1964 Pontiac Catalina Differentials

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

21 Piece bearing race driver set. (Box wt: 140lbs) No return.

Product Features:

• Bearing race driver set
• 21 pieces
• All steel construction

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Yukon yoke for GM 7.5″ (mech 3R) in a triple lip design. 2.556″ snap ring span, 1.125″ cap diameter. Inside snap ring. This yoke uses inside clips. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits GM 7.5″ and 7.625″
• 27 spline
• Mechanics 3R u-joint size
• Inside snap ring design
• 2.556″ snap ring span
• 1.125″ cap diameter
• Strap style

Polished aluminum cover for 8.6″, 8.2″ and 8.5″ GM rear.

Product Features:

• Fits GM 8.5″ and 8.6″
• Finned polished aluminum

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects. This case is drilled for 3/8″ bolts. Some factory gears use 7/16″ bolts. If your factory gear uses 7/16″ bolts you will need to drill out the ring gear bolt holes.

Product Features:

• Fits GM 8.2″ in Buick, Oldsmobile and Pontiac
• 3.31 ratio and up only
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Product Features:

• KIT SHIM

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits 8.2″ Buick, Oldsmobile and Pontiac
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

Pinion nut for GM 12 bolt car & truck, 55-62 car & truck, 8.2″, 8.2″ Buick/Olds/Pontiac & 63-79 Corvette. 1 1/8″ socket, 7/8″ x 16 thread.

Product Features:

• Pinion nut for GM 12 bolt car and truck, 8.2″, 8.2″ Buick, Oldsmobile and Pontiac and 1963-1979 Corvette
• 7/8″ x 16 thread
• 1 1/8″ socket

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.2″ & 8.5″ differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits GM 7.5″, 7.625″ 8.2″ and 8.5″
• Includes carrier bearings and races and “super” carrier shim kit

Yukon standard open spider gear kit for 8.5″ GM with 28 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fits GM 8.5″ open differential with 28 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

Product Features:

• MINI INSTALL KIT GM 12BLT 8.875 CAR

8.5″ Oldsmobile crush sleeve. Approx 2.420″ long.

Product Features:

• Crush sleeve
• Fits 8.5″ Oldsmobile
• 2.420″ tall

Product Features:

• Shim kit
• Fits GM 7.5″ and 7.625″ with Eaton positraction

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

• Includes three quarts of Redline Shockproof oil

Yukon 1541H alloy rear axle for ’80-’88 8.5″ GM Caprice and Impala with a length of 30-7/16″ inches and 28 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a C-clip axle.

Product Features:

• 28 spline
• 30 7/16″ long
• Fits GM 8.5″ in 1980-1988 Caprice and Impala

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

Ring gear bolt for GM 7.5″, 7.6″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ & 8.6″ IRS. 7/16″ x 20.

Product Features:

• Ring gear bolt for GM 7.5″, 7.625″, 7.6″ IRS, 8.0″, 8.25″ IFS, 8.5″, 8.6″ and 8.6″ IRS
• 7/16″ x 20

8.5, 9.5, & 8.2 Buick, Oldsmobile, Pontiac GM REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

• Pinion Redi-sleeve
• Fits GM 8.5″, 9.5″ and 8.2″ Buick, Oldsmobile and Pontiac

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 8.2″ Buick, Oldsmobile and Pontiac
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

M802048 set-up bearing (one bearing). No return.

Product Features:

• Set up bearing
• Fits M802048 pinion bearing
• Easily slips on and off pinion journal to allow for easier pinion depth adjustment

Product Features:

• Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
• Interlocking design makes installation much easier

3/8″ ring gear bolt washer for GM 12 bolt car & truck, 8.2 BOP & more.

Product Features:

• Ring gear bolt washer for GM 12 bolt car and truck, 1955-1964 passenger car, 1963-1979 Corvette and 8.2″ Buick, Oldsmobile and Pontiac

Product Features:

• GM 10BL 7.5&7.625 R/P 3.23 MG 10 3/8 X 18 LH THRED BLTS, PD=1.438

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits GM 7.5″ and 7.6″
• 7.50″ ring gear diameter
• 27 spline pinion
• 10 ring gear bolts
• 3.73 ratio

Product Features:

• GM 10BL 8.5 R/P 3.42 MG FRT/REAR