1964 Ford Custom Performance and Racing Products
Find Your Specific 1964 Ford Custom Performance and Racing Products
Below you will find various in-demand Ford Performance and Racing Products, components and accessories for your 1964 Custom. Advance Auto Parts has popular Custom parts like Performance Ignition Products, Performance Fuel Systems, Performance Engines and more. You’ll also find aftermarket and OEM Performance and Racing Products for other Custom model years including
1968,
1969,
1970,
1971,
1972,
1973,
1974,
1975,
1976 and more. Select a category of 1964 Ford Custom Performance and Racing Products below and start saving instantly.
Popular 1964 Ford Custom Performance and Racing Products Categories
Essential Performance and Racing Products for 1964 Ford Customs
Holley – Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny (Part No.0-80457S)
from
$509.99
Holley’s new 0-80457SA is constructed from aluminum which compared to its zinc counterpart equates to a weight savings of 40%! Holley’s aluminum 0-80457SA will hold its shine longer and also can be hand polished for a custom look! Its 600 CFM of airflow,
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
Edelbrock – Performer Series Retainer (Qty 16) (Part No.9724)
from
$106.99
Product Features:
See More
- Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
- Set of 16
- 1.50 in. Outside Diameter
- Steel Material
- Black Oxide Finish
MSD Ignition – Blaster 2 Coil: High Performance Ignition Upgrade (Part No.8202)
from
$55.99
If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.
Product Features:
See More
Product Features:
- Improved output coil for electronic ignitions
- Works w/Blaster Ignition Or MSD 5/6/7 Series
- Ballast Resistor Required If Used w/Stock Points Ignition
- Alkyd tower w/high dielectric properties lessens carbon tracking
B & M – Automatic Shifter, Magnum Grip Street Bandit (Part No.81050)
from
$799.99
The B&M Racing Street Bandit Pistol-grip shifter is perfect for the person looking for a gated performance shifter in a compact good looking package which can be mounted in door cars. The Street Bandit features replaceable 2, 3 or 4 speed forward pattern gate plates along with a 3 speed reverse pattern gate plate, all guaranteeing you won’t miss a shift. Other features include a back-up light switch, neutral safety switch, brushed aluminum cover, CNC aluminum Magnum Grip shift handle, a 5ft Super Duty cable, all brackets, levers and instructions for an easy installation. Be sure to check out all our optional side grip plates including real Rosewood engraved with the B&M logo part #81086, CNC billet aluminum side plates with 12 volt micro-switch #81060, 81063, 81078 and coming soon optional colored side plates to customize the look of the shifter. Also see optional floor mounting bracket #80884
Product Features:
See More
Product Features:
- Ideal For High-Tech Pro-Street
- Ideal For High-Tech Street Rods
- Narrow Styled Aluminum Housing
- Includes Neutral Safety Switch
- Includes Backup Light Switch
- Includes Billet Aluminum Knob
- Can Be Used w/Reverse Pattern Valve Body
Competition Cams – Valve Seals, Umbrella 11/32" 1 St (Part No.502-16)
from
$230.99
COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.
Product Features:
See More
Product Features:
- Work with stock guides and 11/32″ valve stem diameter
- Valve stem oil seals keep unwanted oil from entering the combustion chamber
- Several different types of valve seals are offered
Edelbrock – Performer RPM Series fuel pump is for 289-351W Ford (Part No.1725)
from
$186.99
Product Features:
See More
- Mechanical Operation
- Fuel Sending Unit Not Included
- For Small-Block 289-351 Ford Engines
- In Tank Mounting Type
- 110 GPH
Competition Cams – ROCKER ARMS, DIE CAST ALUM SMALL BLOCK FORD 1.6 1 ST (Part No.17043-16)
from
$249.99
The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.
Product Features:
See More
Product Features:
- Cost effective aluminum construction provides superior strength to weight ratio
- Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
- Durable design increases valve lift while withstanding the rigors of moderate race use
- Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.
MSD Ignition – Distributor Gear; Steel; Ford 351C; 460 (Part No.85813)
from
$158.99
A distributor’s performance is only as good as its drive gear. MSD ignition has put a great deal of effort into researching and testing a variety of metallurgical compositions, heat treating and coatings to provide you with a durable, accurate and strong distributor gear. The result is a special iron alloy gear that is treated to a low-friction coating process. To you this means long life, an easy break-in period and reliable performance. Features micro polished surface for smooth contact. Proprietary formulated ductile iron. Melonite QPQ coated reduces friction and initial wear. Interstitial carbide concentration improves wear resistance and running properties.
Product Features:
See More
Product Features:
- Increased outer hardened layer thickness (RC 55-60)
- Micro Polished Surface For Smooth Contact
- Proprietary formulated ductile iron.
- Melonite QPQ coated reduces friction and initial wear
- Interstitial carbide improves wear resistance/running properties
Edelbrock – Torker-Plus Camshaft Kit for 1957-95 Small-Block Ford 289-302 V8 (Part No.5022)
from
$440.99
Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.
Product Features:
See More
Product Features:
- Designed for 2500 to 6500 Performance
- Designed for Hi-Perf Street; Drag or Marine Use
- Matched to Edelbrock Torker II Intakes
- Includes Hydraulic Lifters and Assembly Lube
- Dyno Matched/Street Proven Performance
- Take The Guesswork Out Of Camshaft Selection
Mr. Gasket – Intake Manifold Bolts (Part No.958G)
from
$23.79
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 5/16 inch-18 x 2 inch bolts & washers
Product Features:
See More
Product Features:
- Hex Head
- Zinc Plated
- Ideal For Minimal Space
- 12-Point Head And Flange
- Zinc Plated For Protection
Mr. Gasket – Thermocap Radiator Cap (Part No.2471S)
from
$53.99
Knowing your coolant temperature can help to prevent burn injuries. Thermocap Cap, with its built-in calibrated thermometer, indicates the coolant temperature. This is useful information prior to cap removal. Never attempt to remove Thermocap Cap when the coolant temperature is very hot. The escaping hot coolant and steam may burn you. Reclamation valve works great with your coolant recovery system. Your radiator can reclaim coolant from your overflow bottle. Wide 30 degree to 270 degree F temperature range. Calibrated in centigrade and Fahrenheit. Color-coded temperature ranges.
Product Features:
See More
Product Features:
- Indicates Coolant Temperature
- Helps to Prevent Injuries from coolant or steam burns
- Integrated Coolant Reclamation Valve
- Improves Underhood Appearance
- Fahrenheit and centigrade readings
- Various valve pressures available
Mr. Gasket – Ultra Seal: Harmonic Balancer Bolt/Washer Kit (Part No.7847)
from
$45.49
Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.
Product Features:
See More
Product Features:
- Heat treated black oxide coated Grade 8 alloy steel
- Thick parallel ground washer provides more accurate, uniform torque
- Hex Prevents Socket Slippage
- Accurate And Uniform Torque
- Black Plated Finish
Edelbrock – Pushrod Set for Ford 351M/400 (Part No.9633)
from
$198.99
Product Features:
See More
- 9.5 in. Length
- 0.312 in. Diameter
- 4130 Chromoly Steel Material
- Black Oxide Finish
- Made In The USA
Mallory – Distributor Wiring Harness (Part No.29349)
Edelbrock – Valve Cover Gasket Set for Ford (Part No.7563)
Edelbrock – RPM Air-Gap Dual-Quad Small Block Ford 351W Intake Manifold (Part No.7585)
from
$595.99
Air gap cooler and denser mixture for more power. Street and high performance compatible. Available in cast, polished and endurashine finish.
Product Features:
See More
Product Features:
- Based on C26 Low Profile with Unique Air Gap
- Air Gap Cooler and Denser Mixture for More Power
- 1.625 in. Taller Than Low-Profile PN[5425]
- Also Available In EnduraShine Finish PN[75254]
- Also Available As Complete Kit PN[2025/20254]
- Best When Matched with Edelbrock 500cfm Carburetor
- Use Fuel Line Kit PN[8088/8091]
- Use Progressive Throttle Linkage Kit PN[7094]
Accel – Contact Set Hp 32 Oz (Part No.110228)
from
$53.99
Heavy duty points sets are quipped with extra think contack arms to prevent flexing at high RPMS. Large radiused tungsten contants provide crisp circuit breaking for peak coil output. High strength phenolic rubbing blocks provide superior durability when used with heavy duty spring tension.
Product Features:
See More
Product Features:
- Extra Thick Contact Arms
- Large Radius Tungsten Contacts
- High Strength Phenolic Rubbing Blocks
- Prevents Points Float
- Moisture-Proof Buna-N Condenser
Competition Cams – High Energy/Marine 218/218 Hydraulic Flat Cam (Part No.31-218-2)
from
$403.99
HYDRAULIC – High Energy: Good for daily driven performance vehicles. Mid-range power. Slightly lower gears. Mild rough idle. OR Marine: Single or dual engines. Best for inboard/outboard. Noticeable idle.
Product Features:
See More
Product Features:
- HYDRAULIC – High Energy: Good for daily driven performance vehicles. Mid-range power. Slightly lower gears. Mild rough idle. OR Marine: Single or dual engines. Best for inboard/outboard. Noticeable idle.
- 268/268 Advertised Duration, 218/218 Duration @ .050″, .456″/.456″ Lift, 110 Lobe Separation
- 289-302 Firing Order
Mr. Gasket – Valve Cover (Part No.9413)
from
$101.99
These Mr. Gasket chrome plated stamped steel valve covers have a flat smooth top, and internal baffles. 7-bolt design. Sold as a pair.
Product Features:
See More
Product Features:
- Chrome plated steel construction
- Sold as a pair
- Fits Ford big block (385 series)
- Long Lasting Durability
- Cadmium Plated To Resist Corrosion
- Easy Installation
Mr. Gasket – Dust Cap (Part No.2485)
from
$14.29
If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.
Product Features:
See More
Product Features:
- Chrome Plated Steel
- Set of 2 Caps
- Easy Installation
- 2 Per Set
Competition Cams – Xtreme Energy 218/224 Hydraulic Roller Cam and Lifter Kit (Part No.CL34-422-9)
from
$1245.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.
Product Features:
See More
Product Features:
- Excellent performance in street carbureted applications.
- More vacuum allows an increase in duration for improved performance and assists power brakes.
- Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
- Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
MSD Ignition – Distributor; Ford 351W; Ready-to-Run (Part No.8354)
from
$635.99
MSD’s Ready-to-Run Ford distributors are the perfect upgrade for bulky Duraspark systems or ancient breaker point models. All you need to do is drop it in the engine, connect three wires and fire the engine. Each distributor features an ignition module that produces a powerful inductive spark to improve combustion of the fuel mixture resulting in quick starts, smooth idle and increased performance. The billet aluminum housings of these distributors are 5/8 In. smaller in diameter to accommodate induction setups and tight engine compartments. A maintenance-free magnetic pick-up is responsible for triggering the high voltage sparks while a sealed ball bearing guides an oversized shaft. Beneath the bolt down cap and MSD race rotor you’ll find MSD’s accurate mechanical advance assembly. Different advance springs and stop bushings are supplied so you can easily tune a curve to match your needs. Plus, there is a vacuum advance canister to increase economy on long drives.
Product Features:
See More
Product Features:
- Now includes built-in Rev Limiter
- Built-in module produces a 7.5 amp single spark through high rpm
- Vacuum advance canister for improved economy (can be locked out)
- CNC machined billet aluminum housing and billet aluminum base
- Housing Is 5/8 in. Smaller In Diameter Than Stock Ford Distr.
- Maintenance-free magnetic pickup and precision reluctor
- Creates stable trigger signals throughout the rpm range
- QPQ coated polished steel shaft; guided by sealed ball bearings
- Advance plate and weights are fine blanked from chrome moly steel
- Mech. advance assem. can be locked out for crank trigger systems
- Advance weight pins are staked and tig welded to the plate
- Nylon pads ensure smooth operation of the advance weights
Hays – Flywheels (Part No.12-060)
from
$199.99
Flywheels
Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7808)
from
$85.99Product Features:
- Solid Bushing Chain Resists Stretching
- For Use with Stock or Edelbrock Camshafts
- Stressproof Steel Crank Gears
- 3 Keyway Setting Points To Ensure Accurate Timing
- True Bearing Surface Rolls with the Sprockets
Accel – Kit:Ford V8Sngl Pnt Eliminator (Part No.2020)
from
$113.99
Put and end to high maintenance point ignition systes by utilizing a specialized electronic circuitry and infrared signal. Stabalizes ignition timing from 1 to 10,000 RPM. Improves performance and fuel efficiency, easy to install with hand tools, reduces maintenance. It is built with the latest thermal clad based surface mount construction for maximum dependability and long life.
Product Features:
See More
Product Features:
- Put And End To High Maintenance Point Ignitions
- Specialized Electronic Circuitry
- Stabalizes Ignition Timing From 1 To 10000 RPM
- Improves Performance And Fuel Efficiency
- Easy To Install With Hand Tools
- Thermal Clad Based Surface Mount Construction
- Utilizes Specialized Electronic Circuitry
- Ignition Timing Is Stable From 1 To 10000rpm
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1416)
from
$39.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Copper Seal: Exhaust Gasket Set (Part No.7160)
from
$71.99
Mr. Gasket CopperSEAL Header Gaskets are a high quality copper gasket that performs extremely well and are reusable. We recommend this in all racing and high performance applications. They are for stock heads unless indicated, and work well in high heat and turbocharged applications.
Product Features:
See More
Product Features:
- Manufactured from ¿Dead Soft¿ (solid) .043″ thick copper material
- Manufactured from ┐Dead Soft┐ (solid) .043″ thick copper material
- .051″ embossment around each exhaust port to seal irregular surfaces. Total gasket thickness .094″
- Provides excellent sealing and durability
- Conforms to and seals minor surface irregularities
- For high performance street, drag race, oval track and turbocharged (extreme heat) applications
Mr. Gasket – Aluminum Exhaust Gasket (Part No.7410G)
from
$43.99
Upgrade to Mr. Gasket Aluminum Layered Header Gaskets and eliminate blown exhaust gaskets forever. They conform to warped and damaged surfaces to create an airtight, leak-proof seal and will not shrink or deteriorate EVER.
Product Features:
See More
Product Features:
- Reusable header, exhaust manifold and collector flange gaskets
- Manufactured from “dead soft” aluminum layers – .125″ thick
- Conforms easily to surface irregularities (warped flanges)
- Compresses down to 0.060″ to create a tight leak-proof seal
- Will not shrink, deteriorate, or blow out- eliminating gasket leaks
- For high performance street, drag race and oval track use
Upgrade your 1964 Ford Custom with Top-Quality Performance and Racing Products
When it comes to maintaining or upgrading your 1964 Ford Custom, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Performance and Racing Products are key to keeping your Custom functioning at its best. At Advance Auto Parts, we offer a wide selection of 101 Performance and Racing Products for the 1964 Ford Custom, designed to meet your needs without breaking the bank.
From
Performance Ignition Product
replacements to
Performance Fuel Systems
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1964 Ford Custom at great prices.
Our Performance and Racing Products inventory for this model
ranges from just $8.99 to $819.99, with
an average price of $234.41.
Our 101 Performance and Racing Products in stock come from 11 trusted brands, so you’re sure to find the right part for your 1964 Ford Custom without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1964 Ford Custom, we stock popular OEM and aftermarket Performance and Racing Products from top names
like Edelbrock, FEL-PRO Performance, Holley, and more.
Edelbrock Performance and Racing Products
start at just $186.99 and boast an impressive 4.4 stars average rating from customers.
FEL-PRO Performance and Holley also bring quality to the table, with Performance and Racing Products available starting at $35.99, and at an average 4.2 stars rating.
With 626 customer reviews and counting, our 1964 Ford Custom Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Fluids and Chemicals
and more to make sure your 1964 Ford Custom is always ready to roll. We’re committed to providing you with everything you need to keep your Custom in top shape, all in one place.
Start shopping confidently below for your 1964 Ford Custom!
Best-Selling Performance Ignition Products for 1964 Ford Customs
Enhance the driving experience in your Ford with 7 quality Performance Ignition Product components, starting at $34.49.
Mallory – Unilite Ignition Module (Part No.605)
from
$95.99
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
Accel – Contact And Condenser Kit (Part No.8203)
from
$89.99
Regain horsepower and economy for your street machine with new contact and condenser kit. Large tungsten contacts provide crisp coil firing and perform solidly up to 5,000 RPM. Condenser’s special winding protects from pitting of point contacts. Heavy duty 23 ounce points.
Product Features:
See More
Product Features:
- High Performance Points and Condenser
- With Integral Conductor
MSD Ignition – Blaster 2 Coil: High Performance Ignition Upgrade (Part No.8202)
from
$55.99
If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.
Product Features:
See More
Product Features:
- Improved output coil for electronic ignitions
- Works w/Blaster Ignition Or MSD 5/6/7 Series
- Ballast Resistor Required If Used w/Stock Points Ignition
- Alkyd tower w/high dielectric properties lessens carbon tracking
Accel – Kit:Ford V8Sngl Pnt Eliminator (Part No.2020)
from
$113.99
Put and end to high maintenance point ignition systes by utilizing a specialized electronic circuitry and infrared signal. Stabalizes ignition timing from 1 to 10,000 RPM. Improves performance and fuel efficiency, easy to install with hand tools, reduces maintenance. It is built with the latest thermal clad based surface mount construction for maximum dependability and long life.
Product Features:
See More
Product Features:
- Put And End To High Maintenance Point Ignitions
- Specialized Electronic Circuitry
- Stabalizes Ignition Timing From 1 To 10000 RPM
- Improves Performance And Fuel Efficiency
- Easy To Install With Hand Tools
- Thermal Clad Based Surface Mount Construction
- Utilizes Specialized Electronic Circuitry
- Ignition Timing Is Stable From 1 To 10000rpm
Mallory – Distributor Wiring Harness (Part No.29349)
Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)
from
$204.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).
Product Features:
See More
Product Features:
- Glass Filled Polyester Case
- Longer Spark Duration
- Increased Performance
- No Energy Loss Due To Arcing
- Includes Brass Contact Terminal
Accel – Contact Set Hp 32 Oz (Part No.110228)
from
$53.99
Heavy duty points sets are quipped with extra think contack arms to prevent flexing at high RPMS. Large radiused tungsten contants provide crisp circuit breaking for peak coil output. High strength phenolic rubbing blocks provide superior durability when used with heavy duty spring tension.
Product Features:
See More
Product Features:
- Extra Thick Contact Arms
- Large Radius Tungsten Contacts
- High Strength Phenolic Rubbing Blocks
- Prevents Points Float
- Moisture-Proof Buna-N Condenser
Most Popular 1964 Ford Custom Performance Fuel Systems
Customize your Ford with 8 Performance Fuel Systems products
like Performance Fuel Pumps and
Performance Carburetors, all
priced under $819.99.
Holley – Street Carburetor: 600 CFM, Electric Choke, 4 Barrel, Square Bore, Single Inlet, Shiny (Part No.0-80457S)
from
$509.99
Holley’s new 0-80457SA is constructed from aluminum which compared to its zinc counterpart equates to a weight savings of 40%! Holley’s aluminum 0-80457SA will hold its shine longer and also can be hand polished for a custom look! Its 600 CFM of airflow,
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)
from
$394.99
The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Manual Choke
- 4 Barrel Count
- Square Bore
- Smooth Secondary Transition
- Both Timed and Full Vacuum Ports
- Includes PCV Outlet
Holley – Prem Street Carbs (Avengers) (Part No.0-80770)
from
$716.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Edelbrock – Performer RPM Series fuel pump is for 289-351W Ford (Part No.1725)
from
$186.99
Product Features:
See More
- Mechanical Operation
- Fuel Sending Unit Not Included
- For Small-Block 289-351 Ford Engines
- In Tank Mounting Type
- 110 GPH
Holley – Street Carburetor: 670 CFM, Electric Choke, 4 Barrel, Square Bore, Dual Inlet, Shiny (Part No.0-80670)
from
$699.99
Square flange bolt pattern. Performance calibrated. The ultimate vacuum secondary street performance upgrade.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Street Calibration That Works Out Of The Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- No Unnecessary Trips Back To The Parts Store
- Limited Lifetime Warranty
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Edelbrock – Performer Remanufactured Carburetor, 600 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.9905)
from
$437.99
The Edelbrock 9905 Remanufactured Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 9905 Remanufactured Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.
See More
Holley – Off Road Carbs (Part No.0-90670)
from
$819.99
The off-road truck avenger is designed specifically for off-road applications. The unique fuel metering block eliminates fuel spillover through the boosters at extreme angles allowing for 40 degree climbing, 30 degree side hill maneuvers and nose-down descents to avoid hesitations, stalling and flooding typically associated with carbs in an off road environment. The 470 CFM off-road truck avenger is the perfect carburetor for 4 cylinder, V-6, and inline 6 cylinder engines. Viton(R) is a registered trademark of DuPont Performance Elastomers.
Product Features:
See More
Product Features:
- Gold Dichromate Finish For Extreme Off Road Environments
- Single Feed Fuel Inlet For Ease Of Installation
- Optimized Off-Road Calibration That Works Out-Of-The-Box
- Factory Preset Electric Choke For Easy Startups
- Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
- One Piece Off-Road Vent Tube Eliminates Fuel Spillover
- Metering Block For Flood Free Op. 40 deg. Climb/30 deg. Side Hill
- Limited Lifetime Warranty Defects In Material/Workmanship
Edelbrock – Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.9907)
from
$407.99
Product Features:
See More
- Satin Finish
- 4 Barrel
- Annular Booster Type
- Manual Choke Type
- 750 cfm Maximum Flow Rating
Top Picks for 1964 Ford Custom Performance Engines
Upgrade Ford Customs with top-quality Performance Engines parts, including 65 OEM and aftermarket selections for your 1964 model.
FEL-PRO Performance – Lower Intake Manifold Gasket Set: 11 Piece Set (Part No.1250)
from
$35.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1684)
from
$50.99
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Rigid core, molded silicone rubber gaskets provide for ease of installation, and are great for on-again/off-again situations (like setting valve lash).
- Features high-tech silicone material for long life, a solid steel core for strength and durability, and stainless steel compression limiters to prevent
- Not intended for use in emission controlled vehicles.
Competition Cams – VALVE SEALS, TEFLON 3/8" 1 ST (Part No.505-16)
from
$33.99
COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.
Product Features:
See More
Product Features:
- Work with .530″ guides and 3/8″ valve stem diameter
- Valve stem oil seals keep unwanted oil from entering the combustion chamber
- Several different types of valve seals are offered
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-1)
from
$52.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
- NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
- SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
- STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
- DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
Mr. Gasket – Ultra Seal: Valve Cover Gasket Set (Part No.5870)
from
$42.99
Ultra-Seal is Mr. Gasket premium valve cover gasket material. It’s manufactured from a high density cork and rubber blend with a black latex coat applied to the outside to help seal minor flange irregularites and eliminate oil leakage. It creates a positive seal by controlled swelling of the gasket material when exposed to hot oil. For original equipment replacement, high performance street, drag race and oval track use. Sold as a pair. These gaskets are .187 inch thick.
Product Features:
See More
Product Features:
- Manufactured from high-density cork /rubber blend gasket material
- A black latex rubber coating is applied to outside of gasket to help seal minor flange irregularities and eliminate the possibility of oil leakage
- Creates a positive seal by controlled swelling of the gasket material when exposed to hot engine oil
- For OE replacement, high performance street, drag race and oval track
- .187″ thick
- Handles Ex Flange Pressure
- Forms Leak Proof Seal
- Black Latex Coating
Edelbrock – Performer 390 Intake Manifold for Ford FE, Satin Finish (Part No.2105)
from
$597.99Product Features:
- For Idle to 5500 RPM Street-Driven Performance
- Dual-Plane Low-Rise Intake w/180 deg. Firing Order
- Patented Runner Design Ensures Broad Torque Curve
- Excellent Throttle Response and Mid-Range Power
- 50-State Street Legal if Correct Carburetor Used
Mr. Gasket – Intake Manifold Bolts (Part No.958G)
from
$23.79
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 5/16 inch-18 x 2 inch bolts & washers
Product Features:
See More
Product Features:
- Hex Head
- Zinc Plated
- Ideal For Minimal Space
- 12-Point Head And Flange
- Zinc Plated For Protection
FEL-PRO Performance – Performance Cylinder Head Gasket (Part No.1020)
from
$39.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.
Product Features:
See More
Product Features:
- Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
- Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
- Raises combustion sealing force to roughly three times that of standard head gaskets.
- Steel wire rings for the greatest combustion seal strength.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Ultra Seal: Harmonic Balancer Bolt/Washer Kit (Part No.7847)
from
$45.49
Mr. Gasket Harmonic Balancer Bolt for Ford V8 except 351C. Fits 221,260,289,302,351W small block Windsor engines, 332,352,360,390,406,410,427,428 FEs, and 429,460 385 series big blocks. 5/8-18 x 2 inch long heat treated black oxide coated Grade 8 alloy steel with a thick parallel ground washer to provide accurate, uniform torque.
Product Features:
See More
Product Features:
- Heat treated black oxide coated Grade 8 alloy steel
- Thick parallel ground washer provides more accurate, uniform torque
- Hex Prevents Socket Slippage
- Accurate And Uniform Torque
- Black Plated Finish
Mr. Gasket – Valve Cover Gasket Set (Part No.276)
from
$35.99
Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.
Product Features:
See More
Product Features:
- Manufactured from high-density cork/rubber blend gasket material
- Provides excellent sealing and durability
- For OE replacement, high performance street, drag race and oval track use
Edelbrock – Performer RPM Ford Small Block 302 Intake Manifold (Part No.7121)
from
$359.99Product Features:
- Best for the Ultimate in Street High-Performance
- Designed for 1500 to 6500 RPM Street-Driven Power
- Dual-Plane High-Rise Intake w/180 deg Firing Order
- Produces Incredible Top-End Horsepower
- Retains Good Throttle Response and Acceleration
- Larger Plenum and Runners Maximizes Other Upgrades
Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7808)
from
$85.99Product Features:
- Solid Bushing Chain Resists Stretching
- For Use with Stock or Edelbrock Camshafts
- Stressproof Steel Crank Gears
- 3 Keyway Setting Points To Ensure Accurate Timing
- True Bearing Surface Rolls with the Sprockets
FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1614)
from
$24.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Die cut silicone rubber gaskets conform to out-of-flat covers
- Great for on-again/off-again situations
- Not intended for use in emission controlled vehicles.
Competition Cams – VALVE SEALS, 11/32" TEFLON 1 ST (Part No.503-16)
from
$223.99
COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.
Product Features:
See More
Product Features:
- Work with .530″ guides and 11/32″ valve stem diameter
- Valve stem oil seals keep unwanted oil from entering the combustion chamber
- Several different types of valve seals are offered
FEL-PRO Performance – Lower Intake Manifold Gasket Set: 5 Piece Set (Part No.1246)
from
$39.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fel-Pro performance intake manifold gaskets have been tested with virtually all aftermarket cylinder head and intake manifold combinations.
- Performance intake manifold gaskets designed without a metal core, to allow engine builders to trim the gasket for exact fit on modified ports.
- Standard and Low riser
- Printoseal elastomeric sealing beads to provide extra sealing strength around the intake port.
- Not intended for use in emission controlled vehicles.
Edelbrock – Intake Manifold Gasket for 1985-1976 390-428 FE Fords (Part No.7224)
from
$30.99
Product Features:
See More
- Clean Positive Seal
- Embossed Silicone Bead Surrounding The Port
- Matched To Manifolds And Cylinder Heads
Mr. Gasket – Intake Gasket (Part No.203G)
from
$42.99
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. Complete with manifold end seals and distributor gasket (where applicable). For original equipment replacement, high performance street, drag race and oval track.
Product Features:
See More
Product Features:
- Manufactured from cellulose/nitrile composition gasket material
- Provides excellent sealing and durability
- Can be trimmed if necessary for modified port applications
- Complete with manifold end seals and distributor gasket where applicable
- For OE replacement, high performance street, drag race and oval track use
Edelbrock – Performer-Plus Camshaft Kit for Small-Block Ford 289-302 V8 (Part No.2122)
from
$338.99Product Features:
- Designed for Optimum Torque and Acceleration
- Maximum Performance From Idle through Mid-Range
- Matched to Edelbrock Performer Intakes
- Includes Hydraulic Lifters and Assembly Lube
- Major Improvement in Throttle Response and Torque
- Use For Daily Drivers/Trucks/Vans/RVs/4x4s
- Take The Guesswork Out Of Camshaft Selection
Competition Cams – Thumpr 226/241 Hydraulic Flat Cam (Part No.33-600-5)
from
$341.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.
Product Features:
See More
Product Features:
- Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
- Best with aftermarket converters and more rear gear.
- Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
Competition Cams – High Energy 206/206 Hydraulic Flat Cam and Lifter Kit (Part No.CL33-221-3)
from
$648.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.
Product Features:
See More
Product Features:
- Good blend of efficiency and performance.
- Perfect choice for performance street rebuilds.
- Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
Competition Cams – High Energy 218/218 Hydraulic Flat Cam and Lifter Kit (Part No.CL33-224-3)
from
$648.99
FE FORD HYDRAULIC CAM AND LIFTER KIT – High Energy: Good upgrade for factory performance cams in 390-428. Noticeable idle.
Product Features:
See More
Product Features:
- Cam and lifter kit for FE Ford engines
- CL-Kit includes cam, lifters, assembly lube, instructions and decals
- HYDRAULIC – High Energy: Good upgrade for factory performance cams in 390-428. Noticeable idle.
- 268/268 Advertised Duration, 218/218 Duration @ .050″, .494″/.494″ Lift, 110 Lobe Separation
Competition Cams – 10 Degree Superlock Steel Retainer Set of 100 for 1.500"-1.550" OD Valve Spring (Part No.741-100)
from
$637.99
10 Degree Superlock Steel Retainer Set of 100 for 1.500"-1.550" OD Valve Spring
Competition Cams – Magnum 248/248 Solid Flat Cam and Lifter Kit for Ford 352-428 (Part No.CL33-246-4)
from
$612.99
Magnum 248/248 Solid Flat Cam and Lifter Kit for Ford 352-428
Competition Cams – Magnum 236/236 Solid Flat Cam and Lifter Kit for Ford 352-428 (Part No.CL33-245-4)
from
$576.99
Magnum 236/236 Solid Flat Cam and Lifter Kit for Ford 352-428
In-Demand Performance Exhaust Products for 1964 Ford Customs
Select from 4 premium Performance Exhaust Products parts for your 1964 Ford Custom, with prices ranging from $26.99 to $71.99.
Mr. Gasket – Copper Seal: Exhaust Gasket Set (Part No.7160)
from
$71.99
Mr. Gasket CopperSEAL Header Gaskets are a high quality copper gasket that performs extremely well and are reusable. We recommend this in all racing and high performance applications. They are for stock heads unless indicated, and work well in high heat and turbocharged applications.
Product Features:
See More
Product Features:
- Manufactured from ¿Dead Soft¿ (solid) .043″ thick copper material
- Manufactured from ┐Dead Soft┐ (solid) .043″ thick copper material
- .051″ embossment around each exhaust port to seal irregular surfaces. Total gasket thickness .094″
- Provides excellent sealing and durability
- Conforms to and seals minor surface irregularities
- For high performance street, drag race, oval track and turbocharged (extreme heat) applications
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1467)
from
$45.99
Product Features:
See More
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1442)
from
$33.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Exhaust Gasket Set (Part No.251)
from
$26.99
Manufactured from high-temperature composite exhaust material. Provides maximum torque retention to eliminate gasket failure. Can be trimmed if necessary for modified port applications. Precision die cut for an excellent fit. For OE replacement, high-performance street, drag race and oval track.
Product Features:
See More
Product Features:
- Manufactured from high-temperature acrylic blend exhaust material
- Provides excellent sealing and durability
- Can be trimmed if necessary for modified port applications
- For OE replacement, high performance street, drag race and oval track use
- Precision Die Cut For Excellent Fit
Most Sold 1964 Ford Custom Performance Distributors
Explore our best-selling Ford parts for the 1964 Custom among 6 OEM and aftermarket options starting from $11.99.
PerTronix – D700700 Advance Spring Kit Flame-Thrower Billet Distributor (Part No.D700700)
from
$22.99
Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.
Product Features:
See More
Product Features:
- Performance mechanical advance springs.
PerTronix – D660701 Rotor Flame-Thrower Billet Distributor (Part No.D660701)
from
$19.99
Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.
Product Features:
See More
Product Features:
- Rotor for Flame-Thrower cast distributors
- Replacement premium rotor with brass contact.
PerTronix – D4061 Flame-Thrower HEI Distributor Rotor Red (Part No.D4061)
from
$17.99
Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.
Product Features:
See More
Product Features:
- Made from hi-performance 60 KV rated alkyd molding compound.
- Cap and rotor kits include nylon rotor hold-down screws.
- Flame-Thrower dust covers provide a larger air gap around the coil.
MSD Ignition – Distributor; Ford 289/302; Vacuum Advance (Part No.8479)
from
$562.99
The street pro-billet distributors are the perfect choice for powerful engines that see plenty of street time. The street models share the same features as the small diameter models shown above, plus feature a vacuum advance. This canister provides improved economy and an accurate mechanical advance lets you dial-in an advance curve to match your driving needs. A magnetic pick-up produces accurate trigger signals that remain stable throughout the entire rpm range of your engine and is completely maintenance-free.
Product Features:
See More
Product Features:
- Billet housing 5/8 in. smaller dia. than stock Ford distributors
- CARB E.O. Approved
- Easy-to-adjust mech. advance w/supplied springs and stop bushings
- Vacuum advance canister for improved economy (can be locked out)
- CNC machined billet aluminum housing and billet aluminum base
- Maintenance-free magnetic pickup and precision reluctor
- Creates stable trigger signals throughout the rpm range
- QPQ coated polished steel shaft; guided by sealed ball bearings
- Advance plate and weights are fine blanked from chrome moly steel
- QPQ coated for friction reduction
- Mech. advance assem. can be locked out for crank trigger systems
- Advance weight pins are staked and tig welded to the plate
PerTronix – D4062 Flame-Thrower HEI Distributor Rotor Blue (Part No.D4062)
from
$17.99
Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.
Product Features:
See More
Product Features:
- Made from hi-performance 60 KV rated alkyd molding compound.
- Cap and rotor kits include nylon rotor hold-down screws.
- Flame-Thrower dust covers provide a larger air gap around the coil.
PerTronix – D4260 Flame-Thrower Distributor Rotor HEI/EST Black (Part No.D4260)
from
$11.99
Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.
Product Features:
See More
Product Features:
- Made from hi-performance 60 KV rated alkyd molding compound.
- Cap and rotor kits include nylon rotor hold-down screws.
- Flame-Thrower dust covers provide a larger air gap around the coil.
Top-Rated Performance and Racing Products Brands For Your 1964 Ford Custom
Shop for the best-rated brands offering Performance and Racing Products and other products for your 1964 Ford Customs. Below you’ll find some of our best rated Performance and Racing Products from Edelbrock, FEL-PRO Performance, and Holley, and more. Performance and Racing Products from these brands that fit a 1964 Custom start at just $35.99 and are rated as high as 4.4 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.
Popular Edelbrock 1964 Ford Custom Performance and Racing Products
When it comes to maintaining or upgrading your 1964 Ford Custom, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Edelbrock ticks all of those boxes. We offer a wide selection of Edelbrock Performance and Racing Products, specifically designed for the 1964 Ford Custom. With over 3 Edelbrock brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $186.99, with an average price of just $393.32. Plus, with over 14 customer reviews and an average rating of 4.4 stars, you can trust that our Edelbrock Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
from
$186.99
(3)
Performer RPM Series fuel pump is for 289-351W Ford
“I installed this product on my ’57 Ford F100 that has a ’74 302 v8 under the hood. I geat great fuel pressure now, and this pump is a direct match fo”
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“i have delt with every auto parts dealer there is and advance allways treats me like im their only custemer, thanks guys and gals!!!”
from
$597.99
(1)
Performer 390 Intake Manifold for Ford FE, Satin Finish
“lightweight-runs great…took 80lbs off my engine”
Popular FEL-PRO Performance 1964 Ford Custom Performance and Racing Products
FEL-PRO Performance auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1964 Ford Custom owner should feel confident when installing genuine FEL-PRO Performance parts in their vehicle. To ensure the best fit and performance for your 1964 Custom, Advance Auto Parts carries a full inventory of 3 FEL-PRO Performance Performance and Racing Products. Plus you will be keeping your Ford in peak condition while saving money because prices on these FEL-PRO Performance Performance and Racing Products range from $35.99 to $52.99, plus, with more than 7 customer reviews and an impressive 4.2 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.
from
$52.99
(2)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
“cometic head gasket is great but prob is dose not seal if the block isn’t mirror finished. many people switch over to felpro and it has worked out gre”
FAQs for 1964 Ford Custom Performance and Racing Products
Which Performance and Racing Products are best-sellers for 1964 Ford Customs?
Out of 101 Performance and Racing Products that fit 1964 Ford Customs, the following parts are the top sellers:
- Lower Intake Manifold Gasket Set: 11 Piece Set (5991277) – $35.99
- Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (5020654) – $394.99
- Intake Manifold Bolts (17360287) – $23.79
What’s the price range for 1964 Ford Custom Performance and Racing Products?
Performance and Racing Product prices for the 1964 Ford Custom start at $8.99 and go up to $819.99 for the most premium parts.
What’s the average price of a Performance and Racing Product for a 1964 Ford Custom?
The average price for Performance and Racing Products for the 1964 Ford Custom is $234.41. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Performance and Racing Products for other Ford Custom model years?
What are the cheapest Performance and Racing Products for my 1964 Ford Custom?
The cheapest 1964 Ford Custom Performance and Racing Products we carry in stock are:
- Camshaft Bolt for Ford 352-427 (50287929) – $8.99
- 10 Degree Steel Retainer for 26120 Beehive Spring (50289146) – $10.99
- 7 Degree Steel Retainer for 3/8" Valves with 1.500"-1.550" Spring (50289506) – $10.99
- 7 Degree Steel Retainer for 11/32" Valves with 1.500"-1.550" Spring (50289132) – $10.99
- D4260 Flame-Thrower Distributor Rotor HEI/EST Black (10111551) – $11.99
What are the top-rated Performance and Racing Products that fit the 1964 Ford Custom?
Out of 626 reviews by customers, our 1964 Ford Custom Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1964 Ford Custom and their top-rated products:
- Performance Radiators
- Thermocap Radiator Cap (6900022) – $53.99
- Performance Fuel Systems
- Thermocap Radiator Cap (6900022) – $53.99
- Performance Shifters
- Thermocap Radiator Cap (6900022) – $53.99
What types of Performance and Racing Products do you sell for my 1964 Ford Custom?
As of 3/1/26, these are some of the most in-demand types of Performance and Racing Products for a 1964 Ford Custom:
Can I get help with 1964 Ford Custom Performance and Racing Product orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Performance and Racing Products and more.
What is your return policy for Ford Custom Performance and Racing Products?
Advance Auto Parts keeps returns simple. For new Ford Custom Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
