1961 Dodge Phoenix Performance and Racing Products
More 1961 Dodge Phoenix Performance and Racing Products Categories
If you’re looking for an original Performance and Racing Products replacement for a 1961 Dodge Phoenix, you can search through our selection below. You’ll also find aftermarket and OEM Performance and Racing Products to meet your needs.
Essential 1961 Dodge Phoenix Performance and Racing Products
Edelbrock – Performer Carburetor #9913 750 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No.9913)
from
$427.99
Product Features:
See More
- Satin Finish
- 4 Barrel
- Annular Booster Type
- Electric Choke Type
- 750 cfm Maximum Flow Rating
Fram – High Perf. Full-Flow Lube Spin-on (Part No.HP1)
from
$16.99
FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.**
Product Features:
See More
Product Features:
- Proven protection for up to 10,000 miles
- Engineered for use with synthetic or conventional motor oils
- Filter media is a blend of fiber and resin that captures 95% of the dirt particles
- The perfect balance of dirt-trapping efficiency and dirt-holding capacity
FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1432)
from
$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
- Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
- Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
- Slotted bolt holes allow for easier header installation.
- Not intended for use in emission controlled vehicles.
Edelbrock – Sure Seat Valve Springs for Chrysler 318-340-360 V8 1957-89 (Part No.5877)
from
$59.99
Product Features:
See More
- Non-Rotator Type
- 1.394 in. Outer Diameter
- 1.010 in. Inner Diameter
- 1.010 in. Coil Blind
- Set of 16
FEL-PRO Performance – Lower Intake Manifold Gasket Set: 6 Piece Set (Part No.1213)
from
$36.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
- ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Mallory – Distributor Wiring Harness (Part No.29349)
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1008)
from
$41.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
- Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
- Raises combustion sealing force to roughly three times that of standard head gaskets.
- Steel wire rings for the greatest combustion seal strength.
- Not intended for use in emission controlled vehicles.
K&N – Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration (Part No.E-1100)
from
$102.99
K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle or outdoor power small engine. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.
Product Features:
See More
Product Features:
- ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
- RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
- 4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
- CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
- ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
- EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
- ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
- MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability
Edelbrock – Big-Block Chrysler E-Street Cylinder Heads 84cc (Part No.5093)
from
$2198.99
The Edelbrock #5093 E-Street cylinder heads are designed for use with 1961-1979 Chrysler 361-440 c.i.d. Wedge engine applications. The Edelbrock E-Street cylinder heads offer American made quality and affordable performance. E-Street cylinder heads featur
Product Features:
See More
Product Features:
- Complete Pair For Hydraulic Flat Tappet
- 84cc Combustion Chamber Volume
- 210cc Intake/70cc Exhaust Runner Volume
- 2.14 in. Intake/1.81 in. Exhaust Valve Diameter
- 0.625 in. Deck Thickness
FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1806)
from
$21.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
- With steel core to provide ultimate excellent blowout resistance.
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – PERFORMANCE VALVE COVER GASKET SET (Part No.1608)
from
$37.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- ENGINEERED TO PERFORM — Proprietary cork-rubber formulation
- SUPERIOR SEAL — Highly conformable to accommodate for the imperfect sealing surfaces
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
- REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
Edelbrock – RPM Air-Gap Small Block Chrysler Black Intake Manifold (Part No.75763)
from
$612.99
Edelbrock part #75763 RPM Air-Gap intake manifold is designed for 340-360 c.i.d. Chrysler V8’s and 318 c.i.d. engines with 340-360 cylinder heads. The RPM Air-Gap incorporates the same race-winning technology that’s been used on our Victor Series competit
Product Features:
See More
Product Features:
- 1500-6500 RPM Range
- Dual Plane Type-4150 Style Flange
- 4.9 in. Front Height, 5.35 in. Center Height, 5.8 in. Rear Height
- Black Powder Coated Finish
- Made In The USA
Hurst – B-1 Shifter Boot and Plate (Part No.1147336)
from
$42.49
Designed for use with round stick shifters. Complete with chrome ID plate and mounting hardware. Measures: 4-3/8 in. x 5-3/8 in. with 3 pleats.
Product Features:
See More
Product Features:
- Complete with Mounting Hardware
- Adapt To Most Shifter Install
- Hurst Quality
- Works Well with Round Shift Levers
- Chrome ID Plate
Energy Suspension – Sway Bar Bushing Set (Part No.5.5113G)
from
$16.99
Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.
Product Features:
See More
Product Features:
- Allows Sway Bar System to Work At 100% Efficiency
- Zerk Type Fittings
- Allows for Periodic Greasing
- Lasts Much Longer Than OEM Rubber Bushings
- Handling Characteristics Improve Dramatically
FEL-PRO Performance – Engine Crankshaft Seal Kit (Part No.2947)
from
$48.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fluoroelastomer compound combines optimum resistance to heat, oils and abrasion for longivity.
- Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Intake Manifold Bolts (Part No.6091)
from
$32.09
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.
Product Features:
See More
Product Features:
- Features 12-point Smaller-than-standard Bolt Head
- Thick Flat Washers Distribute Optimum Clamp Load
- Ideal Use Where Space Is Minimal On Race Manifolds
- Bolts And Washers Zinc Plated For Protection
- Zinc Plated For Protection
Energy Suspension – Sway Bar Bushing Set (Part No.5.5115G)
from
$16.99
Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.
Product Features:
See More
Product Features:
- Allows Sway Bar System to Work At 100% Efficiency
- Zerk Type Fittings
- Allows for Periodic Greasing
- Lasts Much Longer Than OEM Rubber Bushings
- Handling Characteristics Improve Dramatically
Energy Suspension – Sway Bar Bushing Set (Part No.5.5113R)
from
$16.99
Energy Suspension performance polyurethane sway bar bushings and end links offer the greatest improvement in performance among all the products Energy offers. They make a vehicle’s sway bar system much more effective like adding a larger, higher performance sway bar! Economy, increased efficiency, and easy installation are just some of the reasons these products are so popular. Made of Hyper-Flex polyurethane that lasts much longer than O.E.M. rubber bushings.
Product Features:
See More
Product Features:
- Allows Sway Bar System to Work At 100% Efficiency
- Zerk Type Fittings
- Allows for Periodic Greasing
- Lasts Much Longer Than OEM Rubber Bushings
- Handling Characteristics Improve Dramatically
Competition Cams – High Energy 218/218 Hydraulic Flat Cam and Lifter Kit for Chrysler 383-440 (Part No.CL21-215-4)
from
$1499.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering
Product Features:
See More
Product Features:
- Good blend of efficiency and performance.
- Perfect choice for performance street rebuilds.
- Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
Competition Cams – Xtreme Energy 224/230 Hydraulic Flat Cam K-Kit for Chrysler 383-440 (Part No.K21-223-4)
from
$645.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,
Product Features:
See More
Product Features:
- Excellent performance in street carbureted applications.
- More vacuum allows an increase in duration for improved performance and assists power brakes.
- Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
- Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
Earls Performance Product – Solo Bleed (Part No.280021ERL)
from
$32.59Product Features:
- Prevents Air Inclusion
- Direct Replacement
- For OE Bleeders
- One Person Bleeds Safely
- Without The Mess
- No Chance Of Air Bubbles
Energy Suspension – Control Arm Bushing Set (Part No.5.3132R)
from
$62.99
For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.
Product Features:
See More
Product Features:
- Maintains Better Alignment While Driving
- Full Floating and Non Binding
- Fits Into the Remaining Stock Control Arms
Lakewood – Drag Shock-70/30:Ford/GM/Mopar (Part No.40121)
from
$104.99
The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.
Product Features:
See More
Product Features:
- Excellent Weight Transfer
- Lets Front End Down Quickly
- Maximum Traction
- Makes Vehicle Safer
- Easier Control At End Of Track
- Better Overall Stability
Edelbrock – Performer RPM Series fuel pump is for Small-Block Chrysler (Part No.1720)
from
$209.99
Edelbrock part #1720 Performer RPM Series fuel pump is for Small-Block Chrysler designed for use with all Edelbrock carburetors used in Performer or Performer RPM applications. These high-performance’s street Fuel Pumps feature a high quality three stage
See More
Popular 1961 Dodge Phoenix Performance and Racing Products Categories
1961 Dodge Phoenix Performance and Racing Products
You count on your 1961 Dodge Phoenix to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 50 Performance and Racing Products ranging in price from $16.99 to $2,198.99, you’re sure to find everything you need for your 1961 Dodge Phoenix.
Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 13 different brands like K&N, Edelbrock, and FEL-PRO Performance. 1961 Dodge Phoenix Performance and Racing Products start as low as $16.99!
One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 273 extensive product reviews on 1961 Dodge Phoenix Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Intake Manifold Bolts with 4.6 stars and Performer Carburetor #9906 600 CFM With Electric Choke, Satin Finish (Non-EGR) with 3.8 stars.
Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1961 Dodge Phoenix below to get started!
Top-Rated Performance and Racing Products Brands For Your 1961 Dodge Phoenix
Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1961 Dodge Phoenix running right for years to come. In our inventory you’ll find brands like K&N, Edelbrock, FEL-PRO Performance, and even more.
Popular Mallory Performance and Racing Products
You’ll find popular Mallory brand products across Performance Ignition Products. All are waiting to get your 1961 Dodge Phoenix back on the road. Some of the top-rated Mallory products in these categories are:
Top-Rated K&N Performance and Racing Products
If K&N are what you’re looking for, our inventory holds plenty. We stock K&N brand Performance and Racing Products for your 1961 Dodge Phoenix, and some of our most reviewed K&N parts include:
from
$17.99
(120)
Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine
Performance Oil Filters
from
$102.99
(5)
Engine Air Filter: Washable Filter, Increase Horsepower & Acceleration
Performance Air Filters
FAQs for 1961 Dodge Phoenix Performance and Racing Products
What are the most purchased Performance and Racing Products for the 1961 Dodge Phoenix?
Out of 50 Performance and Racing Products for the 1961 Dodge Phoenix, the most popular in our inventory are:
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Performance Carburetors
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
Performance Carburetors
What are the top-rated 1961 Dodge Phoenix Performance and Racing Products?
Top-rated Performance and Racing Products for your 1961 Dodge Phoenix based on customer reviews/ratings are:
from
$397.99
(5)
Performer Carburetor #9906 600 CFM With Electric Choke, Satin Finish (Non-EGR)
“easy to install all the gaskets and parts came with it”
