1964 Ford Mustang Differentials

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

• Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit.

Product Features:

• .047″ thick cellulose/nitrile composite gasket material
• Precision die cut
• Reusable

Product Features:

• BOLT 9″ FORD OPEN R.G. SAME AS M-4216A200

O-ring for 9″ Ford.Yukon Mighty seal.

Product Features:

• Pinion support o-ring
• Fits Ford 9″

9″ Ford 2 piece solid preload pinion spacer, Daytona or standard.

Product Features:

• Crush sleeve eliminator kit for Ford 9″ with 28 spline pinion

Spartan spring & pin kit, fits smaller designs.

Product Features:

• Replacement spring and pin kit for Spartan Locker
• Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
• Includes 4 springs and 4 alignment pins

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9″ with Daytona pinion support
• Included are pinion bearings and races, pinion seal, crush sleeve eliminator , complete pinion shim kit, and marking compound with brush.

9.25 Chrysler FRONT PINION KIT , 03 & UP DODGE TRUCK .

Product Features:

• Pilot bearing
• Fits Ford 8″

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Ford 9″ with LM603011 carrier races
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, pilot bearing, thread locker, marking compound with brush and gasket.

Product Features:

• Friction plate
• Fits Ford 8″ and 9″ Trac Loc positraction

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Mini Spool 8″ and 9″ for Ford with 28 spline axles. Cross is bored for three cross pins. Mini spools are a low-cost traction option for vehicles looking for full-time lockup. The mini spool installs into a standard open carrier and give 100% power to both tires at all times. These units are not recommended for street-driven vehicles. We recommend full spools for vehicles with large tires or high horsepower. These units come with a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 9″ with 28 spline axles
• Installs into a standard open carrier case
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

• Fits Ford 8.8″ with 31 spline axles
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Pinion depth shim kit 9″ Ford.

Product Features:

• Pinion depth shims for Ford 9″

Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:

• Pinion nut for Ford 7.5″, 8″ and 9″
• 3/4″ x 20 thread
• 1 1/6″ socket

Differential Carrier

Pinion gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

• Pinion gear thrust washer
• Fits Ford 8.8″
• 0.750″ I.D.

Yukon standard open spider gear kit for 8.8″ Ford with 31 spline axles and 7/8″ pin. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fits Ford 8.8″ with 31 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
• 0.875″ cross pin shaft diameter

Product Features:

• Trac Loc spring for Ford 8.8″
• 31 spline applications only

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M86610 race
• All steel construction

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker uses 8620 internals and a patented design to provide maximum strength and reduce common failures. Assembled in the USA! This unit has been approved for competition in NASCAR National & Touring series. This is a race unit designed for extreme off road use or racing. All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

• Fits Ford 9″ with 35 spline axles and loadbolt housing
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA
• Aggressive design for racing applications only

Standard Open side gear thrust washer for 7.5″ Ford.

Product Features:

• Side gear thrust washer
• Fits Ford 7.5″

Yukon short yoke for Ford 9″ HD with 28 spline axles and a 1330 U/joint size. 4″ length. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 9″
• 28 spline
• 1330 u-joint size
• 3.625″ snap ring span
• 1.125″ cap diameter
• Outside snap ring design
• U-bolt style

Standard open cross pin shaft (.750″) for Ford 8″, 8.8″, 9″ and Model 20.

Product Features:

• Cross pin shaft for Ford 8″, 8.8″ and 9″ and AMC Model 20
• Fits standard open differentials only
• 0.750″ diameter

Product Features:

• FRD 9″ R&P 3:00 RATIO

Pinion support bolt for 8″ and 9″ Ford.

Product Features:

• Pinion support bolt for Ford 8″ and 9″
• 3/8″ x 24 thread
• 1.0″ long

Yukon standard open spider gear kit for 9″ Ford with 31 spline axles and 2-pinion design. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fits Ford 9″ open differential with 31 spline axles
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.