1963 Chrysler Imperial Differentials

Product Features:

• CRUSH SLEEVE 7.25 & 8.25 MIN ORDER 5000

Yukon 1541H alloy right hand rear axle for Model 35 (drum brakes) with a 54 tooth, 2.7″ ABS ring. axle has a length of 29-1/4″ inches and 27 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H allo

Product Features:

• Pinion depth shims for AMC Model 35 and Chrysler 7.25″

Product Features:

• CHRY 8 3/4″ RING GEAR BOLTS C 8.25″

9.25″ pinion gear thrust washer.

Product Features:

• Pinion gear thrust washer for Chrysler 9.25″ rear

Yukon yoke for Chrysler 9.25″ with a 7260 U/joint size. 2.125″ snap ring span, 1.078″ cap diameter. Inside snap ring.All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Chrysler 9.25″ rear
• 29 spline
• 7260 u-joint size
• Inside snap ring design
• 2.125″ snap ring span
• 1.078″ cap diameter
• Strap style

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits 1976-2004 Chrysler 8.25″
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits 1975 and down Chrysler 8.25″
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M88010 race
• All steel construction

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

• Redi-Sleeve yoke saver
• Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

Product Features:

• BILLET HP 1350-29 SPLINE YOKE

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

• Powr Lok button kit
• Fits Dana Spicer 30, 44 and Chrysler 8.75″

Pinion nut for Chrysler 7.25″, 8.0″ IFS, 8.25″, 8.75″ fine spline, 9.25″ front & rear, 7/16″ x 14.

Product Features:

• Pinion nut for Chrysler 8.0″ IFS, 8.25″, 8.75″ with 29 spline pinion and 9.25″ rear
• 7/8″ x 14 thread

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits Chrysler 8.25″ with 29 spline axles
• Made from 9310 steel for added strength
• Replaces the spiders in a standard carrier case

Product Features:

• CHRY 10BLT 8.25+8.36 R&P-3.55 RATIO

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits Chrysler 8.75″ ’89’ case housing with LM104912 carrier races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.

Chrysler 8.75″ (coarse spline) pinion nut washer.

Product Features:

• Pinion nut washer
• Fits Chrysler 8.75″ with 10 spline pinion

Dana 44 & 9.25 Chrysler TracLoc clutch kit.

Product Features:

• Clutch kit
• Fits Dana Spicer 44 and Chrysler 9.25″ Trac Loc positraction

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Design type: spring loaded; multi-lip
• Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
• Resistance to EP lubricants
• Low swell in hydrocarbon fluids
• Delivers quality and reliable performance for every type of repair

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Bolt/screw for adjuster lock for Chrysler 7.25″, 8.25″, 8.75″, 9.25″.

Product Features:

• Side adjuster lock bolt
• Fits Chrysler 7.25″, 8.25″, 8.75″ and 9.25″

Spartan spring & pin kit, fits smaller designs.

Product Features:

• Replacement spring and pin kit for Spartan Locker
• Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
• Includes 4 springs and 4 alignment pins

8.25″ Chrysler notched cross pin shaft for standard open carriers. (0.801″ diameter). This cross pin shaft is not compatible with Powertrax Lock Rights or Spartan Lockers, or with factory Trac Loc positractions.

Product Features:

• Cross pin shaft
• Fits Chryler 8.25″
• 0.801″ diameter
• Notched
• Not compatible with Spartan Lockers or Lock Rights