1963 Dodge D200 Series Drivetrains

Below you will find various in-demand Dodge Drivetrains, components and accessories for your 1963 D200 Series. Advance Auto Parts has popular D200 Series parts like Universal Joints, Drive Shafts and Axles, Differentials and more. You’ll also find aftermarket and OEM Drivetrains for other D200 Series model years including 1960, 1961, 1962, 1964, 1965, 1966, 1967 and more. Select a category of 1963 Dodge D200 Series Drivetrains below and start saving instantly.

Please Select your Vehicle to See Exact Fit Parts

Popular 1963 Dodge D200 Series Drivetrains Categories

Differential Oil

U-Joints

Rear Differential Cover Gaskets

Drive Shaft Center Supports

Differential Open Unit and Components

Differential Covers

Center Support Bearings

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Differential Bearings

Differential Axle Shafts

Drive Shaft Bearings

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

Differential Pinion Pilot Bearings

U-Joint Centering Yokes

Differential Cover Bolts

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Differential Clutch Packs

Differential Ring and Pinions

U-Joint U-Bolt Kits

Differential Cases

Differential End Yokes

Spindle Lock Nuts

Differential Lock Assemblies

Differential Air System Seal Housings

Differential Spools

Differential Carrier Bearings

Front Differential Cover Gaskets

Transfer Case Output Shaft Bearings

Differential Pinion Bearing Kits

Drive Shaft Seals

Complete Differentials

Differential Ring Gear Bolts

Bearing Race Drivers

Spindle Lock Nut Thrust Washers

Differential Carrier Bearing Shims

Input Shaft Seals

Spindle Retainers

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Gear Install Kits

Differential Cross Pins

Automatic Transmission Differential Carrier Gaskets

Differential Housing O-Rings

Differential Side Gear Thrust Washers

Differential Pinion Bearing Baffles

Differential Pinion Gear Thrust Washers

Differential Drive Pinion Oil Deflectors

Differential Carrier Bolts

Differential Pinion Gear Washers

Limited Slip Differential Assemblies

Universal Joint Strap Bolts

Differential Clutch Pack Clips

Differential Bearing Adjuster Nut Lock Bolts

Differential Lock Thrust Blocks

Axle Housing Fill Plugs

Essential Drivetrains for 1963 Dodge D200 Series

from

$15.99

Bolt/screw for adjuster lock for Chrysler 7.25″, 8.25″, 8.75″, 9.25″.

Product Features:

Side adjuster lock bolt
Fits Chrysler 7.25″, 8.25″, 8.75″ and 9.25″

from

$40.99

Anchor 6038 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 4 Lbs
BEARING ID / BORE: 1.5750 In. / 40 mm
CENTERLINE: 2.48 In. / 63 mm
Mount Width: 6.62 In. / 168 mm
Style: Round Frame
Not Pictured: Two Dust Shields

from

$152.99

Set-up bearing (one bearing). HM803149. No return.

Product Features:

Set up bearing
Fits HM803149 pinion bearing
Easily slips on and off pinion journal to allow for pinion depth adjustment

from

$27.99

Product Features:

Bulkhead fitting

from

$86.99

8.75″ Chrysler 89 solid crush sleeve replacement spacer, preload. This item is compatible with ’89 case dropouts only.

Product Features:

Crush sleeve eliminator kit for Chrysler 8.75″ with ’89’ case housing

from

$295.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 60 rear
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$49.99

7260 U/joint strap, Small Chrysler w/ bolts, 7.25, 8.25, 8.75, 9.25.

Product Features:

u-joint strap kit
Fits Chrysler 7.25″, 8.25″ 8.75″ and 9.25″ rear
7260 u-joint size
Includes two straps and four bolts

from

$232.99

Full-floating, 35 spline diameter, non-drilled blank axle shaft for Dana 60. 40″ inches long. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H axles come with a one year warranty against manufacturing defects.

from

$203.99

Yukon replacement yoke for Dana 44-HD, 60, and 70 with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60, 70, 70U and 70HD
29 spline
1310 u-joint size
3.219″ snap ring span
1.062″ cap diameter
Outside snap ring design
U-bolt style

from

$5.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; single-lip
Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$46.99

Cross pin shaft for standard open Chrysler 9.25″, .860″ diameter. Will not fit posi!

Product Features:

Cross pin shaft for Chrysler 9.25″
Fits standard open differentials only
0.860″ diameter

from

$67.99

Powr Lok button kit
Fits Dana Spicer 30, 44 and Chrysler 8.75″

from

$8.99

Positraction clutch guide.

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
Compatible with Dura Grip positractions only

from

$564.99

89 housing nodular Iron Drop Out case, up to 500 HP, Billet adjuster for 8.75″ Chrysler. This dropout does not come with fill plug (Part number CHY612017).

Product Features:

Fits Chrysler 8.75″
’89’ case design
Nodular iron for added strength

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$219.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits M88010 race
All steel construction

from

$213.99

Yukon yoke for Chrysler 8.75″ with 10 spline pinion and a 7260 U/joint size. 2.125″ snap ring span, 1.078″ cap diameter. Inside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 8.75″
10 spline
7260 u-joint size
Inside snap ring design
2.125″ snap ring span
1.078″ cap diameter
Strap style

from

$674.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon has an updated, proprietary, design that provides longer life and higher durability than the competition. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty. We reccomend an OEM gear for van applications. This gear set is for ’09 and older applications only.

Product Features:

Fits 2010 and down Chrysler 9.25″ rear
9.25″ ring gear diameter
29 spline pinion
12 ring gear bolts
3.55 ratio

from

$26.99

Spartan spring & pin kit, fits larger designs.

Product Features:

Fits Dana Spicer 60
Replacement alignment pin and spring kit

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$84.99

Standard Open notched cross pin shaft for 9.25″ Chrysler.

Product Features:

Cross pin shaft
Fits Chrysler 9.25″
Standard open carrier only
Notched

from

$183.99

Worn or damaged differential end yoke causing driveline Vibrations! This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$1015.00

USA Standard Gear Power Lok posi for Chrysler 8.75″, smooth design

Product Features:

Gear Power Lok Posi LSD
Fits Chrysler 8.75″
Smooth design
Positraction

from

$4.79

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$4.99

Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.

Product Features:

Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
1/2″ x 18 thread

from

$89.99

Chrome replacement cover for Dana 60 and 61(not reverse rotation!).

Product Features:

Fits standard rotation Dana Spicer 60
Chrome

from

$6.99

Product Features:

DANA PRELOAD SHIMS (D60 & D70)

from

$9.99

Chrysler 8.75″ (coarse spline) pinion nut washer.

Product Features:

Pinion nut washer
Fits Chrysler 8.75″ with 10 spline pinion

Upgrade your 1963 Dodge D200 Series with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1963 Dodge D200 Series, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Dodge or enhancing its overall performance, Drivetrains are key to keeping your D200 Series functioning at its best. At Advance Auto Parts, we offer a wide selection of 306 Drivetrains for the 1963 Dodge D200 Series, designed to meet your needs without breaking the bank. From Universal Joint replacements to Drive Shafts and Axles upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1963 Dodge D200 Series at great prices. Our Drivetrains inventory for this model ranges from just $3.49 to $1,566.99, with an average price of $243.55. Our 306 Drivetrains in stock come from 15 trusted brands, so you’re sure to find the right part for your 1963 Dodge D200 Series without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1963 Dodge D200 Series, we stock popular OEM and aftermarket Drivetrains from top names like Moog, National, Dorman, and more. Moog Drivetrains start at just $36.99 and boast an impressive 4.5 stars average rating from customers. National and Dorman also bring quality to the table, with Drivetrains available starting at $3.49, and at an average 4.3 stars rating. With 214 customer reviews and counting, our 1963 Dodge D200 Series Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1963 Dodge D200 Series is always ready to roll. We’re committed to providing you with everything you need to keep your D200 Series in top shape, all in one place. Start shopping confidently below for your 1963 Dodge D200 Series!

Best-Selling Universal Joints for 1963 Dodge D200 Series

Enhance the driving experience in your Dodge with 39 quality Universal Joint components, starting at $3.99.

show more show less

from

$31.99

Driveworks Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. Driveworks Universal Joints are constructed from quality materials for extended durability. Driveworks Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearing cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves are designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$44.99

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$38.99

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
GREASEABLE DESIGN – Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$36.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$26.99

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

For U-Joints 315G, 317, 319 & 457
Contains two 1-1/2″ bolt center clamps and four 1/4-28 x 5/8″ cap screws

from

$29.99

Product Features:

BUILT TO LAST – Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
CORROSION PROTECTION – Exclusive MICRO SHIELD coating protects against rust and corrosion
KEEPS DIRT OUT – Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$36.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$34.99

Product Features:

COMPREHENSIVE COVERAGE – Available for foreign and domestic nameplates
GREASABLE DESIGN – Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT – Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE – Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$39.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles in a wide variety of applications, from light vehicle to commercial and off-highway.

from

$10.99

For U-Joints 316 & 458
Contains two 1.54″ bolt center clamps and four 1/4-28 x 5/8″ cap screws

from

$45.99

from

$59.99

Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.

from

$34.99

1310 U-bolts, 5/16″ x 1-3/8″ Dana 30, Dana 44, 8.2″, 12P, 12T, VET, Model 20.

Product Features:

u-joint u-bolt kit
Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
1310 u-joint size
Includes two u-bolts and four nuts

from

$16.99

1350 & 1410 U/joint U-bolts, 3/8″ X 1-11/16″, kit.

Product Features:

u-joint u-bolt kit
Fits 1350 and 1410 u-joint size
Includes two u-bolts and four nuts

from

$78.99

Yukon 1350 to 1410 conversion u/joint.

from

$109.99

Yukon 1310 to Mechanics 3R adapter U/Joint.

from

$63.99

Yukon 1350 Lifetime Series U/Joint. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring.

from

$61.99

Yukon 1330 Dual-size cap U/Joint. 3.625″ snap ring span. One set of caps is 1.125″ in diameter and the other is 1.062″. Outside snap ring.

from

$52.99

7290 U/joint strap kit (4 bolts and 2 straps) for Chrysler 7.25″, 8.25″, 8.75″, and 9.25″.

Product Features:

u-joint strap kit
Fits Chrysler 7.25″, 8.25″ 8.75″ and 9.25″ rear
7290 u-joint size
Includes two straps and four bolts

from

$51.99

Yukon 1350 U/Joint with zerk fitting. 3.625″ snap ring span, 1.118″ cap diameter. Outside snap ring.

from

$53.99

1330 Yukon Lifetime U/Joint. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$51.99

Yukon 1330 U/Joint with zerk fitting. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$57.99

1310 Yukon Lifetime U/joint. 1.718″ snap ring span, 1.062″ cap diameter. Inside snap ring.

Most Popular 1963 Dodge D200 Series Drive Shafts and Axles

Customize your Dodge with 20 Drive Shafts and Axles products like Axle Shaft Seals, Center Support Bearings, and Drive Shaft Bearings, all priced under $414.99.

show more show less

from

$40.99

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 4 Lbs
BEARING ID / BORE: 1.5750 In. / 40 mm
CENTERLINE: 2.48 In. / 63 mm
Mount Width: 6.62 In. / 168 mm
Style: Round Frame
Not Pictured: Two Dust Shields

from

$17.99

Product Features:

CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN: Engineered to meet OE specifications
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$44.99

Designed to meet or exceed OE quality, premium-quality bearings from National are manufactured to exacting standards to deliver lasting performance and extended bearing life.

Product Features:

BUILT TO LAST – Advanced heat treatment process for strength
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE – Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$21.99

Anchor 6056 Center support bearings support a driveshaft between transmission and differential. This mount relieves stress on driveline components. Each part is engineered and designed to OE Standards. Natural and SBR rubber provide maximum life and performance. Steel fasteners are heat treated grade 5 bolts. A special bonding agent is used to ensure a rubber to metal bond. Rubber material is mixed to specific Durometer, hardness.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 3 Lbs
BEARING ID / BORE: 1.3780 In. / 35 mm
CENTERLINE: 2.28 In. / 58 mm
Mount Width: 6.62 In. / 168 mm
Style: Round Frame
Complete Mount

from

$20.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

BUILT TO LAST — Advanced heat treatment process for strength
PREMIUM MATERIALS — Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE — Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE — Industry-leading coverage for domestic and import applications
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$8.99

8.75″ Chrysler inner axle seal, use w/set7.Yukon Mighty seal.

Product Features:

Rear inner axle seal
Fits Chrysler 8.75″ rear
Tapered rolling bearing design only

from

$15.99

8.75″ Chrysler outer axle seal, use w/set7.Yukon Mighty seal.

Product Features:

Rear outer axle seal
Fits Chrysler 8.75″ rear
Tapered rolling bearing design only

from

$30.49

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool

from

$7.99

Product Features:

Pinion yoke dust shield
Fits Dana Spicer 60 and 70

from

$35.99

Product Features:

BUILT TO LAST: Advanced heat treatment process for strength
PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$9.99

Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality

Product Features:

Fill plug
Fits Chrysler 8.75″

from

$414.99

Yukon billet replacement yoke for Dana 60 and 70 with 29 spline pinion and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60 and 70
29 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
U-bolt style

from

$271.99

Yukon replacement yoke for Dana 60 and 70 with a 1330 U/joint size. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects. This is a u/bolt style yoke.

Product Features:

Fits Dana Spicer 60 and 70
29 spline
1330 u-joint size
Outside snap ring design
3.625″ snap ring span
1.062″ cap diameter
U-bolt style

from

$266.99

Yukon yoke for Chrysler 8.75″ with 10 spline pinion and a 7290 U/joint size (1350 with U/joint adapter.) All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 8.75″
10 spline
7290 u-joint size
Inside snap ring design
2.625″ snap ring span
1.125″ cap diameter
Strap style

from

$233.99

Yukon replacement yoke for Dana 44-HD, 60, and 70 with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60 and 70
29 spline
1310 u-joint size
Outside snap ring design
3.219″ snap ring span
1.062″ cap diameter
Strap style

from

$219.99

Yukon replacement yoke for Dana 60 and 70 with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60, 70, 70U and 70HD
29 spline
1350 u-joint size
3.625″ snap ring span
1.188″ cap diameter
Outside snap ring design
U-bolt style

from

$213.99

Fits Chrysler 8.75″
10 spline
7260 u-joint size
Inside snap ring design
2.125″ snap ring span
1.078″ cap diameter
Strap style

from

$188.99

Yukon yoke for Chrysler 8.75″ with 29 spline pinion and a 7260 U/joint size. 3.125″ snap ring span, 1.078″ cap diameter. Inside snap ring.This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler 8.75″
29 spline
7260 u-joint size
2.125″ snap ring span
1.078″ cap diameter
Inside snap ring design
Strap style

from

$50.99

The part you need. The name you trust. Spicer driveline components deliver top performance and value. These center bearing kits are manufactured to the same genuine standards you’ve come to expect from the most reliable name in driveshaft parts.

Product Features:

Dana manufactured Spicer center bearing kit
Interchangeable with OE component
Comes as a complete kit to replace, repair, or refurbish
Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace

from

$49.99

Dana manufactured Spicer center bearing kit
Interchangeable with OE component
Comes as a complete kit to replace, repair, or refurbish
Latest production upgrades ensure genuine Spicer parts are as good or better than the OE parts they replace

Top Picks for 1963 Dodge D200 Series Differentials

Upgrade Dodge D200 Series with top-quality Differentials parts, including 230 OEM and aftermarket selections for your 1963 model.

show more show less

from

$38.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$7.49

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$22.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$4.99

Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.

Product Features:

Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
1/2″ x 18 thread

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$13.99

Product Features:

Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80

from

$8.99

Ring gear bolt for Chrysler 7.25″, 8″ IFS, 8.25″, 8.75″ & GM 7.2″ IFS front. 3/8″ x 24.

Product Features:

Ring gear bolt for Chrysler 7.25″, 8.0″ IFS and 8.75″
3/8″ x 24 thread
.866″ long

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$16.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$10.99

Pinion nut for Chrysler 7.25″, 8.0″ IFS, 8.25″, 8.75″ fine spline, 9.25″ front & rear, 7/16″ x 14.

Product Features:

Pinion nut for Chrysler 8.0″ IFS, 8.25″, 8.75″ with 29 spline pinion and 9.25″ rear
7/8″ x 14 thread

from

$6.99

Product Features:

DANA PRELOAD SHIMS (D60 & D70)

from

$21.99

8.75″ Chrysler & 9″ Ford preload shim kit.

Product Features:

Preload shim kit for Ford 9″ and Chrysler 8.75″ with ’41’ and ’42’ case housing

from

$19.99

Product Features:

Pinion preload shims for Dana Spicer 60 and 70U

from

$15.99

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$26.99

Product Features:

Pinion nut
Fits Chrysler 7.25″, 8.0″, 8.25″, 9.25″ and 8.75″ with 29 spline pinion

from

$12.99

8.75″ Chrysler gasket.

Product Features:

Dropout gasket
Fits Chrysler 8.75″

from

$137.99

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil

from

$79.99

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

Seal housing for Dana Spicer 60
Includes o-rings

In-Demand Spindles for 1963 Dodge D200 Series

Select from 13 premium Spindles parts for your 1963 Dodge D200 Series, with prices ranging from $3.49 to $27.99.

show more show less

from

$3.49

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$5.49

This spindle nut retainer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$5.99

Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$4.79

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$8.99

Spindle nut retainer, 2.030″ I.D., 8 bent over tabs. This replaces Spicer part number 33733.

Product Features:

Spindle nut retainer for Dana Spicer 60, 70, 70U and 70HD
2.030″ I.D.
8 bent over tabs

from

$9.99

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$6.29

This spindle nut washer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$26.99

Spindle nut for Dana 60 & 70, 1.940″ I.D., with plastic ring. This replaces Spicer part number 39695.

Product Features:

Spindle nut
Fits Dana Spicer 60 and 70
1.940″ I.D.
Has plastic inner ring

from

$10.99

Spindle nut retainer for Dana 60 & 70, 1.830″ I.D., 10 outer tabs. This replaces Spicer part number 30637.

Product Features:

Spindle nut retainer for Dana Spicer 60, 70, 70U and 70HD
1.830″ I.D.
10 outer tabs

from

$6.99

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$27.99

Spindle nut, 2.065″ I.D., six slots. This replaces Spicer part number 36635.

Product Features:

Spindle nut
6 slots
2.065″ I.D.

from

$15.99

Spindle nut for Dana 60, 1.750″ I.D., 6 sided. This replaces Spicer part number 30636.

Product Features:

Spindle nut
Fits Dana Spicer 60
6 sides
1.750″ I.D.

from

$7.99

Direct replacement – this spindle nut washer matches the fit and function of the factory part on specified years, makes and models
Ideal solution – this washer is a reliable replacement for an original part that is missing or has failed due to wear
Durable construction – this part is made from quality materials to ensure reliable performance and Length service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Most Sold 1963 Dodge D200 Series Transfer Cases

Explore our best-selling Dodge parts for the 1963 D200 Series among 4 OEM and aftermarket options starting from $7.29.

show more show less

from

$22.79

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$7.29

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Design type: spring loaded; single-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$10.99

Design type: spring loaded; multi-lip
Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
Good low temperature capability
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$8.89

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

Top-Rated Drivetrains Brands For Your 1963 Dodge D200 Series

Shop for the best-rated brands offering Drivetrains and other products for your 1963 Dodge D200 Series. Below you’ll find some of our best rated Drivetrains from Moog, National, and Dorman, and more. Drivetrains from these brands that fit a 1963 D200 Series start at just $3.49 and are rated as high as 4.5 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Moog 1963 Dodge D200 Series Drivetrains

When it comes to maintaining or upgrading your 1963 Dodge D200 Series, using quality Drivetrains is essential to ensure durability and a perfect fit. Moog ticks all of those boxes. We offer a wide selection of Moog Drivetrains, specifically designed for the 1963 Dodge D200 Series. With over 3 Moog brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $36.99, with an average price of just $40.32. Plus, with over 6 customer reviews and an average rating of 4.5 stars, you can trust that our Moog Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from $38.99

(3)

Greaseable Super Strength Universal Joint

“Quality part”

from $44.99

(2)

Greaseable Super Strength Universal Joint

“Always there to get what you need!”

from $36.99

(1)

Greaseable Premium Universal Joint

“the u-joint itself fit fine however the grease fitting is too large for the hole provided in the u-joint. I had to enlarge the hole to fit the fitting”

Popular National 1963 Dodge D200 Series Drivetrains

National auto parts is one of the highest quality Drivetrain brands in the market. Any 1963 Dodge D200 Series owner should feel confident when installing genuine National parts in their vehicle. To ensure the best fit and performance for your 1963 D200 Series, Advance Auto Parts carries a full inventory of 3 National Drivetrains. Plus you will be keeping your Dodge in peak condition while saving money because prices on these National Drivetrains range from $17.99 to $38.99, plus, with more than 42 customer reviews and an impressive 4.3 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from $38.99

(2)

Tapered Roller Bearing Cone

“nice finish and function. Should perform well.”

from $22.99

(1)

Tapered Roller Bearing Cone

“So far so good.”

from $17.99

(39)

Multi-Purpose Bearing

“Great bearings”

FAQs for 1963 Dodge D200 Series Drivetrains

Which Drivetrains are best-sellers for 1963 Dodge D200 Series?

Out of 306 Drivetrains that fit 1963 Dodge D200 Series, the following parts are the top sellers:

Center Support Bearing Motor Mount: Center, 1 Piece (5300924) – $21.99
3 Qt – 80W90 Conventional Gear Oil With Posi Additive (11645418) – $57.99
3 Qt – Penzoil 80W90 Conventional Gear Oil (11644279) – $44.99

What’s the price range for 1963 Dodge D200 Series Drivetrains?

Drivetrain prices for the 1963 Dodge D200 Series start at $3.49 and go up to $1,566.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1963 Dodge D200 Series?

The average price for Drivetrains for the 1963 Dodge D200 Series is $243.55. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Dodge D200 Series model years?

Yes, we currently carry Drivetrains for 6 model years of Dodge D200 Series between 1960 and 1967. Drivetrains are bought most frequently for the following model years: 1967, 1966, 1965, 1964, 1962, 1961, and 1960.

What are the cheapest Drivetrains for my 1963 Dodge D200 Series?

The cheapest 1963 Dodge D200 Series Drivetrains we carry in stock are:

Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (21260547) – $3.49
Universal Joint (5270200) – $3.99
Dana 44 JK / 60 / 70U Pinion Nut Washer Replacement (11643194) – $3.99
Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (sold by each) (22149122) – $4.79
Replacement Ring Gear Bolt For Dana 60, 70, 70U & 70HD, 1/2" X 18 (11643357) – $4.99

What are the top-rated Drivetrains that fit the 1963 Dodge D200 Series?

Out of 214 reviews by customers, our 1963 Dodge D200 Series Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1963 Dodge D200 Series and their top-rated products:

Universal Joints
- Universal Joint (10265717) – $15.99
- Non-Greaseable Super Strength Universal Joint (10200043) – $29.99
- Greaseable Super Strength Universal Joint (10087213) – $38.99
Differentials
- Universal Joint (10265717) – $15.99
- Non-Greaseable Super Strength Universal Joint (10200043) – $29.99
- Greaseable Super Strength Universal Joint (10087213) – $38.99
Spindles
- Universal Joint (10265717) – $15.99
- Non-Greaseable Super Strength Universal Joint (10200043) – $29.99
- Greaseable Super Strength Universal Joint (10087213) – $38.99

What types of Drivetrains do you sell for my 1963 Dodge D200 Series?

As of 3/1/26, these are some of the most in-demand types of Drivetrains for a 1963 Dodge D200 Series:

Can I get help with 1963 Dodge D200 Series Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Dodge Drivetrains and more.

What is your return policy for Dodge D200 Series Drivetrains?

Advance Auto Parts keeps returns simple. For new Dodge D200 Series Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1963 Dodge D200 Series Drivetrains

Yukon Gear – Bolt/Screw For Adjuster Lock For Chrysler 7.25", 8.25", 8.75", 9.25" (Part No.33233)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)

Yukon Gear – Set Up Bearing (Part No.56041)

Yukon Gear – Zip Locker Bulkhead Fitting (Part No.34001)

Yukon Gear – Crush Sleeve Eliminator Kit For Chrysler 8.75" (Part No.55039)

Yukon Gear – Pinion Install Kit For Dana 60 Rear Differential (Part No.13032)

Yukon Gear – 7260 U/Joint Strap, Small Chrysler With Bolts, 7.25, 8.25, 8.75, 9.25 (Part No.41192)

Yukon Gear – Full-Floating, Blank 35 Spline Diameter, Non-Drilled Axle Shaft For Dana 60 (Part No.21005)

Yukon Gear – Replacement Yoke For Dana 44-HD, 60, And 70 With A 1310 U/Joint Size (Part No.41023)

National – Manual Transmission Input Shaft Seal (Part No.482163N)

Yukon Gear – Cross Pin Shaft For Standard Open Chrysler 9.25" (Part No.33311)

Yukon Gear – Powr Lok Button Kit For Dana 30, Dana 44 & Chrysler 8.75" (Part No.33536)

Yukon Gear – Positraction Clutch Guide (Part No.33352)

Yukon Gear – Chrysler 8.75" "89" Housing Nodular Iron Drop Out Case (Part No.32052)

Yukon Gear – Redi-Sleeve Yoke Saver For 8.75" C, 9.25" C, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD (Part No.30228)

Yukon Gear – Bearing Race Driver (Part No.56023)

Yukon Gear – Yoke For Chrysler 8.75" With 10 Spline Pinion And A 7260 U/Joint Size (Part No.41006)

Yukon Gear – High Performance Ring & Pinion Gear Set For ’09 & Down Chrysler 9.25" In A 3.55 Ratio (Part No.24013)

USA Standard Gear – Spartan Spring & Pin Kit, Fits Larger Designs (Part No.17010)

Yukon Gear – 3 Qt – Penzoil 80W90 Conventional Gear Oil (Part No.15002)

Yukon Gear – Standard Open Notched Cross Pin Shaft For 9.25" Chrysler (Part No.33309)

Dorman – Differential Pinion Yoke Assembly (Part No.697-544)

USA Standard Gear – Power Lok Positraction for Chrysler 8.75" (Part No.59027)

Dorman – Standard Spindle Nut 3/4 In.-16 Hex Size 1-1/16 In. (sold by each) (Part No.615-072)

Yukon Gear – Replacement Ring Gear Bolt For Dana 60, 70, 70U & 70HD, 1/2" X 18 (Part No.33037)

Yukon Gear – Chrome Replacement Cover For Dana 60 And 61 Standard Rotation (Part No.32005)

Motive Gear – Differential Pinion Shim Kit (Part No.1118)

Yukon Gear – Chrysler 8.75" (Coarse Spline) Pinion Nut Washer (Part No.33162)

Driveworks – Universal Joint (Part No.DW-316)

Driveworks – Universal Joint (Part No.DW-315G)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.246)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.248)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.317)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.318-10)

MOOG Driveline Products – Non-Greaseable Super Strength Universal Joint (Part No.245)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.316)

MOOG Driveline Products – Greaseable Premium Universal Joint (Part No.315G)

Spicer – Universal Joint (Part No.5-811X)

MOOG Driveline Products – Universal Joint Strap Kit (Part No.316-10)

Spicer – Universal Joint (Part No.5-789X)

Yukon Gear – 1310 To 1330 Adapter U/Joint (Part No.42005)

Yukon Gear – Dana 44, 8.2", 12P, 12T, Vet, And Model 20 U-Bolts (Part No.41198)

Yukon Gear – 1350 & 1410 U/Joint U-Bolts, 3/8" X 1-11/16", Kit (Part No.41190)

Yukon Gear – 1350 To 1410 Conversion U/Joint (Part No.42006)

Yukon Gear – 1310 To Mechanics 3R Adapter U/Joint (Part No.42013)

Yukon Gear – 1350 Lifetime Series U/Joint (Part No.42021)

Yukon Gear – 1330 Dual-Size Cap U/Joint (Part No.42017)

Yukon Gear – 7290 U/Joint Strap Kit (4 Bolts And 2 Straps) For Chrysler 7.25", 8.25", 8.75", And 9.25" (Part No.41013)

Yukon Gear – 1350 U/Joint With Zerk Fitting (Part No.42010)

Yukon Gear – 1330 Lifetime U/Joint (Part No.42004)

Yukon Gear – 1330 U/Joint With Zerk Fitting (Part No.42002)

Yukon Gear – 1310 Lifetime U/Joint (Part No.42003)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6038)

National – Multi-Purpose Bearing (Part No.A-5)

National – Drive Shaft Center Support Bearing (Part No.HB-88107-A)

Anchor – Center Support Bearing Motor Mount: Center, 1 Piece (Part No.6056)

National – Multi-Purpose Bearing (Part No.205)

Yukon Gear – 8.75" Chrysler Inner Axle Seal, Use With Set7 (Part No.30198)

Yukon Gear – 8.75" Chrysler Outer Axle Seal, Use With Set7 (Part No.30199)

National – Shaft Repair Sleeve (Part No.99125)

Yukon Gear – Pinion Yoke Dust Shield For Dana 60 & 70 (Part No.33441)

National – Multi-Purpose Bearing (Part No.88107-BVV)

Yukon Gear – Fill Plug For Chrysler 8.75", 3/4" Thread (Part No.33462)

Yukon Gear – Billet Replacement Yoke For Dana 60 And 70 With 29 Spline Pinion And A 1350 U/Joint Size (Part No.41138)

Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1330 U/Joint Size (Part No.41025)

Yukon Gear – Yoke For Chrysler 8.75" With 10 Spline Pinion And A 7290 U/Joint Size (Part No.41130)

Yukon Gear – Replacement Yoke For Dana 44-HD, 60, And 70 With A 1310 U/Joint Size (Part No.41022)

Yukon Gear – Replacement Yoke For Dana 60 And 70 With A 1350 U/Joint Size (Part No.41027)

Yukon Gear – Yoke For Chrysler 8.75" With 10 Spline Pinion And A 7260 U/Joint Size (Part No.41006)

Yukon Gear – Yoke For Chrysler 8.75" With 29 Spline Pinion And A 7260 U/Joint Size (Part No.41007)

Spicer – Drive Shaft Center Support Bearing (Part No.210088-1X)

Spicer – Drive Shaft Center Support Bearing (Part No.210090-1X)

National – Tapered Roller Bearing Cone (Part No.HM89443)

Felpro – Differential Carrier Gasket Round Shaped 10 Bolt Hole Gasket (Part No.RDS 6583)

National – Tapered Roller Bearing Cone (Part No.368A)

Yukon Gear – 3 Qt – 80W90 Conventional Gear Oil With Posi Additive (Part No.15003)

Yukon Gear – 3 Qt – Penzoil 80W90 Conventional Gear Oil (Part No.15002)

Yukon Gear – Dana 60, Dana 70 & Dana 80 Cover Bolt (Part No.33235)

Yukon Gear – Replacement Ring Gear Bolt For Dana 60, 70, 70U & 70HD, 1/2" X 18 (Part No.33037)