1961 Chevrolet Impala Air Intakes
More 1961 Chevrolet Impala Air Intakes Categories
If you’re looking for an original Air Intakes replacement for a 1961 Chevrolet Impala, you can search through our selection below. You’ll also find aftermarket and OEM Air Intakes to meet your needs.
Essential 1961 Chevrolet Impala Air Intakes
Edelbrock – Carburetor Progressive Throttle Linkage Kit for Triple Carb Set-up (Part No.1033)
from
$186.99
The Edelbrock part #1033 Progressive Linkage Kit is designed to smooth throttle response, eliminate flat spots and improve fuel economy. It achieves this by only opening the center carburetor at less than 50% (or 33%) pedal travel thus sharpening the vent
Product Features:
See More
Product Features:
- Steel Material
- Zinc Plated
- Adjustable
- 3-Barrel Configuration
- Made In The USA
Edelbrock – Standard Flow Carburetor Power Valve #12645 Single Stage 4.5in Hg (Part No.12645)
from
$16.99
Product Features:
See More
- The Edelbrock #12645 Single Stage 4.5 Hg Power Valve operates by using engine vacuum to control the opening and closing rate.
- During heavy load or under full power situations, they open to supply additional fuel to the main system to eliminate hesitation and bogging, ensuring the smooth delivery of power without any drivability concerns.
Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)
from
$24.99
The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.
Product Features:
See More
Product Features:
- Steel Material
- For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
- Includes Lightest To Heavy
- Set of 7
- Made in The USA
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$12.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Edelbrock – Pro-Flo 1000 Series Chrome Air Cleaner with Foam Element with 5-1/8" Air Horn (Part No.1002)
from
$31.99Product Features:
- Super Flow; Good Filtration
- Urethane Foam Element
- Strong Metal Inner Frame
- Performance Benefits
- Cleans With Soap and Water
- Low Maintenance Cost
- Simple To Install
- Nicely Finished; Low Profile
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$43.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
ARP Auto Racing – For Use With Chevy 396/ 454 Cubic Inch, Hex Head, Polished, Ss, With Washers (Part No.435-2001)
from
$59.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 Psi Tensile Strength
- Precision Machined Threads For Secure Engagement, And Would not Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
ARP Auto Racing – For Use With Chevy 396/ 454 Cubic", 12 Point Head Type, Polished, With Washers (Part No.435-2101)
from
$59.99
Prevent intake manifold leaks with ARP quality fasteners. They are rated at 170,000 PSI and precision machined for optimum thread engagement. Wide under head flange and companion washers provide even load distribution. Precision rolled threads prevent galling while promoting more consistent torque loading. Facilitates optimum sealing of gasket surfaces. Available in choice of black oxide finish chrome moly or corrosion resistant stainless steel, as well as hex or 12 point heads.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Precision Machined Threads For Secure Engagement, And Wont Rust
- Wide Under Head Flange And Companion Washers Provide Even Load Distribution
- Precision Rolled Threads Prevent Galling While Promoting More Consistent Torque Loading
- Facilitates Optimum Sealing Of Gasket Surfaces
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$40.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Felpro – AIR CLEANER MOUNTING GASKET (Part No.60357)
from
$2.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific, providing unsurpassed quality for a seal you can trust
- Validated for fit, form, and function
- Engineered for the sealing repair environment
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Air Cleaner Mounting Gasket (Part No.11528)
from
$2.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific, providing unsurpassed quality for a seal you can trust
- Validated for fit, form, and function
- Engineered for the sealing repair environment
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Edelbrock – Performer EPS Intake Manifold for 1955-86 Small-Block Chevy, Black Finish (Part No.27013)
from
$360.99
Edelbrock part #27013 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thr
Product Features:
See More
Product Features:
- Idle-5500 RPM Range
- Dual Plane Type-4150 Style Flange
- 3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
- Black Powder Coated Finish
- Non-EGR
Edelbrock – Performer RPM AIR-Gap Small Block Chevy Black Intake Manifold (Part No.75013)
from
$525.99
Edelbrock part #75013 RPM Air-Gap RPM intake manifold is designed for 1955-86 262-400 c.i.d. Chevrolet V8’s. The award-winning RPM Air-Gap intake manifold incorporates the same race-winning technology that’s used on our Victor Series competition intakes.
Product Features:
See More
Product Features:
- 1500-6500 RPM Range
- Dual Plane Type-4150 Style Flange
- 4.2 in. Front Height, 4.72 in. Center Height, 5.25 in. Rear Height
- Black Powder Coated Finish
- Non-EGR
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$13.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Edelbrock – Standard Main Jet Carburetor Metering Jet #12458 Size .057 (Pair) (Part No.12458)
from
$13.99
The Edelbrock 94 #12458 Carburetor Jets .058″Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 58 Maximum Jet Size
- 0.057 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Felpro – Carburetor Mounting Gasket (Part No.60482)
from
$16.29
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Felpro – Carburetor Mounting Gasket (Part No.60148)
from
$4.49
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
United Carb – Remanufactured Carburetor 2 Barrel (Part No.3-3398)
from
$250.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More
United Carb – Remanufactured Carburetor 4 Barrel (Part No.3-3175)
from
$307.99
Made in the USA, this remanufactured carburetor is completely disassembled and all internal parts, such as gaskets, gas filters, needle/seats and accelerator plunger cups, are discarded. All metal castings are thoroughly cleaned and restored to OEM (original equipment manufacturer) finish. Then the carburetor is reassembled to OEM-quality standards using all new component parts. Each carburetor is flow tested to simulate actual engine conditions, and all internal and external adjustments are set to OEM specifications.
See More
Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1775)
from
$32.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
See More
Wells Vehicle Electronics – Carburetor Tune-Up Kit (Part No.2G1781)
from
$35.99
WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to OE designs. Every component either matches or improves on the OE design to ensure fast, easy installation, superior performance and reliability.
See More
Edelbrock – Triple Carburetor Fuel Log Kit #1288 with 5-1/2 in. Outlet Spacing (Part No.1288)
from
$99.99
This Edelbrock Fuel Log kit #1284 is an exact replica of the original design used by Vic Sr. in the 1950’s. They are made from extruded aluminum tube with a 3/8″ threaded outlet at each end and a polished finish. Kit includes, black neoprene hose, Corbin
Product Features:
See More
Product Features:
- Polished Log
- Brass Fittings
- Black Neoprene Hose
- 5-1/2 in. Outlet Spacing
- Includes Hose Clamps
Felpro – INTAKE MANIFOLD GASKET SET (Part No.MIK 98015 T)
from
$159.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
- Application specific design to ensure a perfect fit
- Meets or exceeds all original equipment specifications
- Engineered and manufactured specifically for repair applications
- Unsurpassed quality you can trust
- Included all parts needed to complete the repair
- Included all parts needed to complete the repair
Felpro – Engine Intake Manifold Gasket Set (Part No.MS 98015 T)
from
$151.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
- STRONG AND DURABLE — Features molded rubber over an aluminized steel carrier which resists high heat and coolants
- SUPERIOR SEAL — Proprietary rubber sealing beads help eliminate potential leak paths for a superior seal
- EASIER TO INSTALL — Locating tabs assure proper alignment and easier installation
- PREVENTS OVERTIGHTENING — Torque limiters help eliminate overtightening and gasket splitting and extruding
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
- EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
Edelbrock – Intake Manifold Gasket for 1965-1990, Oval port 396-402-454 B/B Chevy (Part No.7203)
from
$32.99
Product Features:
See More
- Clean Positive Seal
- Embossed Silicone Bead Surrounding The Port
- Matched To Manifolds And Cylinder Heads
Carquest – Needle and Seat (Part No.93-554R)
from
$9.49
High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.
Product Features:
See More
Product Features:
- Designed to OE standards for ease of installation
Edelbrock – Non-Adjustable Carburetor Needle and Seat #12605 Size .110 With Viton Tip (Part No.12605)
from
$20.99
The Edelbrock #12605 Non-Adjustable Inlet Needle and Seat assembly will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 23
Product Features:
See More
Product Features:
- Center Hung Floats
- 0.11 in. Needle Diameter
- Viton® Needle Material
- Sold Individually
- Non-Adjustable Type
Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)
from
$18.99
Product Features:
See More
- The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
- Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
Popular 1961 Chevrolet Impala Air Intakes Categories
1961 Chevrolet Impala Air Intakes
You count on your 1961 Chevrolet Impala to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Air Intakes. With 80 Air Intakes ranging in price from $1.99 to $1,776.99, you’re sure to find everything you need for your 1961 Chevrolet Impala.
Brands matter. If you want to shop a specific Air Intakes brand, we stock 8 different brands like Felpro, Edelbrock, and Mr. Gasket. 1961 Chevrolet Impala Air Intakes start as low as $1.99!
One of the best ways to find top quality OEM or aftermarket Air Intakes is by asking professionals. Short of that, you can shop with confidence thanks to our 316 extensive product reviews on 1961 Chevrolet Impala Air Intakes. Some of the top-rated Air Intakes products we carry are Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet with 4.4 stars and Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs with 4.5 stars.
Did we mention you can order your Air Intakes from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Air Intakes inventory for your 1961 Chevrolet Impala below to get started!
Top-Rated Air Intakes Brands For Your 1961 Chevrolet Impala
Trusted Air Intakes OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1961 Chevrolet Impala running right for years to come. In our inventory you’ll find brands like Felpro, Edelbrock, Mr. Gasket, and even more.
Popular Holley Air Intakes
You’ll find popular Holley brand products across Intake Manifold Parts. All are waiting to get your 1961 Chevrolet Impala back on the road. Some of the top-rated Holley products in these categories are:
Top-Rated Edelbrock Air Intakes
If Edelbrock are what you’re looking for, our inventory holds plenty. We stock Edelbrock brand Air Intakes for your 1961 Chevrolet Impala, and some of our most reviewed Edelbrock parts include:
from
$16.99
(27)
Standard Flow Carburetor Power Valve #12625 Single Stage 2.5in Hg
Carburetor Power Valves
from
$43.99
(19)
Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange)
Air Cleaner Assemblies
from
$31.99
(10)
Pro-Flo 1000 Series Chrome Air Cleaner with Foam Element with 5-1/8" Air Horn
Air Cleaner Assemblies
FAQs for 1961 Chevrolet Impala Air Intakes
What are the most purchased Air Intakes for the 1961 Chevrolet Impala?
Out of 80 Air Intakes for the 1961 Chevrolet Impala, the most popular in our inventory are:
from
$47.99
(9)
Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange)
Air Cleaner Assemblies
What are the top-rated 1961 Chevrolet Impala Air Intakes?
Top-rated Air Intakes for your 1961 Chevrolet Impala based on customer reviews/ratings are:
from
$451.99
(7)
Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“Easy install, had it installed in less then 30 mins on my 70 camaro 350 after my holley failed. It started right up only adjustment i had to do was tu”
from
$14.99
(4)
Carburetor Gasket Kit #12382 Fits 2300, 4150, 4160, 4175, And 4500 Carburetors
“Was the wrong slip joint. Catalog was very confusing to use and misleading. Had to locate through another website.”
