:

• Opens sooner than stock at 180 degrees
• High flow design for performance applications
• Includes rubber o-ring seal/gasket
• Incorporates pressure relief valve

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.

Product Features:

• Good blend of efficiency and performance.
• Perfect choice for performance street rebuilds.
• Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched to Edelbrock Performer Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.

Product Features:

• (16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
• Shank O.D. .540″
• Includes Locks and Hex Wrench
• High-Quality Grade Steel
• Heat-Treated For Ex Strength
• Plated With Durable Gold Tone Finish

These are high quality nuts with allen set screws to provide you with that positive lock needed for Race or original equipment Rocker Arms.

Product Features:

• They Are Zinc Dichromate Plated Steel
• They Have Black Oxide Coated Set Screws
• Keeps Rocker Arms Positively Locked
• (16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
• Includes Locks and Hex Wrench
• Shank O.D. .603″

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Edelbrock part #3756 Performer Pontiac EGR intake manifold is designed for 1965-79 Pontiac 326-455 c.i.d. V8’s (except Ram Air V and 265/301 V8’s). Provides great throttle response for performance you can feel. Ideal for cars, 4x4s, tow vehicles, RVs and

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg. Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal if Correct Carburetor Used

Product Features:

• Idle-5500 RPM Range
• Dual Plane Type-4150 Style Flange
• 5.5 in. Front Height, 6.05 in. Center Height, 6.6 in. Rear Height
• Polished Finish
• Non-EGR

HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2400 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Product Features:

• Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
• Set of 16
• 1.50 in. Outside Diameter
• Steel Material
• Black Oxide Finish

Product Features:

• Cylinder Head Gasket
• 1961-1980 326-389-400-421-428-455

Product Features:

• Head: 4.300″ Bore/0.038″ Thick/8.96cc Vol.
• Intake: 1.18″x2.20″ Port/.060″ Thick
• Exhaust: 1.880″ Port
• 3/16″ Valve Cover
• Multi Piece Configuration

Edelbrock #8895 Water Pump GM gen III ls1 & gen iv ls engines insert style ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “supe

Product Features:

• Standard Impeller Rotation
• 0.750 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 6.00 in. Block To Hub Height
• Natural Finish

Edelbrock #88563 Water Pump Pontiac 389-455 standard rotation black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooli

Product Features:

• Standard Impeller Rotation
• 0.625 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 4.50 in. Block To Hub Height
• Black Finish

Product Features:

• For Professional Cylinder Head Porter
• 72cc Chamber Size
• As-Cast Casting Has Small Ports And Chambers
• Max Valve Size is 2.11 Int and 1.66 Exh
• 14-Degree Valve Angle
• Enough Wall Thickness For CNC Machining
• Seats and Manganese-Bronze Guides Included

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

• Complete with o-rings and mounting bolts
• Features an o-ring style seal to prevent water leaks
• Chrome plated
• 1/2″ NPT port can be used for various coolant temp related sensors or switches

Spectre’s Pontiac water neck fits 1967 – 1978 Pontiac V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts and sealing O-ring.

Product Features:

• Fits 1967 – 1978 Pontiac V8 engines
• Includes sealing O-ring and bolts
• Chrome plated
• Easy to install

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.