1963 Ford Thunderbird Drivetrains

Name: Spindle Washer - I.D. 13/16 In. O.D. 1-21/32 In. Thickness 3/32 In.
Brand: Dorman
SKU: 618-013.1
Price: 4.99 USD

Below you will find various in-demand Ford Drivetrains, components and accessories for your 1963 Thunderbird. Advance Auto Parts has popular Thunderbird parts like Spindles, Drive Shafts and Axles, Universal Joints and more. You’ll also find aftermarket and OEM Drivetrains for other Thunderbird model years including 1993, 1994, 1995, 1996, 1997, 2002, 2003, 2004, 2005 and more. Select a category of 1963 Ford Thunderbird Drivetrains below and start saving instantly.

Popular 1963 Ford Thunderbird Drivetrains Categories

Differential Oil

U-Joints

Rear Differential Cover Gaskets

Differential Open Unit and Components

Differential Bearings

Bearing Pullers

Drive Shaft Bearings

Differential Pinion Pilot Bearings

U-Joint Centering Yokes

Axle Shaft Bearings

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Clutch Packs

Differential Ring and Pinions

Differential Cases

Differential End Yokes

Differential Pinion Supports

Spindle Lock Nuts

Differential Spools

Differential Lock Springs

Differential Carrier Bearing Adjusters

Transfer Case Output Shaft Bearings

Differential Pinion Bearing Kits

Differential Ring Gear Bolts

Bearing Race Drivers

Spindle Lock Nut Thrust Washers

Spindle Retainers

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Automatic Transmission Differential Carrier Gaskets

Differential Housing O-Rings

Differential Side Gear Thrust Washers

Differential Pinion Gear Thrust Washers

Axle Shaft Studs

Differential Drive Pinion Gear Bearing Retainer Bolts

Differential Drive Pinion Oil Deflectors

Spindle Washers

Axle Shaft Bearing Retainers

Limited Slip Differential Assemblies

Differential Lock Washers

Differential Clutch Pack Clips

Differential Lock Thrust Blocks

Differential Pinion Bearing Spacers

Differential Bearing Adjuster Nut Lock Bolts

Axle Housing Fill Plugs

Differential Carrier Bearing Races

Drive Shaft Pinion Yoke Washers

Essential Drivetrains for 1963 Ford Thunderbirds

from

$4.99

This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$41.99

Product Features:

PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
STRONG AND DURABLE: Controlled heat treatment process for strength and durability
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$94.99

3.062″ side adjuster, Only Fits Yukon Ford 9″ Drop Out, new design ONLY.

Product Features:

Side adjuster
Fits Ford 9″
3.062″ designs only

from

$9.99

Crush Sleeve for Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9 3/8″, 9″ & 9.75″. .480″ long.

Product Features:

Crush sleeve for AMC Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9″ and 9.75″
0.480″ tall

from

$8.99

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

from

$5.99

This spindle nut retainer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$10.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

Fill plug
Fits Ford 9″

from

$5.99

Ford 7.5″ & 8.8″ ring gear bolt, standard Open & TracLoc. 7/16″ x 20.

Product Features:

Ring gear bolt for Ford 7.5″ and 8.8″
7/16″ x 20

from

$821.99

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.

Product Features:

Fits Ford 9″ with 28 spline axles
Trac Loc positraction
Clutch style positraction
Aggressive design
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$207.99

Standard open or TracLoc cross pin shafts and block in four pinion design for 9″ Ford.

Product Features:

Cross pin shaft and block kit
Fits Ford 9″
Includes cross pin block and three cross pin shafts

from

$9.99

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$7.99

Wheel Lug Stud

from

$569.99

Ford 9″ pinion Support, 35 spline, 10 hole, no races included.

Product Features:

Fits Ford 9″ with 35 spline pinion
Larger inner pinion bearing reduces gear deflection under high load
6061 aluminum
10 bolt holes
Does not include races

from

$123.99

Product Features:

CLUTCH PACK KIT 8.8″ FORD 1 KIT PER UNIT

from

$304.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses carrier bearings & races with an I.D. of 1.780″ and an O.D. of 2.891″. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

Fits Ford 9″ with LM102940 carrier race
Included are Timken bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve eliminator , thread locker, marking compound with brush, and gasket.

from

$615.99

Yukon Extra HD 3.062″ nodular Iron dropout for Ford 9″. Yukon nodular iron dropouts feature a 5/8″ cap bolt and forged caps for maximum strength. Rated up to 1200HP!

Product Features:

Fits Ford 9″
3.062″ carrier race diameter
Nodular iron for added strength

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$11.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$137.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$8.99

Pinion seal for 7.5″, 8.8″, and 9.75″ Ford, and also 1985-’86 9″ Ford.Yukon Mighty seal.

Product Features:

Pinion seal
Fits Ford 7.5″, 8.8″ and some 9.75″
2.785″ O.D.

from

$5.99

Product Features:

Copper washer
Fits Ford 8″ and 9″

from

$22.49

Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

from

$285.99

Yukon standard open spider gear kit for 8.8″ Ford (and IFS) with 28 spline axles and 3/4″ pin. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Ford 8.8″ open differential with 28 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$48.99

RngPnnInstlKt

from

$1211.99

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker uses 8620 internals and a patented design to provide maximum strength and reduce common failures. Assembled in the USA! This unit has been approved for competition in NASCAR National & Touring series. This is a race unit designed for extreme off road use or racing. All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This locker also fits 9.5″ & 10″ dropouts.

Product Features:

Fits Ford 9″ with 35 spline axles and loadbolt housing
Patented internal design reduces common locker failures
8620 internals for added strength
Assembled in the USA
Aggressive design for racing applications only

from

$7.99

High-quality Differential Component Shim

Product Features:

SHIM KIT FITS-8.25-F7.5-AMC20-GM0

from

$14.99

O-ring for 9″ Ford.Yukon Mighty seal.

Product Features:

Pinion support o-ring
Fits Ford 9″

from

$10.99

Standard Open & TracLoc pinion gear thrust washer for 7.5″ Ford.

Product Features:

Pinion gear thrust washer
Fits Ford 7.5″

Upgrade your 1963 Ford Thunderbird with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1963 Ford Thunderbird, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Drivetrains are key to keeping your Thunderbird functioning at its best. At Advance Auto Parts, we offer a wide selection of 335 Drivetrains for the 1963 Ford Thunderbird, designed to meet your needs without breaking the bank. From Spindle replacements to Drive Shafts and Axles upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1963 Ford Thunderbird at great prices. Our Drivetrains inventory for this model ranges from just $1.99 to $1,211.99, with an average price of $240.99. Our 335 Drivetrains in stock come from 14 trusted brands, so you’re sure to find the right part for your 1963 Ford Thunderbird without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1963 Ford Thunderbird, we stock popular OEM and aftermarket Drivetrains from top names like Moog, National, Dorman, and more. Moog Drivetrains start at just $29.99 and boast an impressive 4.5 stars average rating from customers. National and Dorman also bring quality to the table, with Drivetrains available starting at $3.49, and at an average 4.3 stars rating. With 1,643 customer reviews and counting, our 1963 Ford Thunderbird Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1963 Ford Thunderbird is always ready to roll. We’re committed to providing you with everything you need to keep your Thunderbird in top shape, all in one place. Start shopping confidently below for your 1963 Ford Thunderbird!

Best-Selling Spindles for 1963 Ford Thunderbirds

Enhance the driving experience in your Ford with 6 quality Spindle components, starting at $3.49.

show more show less

from

$3.49

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$5.49

Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$3.99

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$5.99

Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$4.79

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$14.49

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Top Picks for 1963 Ford Thunderbird Universal Joints

Upgrade Ford Thunderbirds with top-quality Universal Joints parts, including 17 OEM and aftermarket selections for your 1963 model.

show more show less

from

$42.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

Product Features:

OE engineering and field tested experience is why the Spicer brand is the most trusted in the industry.
Forged with high-quality steel, these u-joints are heat treated and case-hardened with precision to specific levels, ensuring optimal strength and durability.
The process of precision grinding the seal and bearing surfaces helps to improve the life of the seal and bearing.
Zerk allows for lubricating at regular intervals to help extend the life of the part.

from

$34.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$31.99

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$29.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$42.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$40.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$44.99

Yukon 1310 U/Joint with zerk fitting on cross. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$59.99

Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.

from

$109.99

Yukon 1310 to Mechanics 3R adapter U/Joint.

from

$63.99

Yukon 1350 Lifetime Series U/Joint. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring.

from

$51.99

Yukon 1350 U/Joint with zerk fitting. 3.625″ snap ring span, 1.118″ cap diameter. Outside snap ring.

from

$57.99

1310 Yukon Lifetime U/joint. 1.718″ snap ring span, 1.062″ cap diameter. Inside snap ring.

from

$111.99

Yukon 1350 to Mechanics 3R adaptor U/joint.

from

$74.99

1.250″ pinion adaptor sleeve (stock pinion into large support).

Product Features:

Adapter sleeve
Fits Ford 9″
Adapts 28 spline pinion into 35 spline pinion support

from

$36.99

from

$22.49

KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

In-Demand Transfer Cases for 1963 Ford Thunderbirds

Select from 4 premium Transfer Cases parts for your 1963 Ford Thunderbird, with prices ranging from $7.79 to $62.99.

show more show less

from

$36.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$7.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$11.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$62.99

The FAG repair sleeve is a precision element that provides additional sealing for damaged shafts. Made of heat-treated stainless steel, the FAG repair sleeve signifcantly increases the life of the shaft and prevents premature wear. Since no shaft removal or machining is required during the repair, the repair sleeve is a cost effective repair solution to protect damaged surfaces.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

Most Sold 1963 Ford Thunderbird Differentials

Explore our best-selling Ford parts for the 1963 Thunderbird among 299 OEM and aftermarket options starting from $1.99.

show more show less

from

$7.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$9.99

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$551.99

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.Powertrax® = Extreme Traction Systems!

from

$26.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$6.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$6.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$5.99

Product Features:

Copper washer
Fits Ford 8″ and 9″

from

$37.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$4.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

PREMIUM MATERIALS — Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION — Crowned raceways for even load distribution
OE-STYLE DESIGN — Engineered to meet OE specifications
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$9.99

Crush Sleeve for Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9 3/8″, 9″ & 9.75″. .480″ long.

Product Features:

Crush sleeve for AMC Model 20, Ford 10.25″, 10.5″, 7.5″, 8.8″, 9″ and 9.75″
0.480″ tall

from

$8.99

Replacement outer oil slinger for Ford 7.5″, 8.8″, 9″, 10.25″, Nissan Titan rear, Dana 44 Rubicon & 44 JK non-Rubicon.

Product Features:

Outer oil slinger for Ford 10.25″, 7.5″, 8.8″ and 9″ also Jeep JK and Nissan Titan rear

from

$5.99

Ford 8″ & 9″ standard Open, AG, & Detroit locker ring gear bolt. 7/16″ head, .925″ long.

Product Features:

Ring gear bolt for Ford 8″ and 9″
For use with standard open carrier, Auburn Gear limited slip and Detroit Locker
7/16″ head
.925″ long

from

$5.99

Ford 8″ & 9″ standard Open, AG, & Detroit locker ring gear bolt, 1.0″ long, Ford.

Product Features:

Ring gear bolt for Ford 8″ and 9″
For use with standard open carrier, Auburn Gear limited slip and Detroit Locker
1.0″ long

from

$4.99

Ford 8″ & 9″ TracLoc ring gear bolt, 1-1/4″ long.

Product Features:

Ring gear bolt for Ford 8″ and 9″
For use with Trac Loc limited slip
1.25″ long

from

$1.99

Product Features:

BOLT 9″ FORD OPEN R.G. SAME AS M-4216A200

from

$7.99

Pinion nut for Ford 7.5″, 8″, 8.8″, 9 3/8″ & 9″. 1 1/6″ socket, 3/4″ x 20 thread.

Product Features:

Pinion nut for Ford 7.5″, 8″ and 9″
3/4″ x 20 thread
1 1/6″ socket

from

$11.99

9″ Ford gasket.

Product Features:

Dropout gasket
Fits Ford 9″

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$8.49

Product Features:

PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$21.99

8.75″ Chrysler & 9″ Ford preload shim kit.

Product Features:

Preload shim kit for Ford 9″ and Chrysler 8.75″ with ’41’ and ’42’ case housing

from

$5.99

Product Features:

Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
0.030″ thick

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$38.99

8.6″ GM 99-08 PINION Bearing & SEAL KIT .

Product Features:

Pilot bearing
Fits Ford 9″
0.656″ thick

from

$6.99

Pinion support bolt for 8″ and 9″ Ford.

Product Features:

Pinion support bolt for Ford 8″ and 9″
3/8″ x 24 thread
1.0″ long

Top-Rated Drivetrains Brands For Your 1963 Ford Thunderbird

Shop for the best-rated brands offering Drivetrains and other products for your 1963 Ford Thunderbirds. Below you’ll find some of our best rated Drivetrains from Moog, National, and Dorman, and more. Drivetrains from these brands that fit a 1963 Thunderbird start at just $3.49 and are rated as high as 4.5 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Moog 1963 Ford Thunderbird Drivetrains

When it comes to maintaining or upgrading your 1963 Ford Thunderbird, using quality Drivetrains is essential to ensure durability and a perfect fit. Moog ticks all of those boxes. We offer a wide selection of Moog Drivetrains, specifically designed for the 1963 Ford Thunderbird. With over 3 Moog brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $29.99, with an average price of just $35.99. Plus, with over 208 customer reviews and an average rating of 4.5 stars, you can trust that our Moog Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $34.99

(143)

Greaseable Premium Universal Joint

“Good fit”

from $42.99

(35)

Greaseable Super Strength Universal Joint

“Good ujoint”

from $29.99

(30)

Non-Greaseable Super Strength Universal Joint

“Direct replacement for the OEM joints”

Popular National 1963 Ford Thunderbird Drivetrains

National auto parts is one of the highest quality Drivetrain brands in the market. Any 1963 Ford Thunderbird owner should feel confident when installing genuine National parts in their vehicle. To ensure the best fit and performance for your 1963 Thunderbird, Advance Auto Parts carries a full inventory of 3 National Drivetrains. Plus you will be keeping your Ford in peak condition while saving money because prices on these National Drivetrains range from $7.99 to $36.49, plus, with more than 14 customer reviews and an impressive 4.3 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from $7.99

(4)

Bearing Race

“Goes with M88010 bearing cup. Application was the pinion bearing race for a Ford 9 Inch on a 1957 Ford F-100.”

from $36.49

(1)

Shaft Repair Sleeve

“Fixed my Ford F-150 4.2. Fit well and installation tool seated the sleeve exactly where it needed to be. Super easy to use and covered the grooved s”

from $13.99

(9)

Bearing

“as advertised”

FAQs for 1963 Ford Thunderbird Drivetrains

Which Drivetrains are best-sellers for 1963 Ford Thunderbirds?

Out of 335 Drivetrains that fit 1963 Ford Thunderbirds, the following parts are the top sellers:

Universal Joint (10265720) – $31.99
Tapered Cone/Cup Wheel Bearing Set (5050723) – $26.99
Universal Joint, Greaseable 1330 Series OSR (10854997) – $42.99

What’s the price range for 1963 Ford Thunderbird Drivetrains?

Drivetrain prices for the 1963 Ford Thunderbird start at $1.99 and go up to $1,211.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1963 Ford Thunderbird?

The average price for Drivetrains for the 1963 Ford Thunderbird is $240.99. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Ford Thunderbird model years?

Yes, we currently carry Drivetrains for 45 model years of Ford Thunderbirds between 1955 and 2005. Drivetrains are bought most frequently for the following model years: 2005, 2004, 2003, 2002, 1997, 1996, 1995, 1994, and 1993.

What are the cheapest Drivetrains for my 1963 Ford Thunderbird?

The cheapest 1963 Ford Thunderbird Drivetrains we carry in stock are:

Ring Gear Bolt (19640279) – $1.99
Differential Crush Sleeve (10282338) – $2.99
Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (21260547) – $3.49
Spindle Washer – I.D. 3/4 In. O.D. 1-21/32 In. Thickness 3/32 In. (22972449) – $3.99
Trac Loc Ring Gear Bolt Washer For 8" And 9" Ford (11643118) – $3.99

What are the top-rated Drivetrains that fit the 1963 Ford Thunderbird?

Out of 1,643 reviews by customers, our 1963 Ford Thunderbird Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1963 Ford Thunderbird and their top-rated products:

Universal Joints
- Universal Joint, Greaseable 1330 Series OSR (10854997) – $42.99
- Greaseable Premium Universal Joint (10086740) – $34.99
- Non-Greaseable Super Strength Universal Joint (10087058) – $29.99
Spindles
- Universal Joint, Greaseable 1330 Series OSR (10854997) – $42.99
- Greaseable Premium Universal Joint (10086740) – $34.99
- Non-Greaseable Super Strength Universal Joint (10087058) – $29.99
Differentials
- Universal Joint, Greaseable 1330 Series OSR (10854997) – $42.99
- Greaseable Premium Universal Joint (10086740) – $34.99
- Non-Greaseable Super Strength Universal Joint (10087058) – $29.99

What types of Drivetrains do you sell for my 1963 Ford Thunderbird?

As of 11/2/25, these are some of the most in-demand types of Drivetrains for a 1963 Ford Thunderbird:

Can I get help with 1963 Ford Thunderbird Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Drivetrains and more.

What is your return policy for Ford Thunderbird Drivetrains?

Advance Auto Parts keeps returns simple. For new Ford Thunderbird Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1963 Ford Thunderbird Drivetrains

Dorman – Spindle Washer – I.D. 13/16 In. O.D. 1-21/32 In. Thickness 3/32 In. (Part No.618-013.1)

National – Multi-Purpose Bearing (Part No.R-1535-TAV)

Yukon Gear – 3.062" Side Adjuster For Ford 9" (Part No.32139)

Yukon Gear – Crush Sleeve (Part No.33085)

Yukon Gear – Outer Oil Slinger For Ford 7.5", 8.8", 9", 10.25" (Part No.33022)

Dorman – Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm (Sold by each) (Part No.615-073)

Yukon Gear – Fill Plug For Ford 9", 1/2" Thread (Part No.33539)

Yukon Gear – Ford 7.5" & 8.8" Ring Gear Bolt, Standard Open & Tracloc (Part No.33053)

Yukon Gear – Trac Loc For Ford 9" Wtih 28 Spline Axles – Aggressive Design (Part No.26007)

Yukon Gear – Standard Open Or Tracloc Cross Pin Shafts And Block In Four Pinion Design For 9" Ford (Part No.33333)

Felpro – Differential Carrier Gasket Oval Shaped 10 Bolt Hole Gasket (Part No.RDS 55074)

Yukon Gear – Wheel Lug Stud (Part No.33571)

Yukon Gear – Ford 9" Pinion Support, 35 Spline, 10 Hole, No Races Included (Part No.32165)

Motive Gear – Differential Clutch Pack (Part No.F8.8CPK)

Yukon Gear – Master Overhaul Kit For Ford 9" LM102910 Differential, With Crush Sleeve Eliminator (Part No.14156)

Yukon Gear – Extra HD 3.062" Nodular Iron Dropout For Ford 9" (Part No.32099)

Yukon Gear – The Carrier Bearing Puller (Part No.56034)

Driveworks – Taper Bearing Cone (Part No.S-M-88048)

Dorman – Differential Pinion Yoke Assembly (Part No.697-530)

Yukon Gear – Pinion Seal For 7.5", 8.8", And 9.75" Ford, And Also 1985-’86 9" Ford (Part No.30037)

Yukon Gear – Copper Washer For Ford 9" & 8" Dropout Housing (Part No.32339)

MOOG Driveline Products – Universal Joint (Part No.444)

Yukon Gear – Standard Open Spider Gear Kit For 8.8" Ford (And IFS) With 28 Spline Axles (Part No.16019)

Richmond Gear – RngPnnInstlKt (Part No.83-1011-B)

Yukon Gear – Grizzly Locker For Ford 9" Differential With 35 Spline Axles, Racing Design, For Load Bolt D/O (Part No.28030)

Motive Gear – Differential Pinion Shim Kit (Part No.1100)

Yukon Gear – O-Ring For 9" Ford (Part No.30028)

Yukon Gear – Standard Open & Tracloc Pinion Gear And Thrust Washer For 7.5" Ford (Part No.33296)

Dorman – Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (Part No.615-072.1)

Dorman – Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm (Part No.615-073.1)

Dorman – Spindle Washer – I.D. 3/4 In. O.D. 1-21/32 In. Thickness 3/32 In. (Part No.618-005.1)

Dorman – Spindle Nut 3/4 In.-16 and M20 In.-1.0 Hex Size 1-1/16 In. and 27mm (Sold by each) (Part No.615-073)

Dorman – Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (sold by each) (Part No.615-072)

Dorman – Spindle Washer – I.D. 3/4 In. O.D. 1-21/32 In. Thickness 3/32 In. (Sold by each) (Part No.618-005)

National – Bearing (Part No.M88048)

Yukon Gear – Fill Plug For Ford 9", 1/2" Thread (Part No.33539)

Yukon Gear – Axle Bearing Retainer For Ford 9", Large Bearing, 1/2" Bolt Holes (Part No.33467)

Yukon Gear – The Carrier Bearing Puller (Part No.56034)

Yukon Gear – Conversion Bearing For Small Bearing Ford 9" Axle In Large Bearing Housing (Part No.18046)

Yukon Gear – Adaptor Washer For 28 Spline Pinion In Oversize Support, For 9" Ford (Part No.32240)

Yukon Gear – Axle Bearing Retainer For Ford 9", Large & Small Bearing, 3/8" Bolt Holes (Part No.33466)

Yukon Gear – Axle Bearing Retainer For Ford 9", Small Bearing, 3/8" Bolt Holes (Part No.33468)

Yukon Gear – Model 20 & Model 35 Axle Stud 1/2"-20 X 1.625" Length, 0.620" Dia – Knurl (Part No.33181)

Spicer – Universal Joint, Greaseable 1330 Series OSR (Part No.5-213X)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.354)

Driveworks – Universal Joint (Part No.DW-354)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.254)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.270)

Driveworks – Universal Joint (Part No.DW-270)

Spicer – Universal Joint (Part No.5-1330X)

Yukon Gear – 1310 U/Joint With Zerk Fitting On Cross (Part No.42008)

Yukon Gear – 1310 To 1330 Adapter U/Joint (Part No.42005)

Yukon Gear – 1310 To Mechanics 3R Adapter U/Joint (Part No.42013)

Yukon Gear – 1350 Lifetime Series U/Joint (Part No.42021)

Yukon Gear – 1350 U/Joint With Zerk Fitting (Part No.42010)

Yukon Gear – 1310 Lifetime U/Joint (Part No.42003)

Yukon Gear – 1350 To Mechanics 3R Adaptor U/Joint (Part No.42001)

Yukon Gear – 1.250" Pinion Adaptor Sleeve (Stock Pinion Into Large Support) (Part No.32239)

Spicer – Universal Joint (Part No.5-1330-1X)

MOOG Driveline Products – Universal Joint (Part No.444)

National – Shaft Repair Sleeve (Part No.99187)

National – Bearing (Part No.LM67048)

Driveworks – Taper Bearing Cone (Part No.S-M-88048)

FAG US – Repair Sleeve (Part No.SR3501)

National – Bearing Race (Part No.M88010)

Felpro – Differential Carrier Gasket Oval Shaped 10 Bolt Hole Gasket (Part No.RDS 55074)

Powertrax – No-Slip Traction System (Part No.9206902800)

Driveworks – Tapered Cone/Cup Wheel Bearing Set (Part No.S-A-35)

Motive Gear – Differential Pinion Nut (Part No.379570S)

Driveworks – Oil Seal (Part No.S-7044NA)

Yukon Gear – Copper Washer For Ford 9" & 8" Dropout Housing (Part No.32339)

National – Shaft Repair Sleeve (Part No.99181)

National – Bearing Race (Part No.LM67010)

Yukon Gear – Crush Sleeve (Part No.33085)

Yukon Gear – Outer Oil Slinger For Ford 7.5", 8.8", 9", 10.25" (Part No.33022)

Yukon Gear – Ford 8" & 9" Standard Open, Ag, & Detroit Locker Ring Gear Bolt (Part No.33058)

Yukon Gear – Ford 8" & 9" Standard Open, Ag, & Detroit Locker Ring Gear Bolt (Part No.33043)

Yukon Gear – Ford 8" & 9" Tracloc Ring Gear Bolt (Part No.33044)

Motive Gear – Ring Gear Bolt (Part No.D8OZ4216B)