1961 Chevrolet Bel Air Drivetrains
More 1961 Chevrolet Bel Air Drivetrains Categories
If you’re looking for an original Drivetrains replacement for a 1961 Chevrolet Bel Air, you can search through our selection below. You’ll also find aftermarket and OEM Drivetrains to meet your needs.
Essential 1961 Chevrolet Bel Air Drivetrains
Yukon Gear – Spider Gear Kit (Part No.16050)
from
$612.99
Yukon spider gear set for GM 8.2″ Dura Grip posi, 28 spline. This kit does not include clutches. This kit fits Yukon Dura Grip ONLY.
Product Features:
See More
Product Features:
- Spider gear kit
- Fits GM 8.2″ with Dura Grip positraction
- Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.
National – Multi Purpose Bearing (Part No.HB-206-FF)
from
$46.49
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Controlled heat treating process for lasting performance and extended bearing life
- Industry leading coverage
- Professional technicians know they can depend on National
Driveworks – Universal Joint (Part No.DW-369)
from
$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).
Product Features:
See More
Product Features:
- The cross is hot forged for the higher torque and horsepower
- The bearing cups are made by cold forging, having higher strength and better rigidity
- Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
- Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
- Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
- Snap rings are held to strict tolerances to ensure proper cup position and retention
- Nitrile rubber seals to optimize grease retention and reduce contamination
Motive Gear – Differential Crush Sleeve (Part No.3110)
Yukon Gear – Mini Spool For GM 8.5" With 30 Spline Axles (Part No.32233)
from
$188.99
Mini spools are a low-cost traction option for vehicles looking for full-time lockup. The mini spool installs into a standard open carrier and give 100% power to both tires at all times. These units are not recommended for street-driven vehicles. We recommend full spools for vehicles with large tires or high horsepower. These units come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits GM 8.5″ with 30 spline axles
- Installs into a standard open carrier case
- Provides 100% traction to both wheels at all times
- Not recommended for street driven vehicles
Yukon Gear – Bearing Race Driver (Part No.56017)
from
$215.99
Bearing race driver. No return.
Product Features:
See More
Product Features:
- Bearing race driver
- Fits HM89410 race
- All steel construction
Yukon Gear – Pinion Install Kit For GM 8.5" Differential (Part No.13069)
from
$173.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.
Product Features:
See More
Product Features:
- Fits GM 8.5″ rear
- Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.
Yukon Gear – 8.2" GM & CI Vette Positraction Cross Pin Shaft (Part No.33411)
from
$73.99
8.2″ GM & CI Vette positraction cross pin shaft.
Product Features:
See More
Product Features:
- Cross pin shaft for GM 8.2″ and 1963-1979 Corvette
- Fits standard open and positraction applications
MOOG Driveline Products – Universal Joint U-Bolt Kit (Part No.329-10)
from
$9.99
By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.
Product Features:
See More
Product Features:
- For U-Joints 353, 354, 361, 369 & 497
- Fits 1-1/16″ bearings
National – Shaft Repair Sleeve (Part No.99170)
from
$41.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
- Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
Yukon Gear – 55-56 Corvette Axle Kit, Left Hand & Right Hand, 17Spline (Part No.21637)
from
$719.99
55-56 Corvette axle kit, left hand & Right hand, 17spline.
Product Features:
See More
Product Features:
- 17 spline
- Fits 1955-1956 Corvette
- Includes two axles
National – Multi Purpose Seal (Part No.5200)
from
$12.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Low swell in hydrocarbon fluids
- Design type: spring loaded; multi-lip
- Provides good low temperature capability
- Temperature range: -40°F to 225°F; -40°C to 107°C
- Delivers quality and reliable performance for every type of repair
Yukon Gear – Dana 44 Pinion Gear Thrust Washer (Part No.33281)
from
$4.99
Dana 44, GM55P & 8.2″ GM pinion gear Thrust washer.
Product Features:
See More
Product Features:
- Pinion gear thrust washer for Dana Spicer 44, GM 8.2″ and 1955-1964 GM passenger car
Richmond Gear – RngPnn (Part No.79-0072-1)
from
$513.99
RngPnn
Felpro – Differential Carrier Gasket (Part No.RDS 5008)
from
$5.79
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Unsurpassed quality you can trust
- Validated for fit, form and function
- Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes
Driveworks – Tapered Roller Bearing (Part No.S-M-802011)
Driveworks – Oil Seal (Part No.S-7412S)
from
$6.79
Value-priced seal meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
Yukon Gear – Dana 30 & Dana 44 Power Lok Bolt, Left Hand, & 8.75" Chrysler & 55P (Part No.33234)
from
$26.99
Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.
Product Features:
See More
Product Features:
- Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
- Left hand thread
National – Bearings (Part No.LM603014)
from
$20.79
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Driveworks – Ball Bearing (Part No.S-206-FF)
Yukon Gear – Pinion Depth Shims For GM 7.5", 7.75", 8.2" & 12 Bolt Truck (Part No.55008)
from
$21.99
Product Features:
See More
- Pinion depth shims for GM 7.5″, 7.625″, 7.6 IFS, 7.6 IRS, 7.75″, 8.2″, 1955-1964 passenger car and 12 bolt car and truck
National – Bearings (Part No.HM88510)
from
$14.29
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Powertrax – No-Slip Traction System (Part No.9207853005)
from
$544.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles. Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction. Powertrax® = Extreme Traction Systems!
See More
Yukon Gear – Yoke For GM 55P And 55T With A 1310 U/Joint Size (Part No.41089)
from
$319.99
Yukon yoke for GM 55P and 55T with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits 1955-1964 GM passenger car and truck
- 17 spline
- 1310 u-joint size
- Outside snap ring design
- 3.219″ snap ring span
- 1.062″ cap diameter
- Strap style
National – Bearings (Part No.M86649)
from
$18.79
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.
Product Features:
See More
Product Features:
- Premium bearing design matches OEM specifications
- Precision manufactured using premium-grade steel for outstanding durability and performance
- Crowned raceways and rollers to ensure even load distribution for maximum life
- Industry leading coverage
- Professional technicians know they can depend on National
Powertrax – Grip LS Traction System (Part No.LS231230)
from
$480.99
For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!
See More
Yukon Gear – Minor Install Kit For GM 8.5" Rear Differential (Part No.12055)
from
$48.99
Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush. (includes Supershims)
Product Features:
See More
Product Features:
- Fits GM 8.5″ rear
- Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.
Yukon Gear – 8.75" Chrysler & 55P Chevy Power Lok Clutches, Model 20 Also, Posi (Part No.16148)
from
$275.99
8.75″ Chrysler & 55P Chevy Power Lok clutches, Model 20 also, POSI.
Product Features:
See More
Product Features:
- Clutch kit
- Fits Chrysler 8.75″, 1955-1964 GM passenger car and AMC Model 20 Powr Lok positraction
Popular 1961 Chevrolet Bel Air Drivetrains Categories
1961 Chevrolet Bel Air Drivetrains
You count on your 1961 Chevrolet Bel Air to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Drivetrains. With 86 Drivetrains ranging in price from $4.49 to $883.99, you’re sure to find everything you need for your 1961 Chevrolet Bel Air.
Brands matter. If you want to shop a specific Drivetrains brand, we stock 14 different brands like Valvoline, Moog, and Driveworks. 1961 Chevrolet Bel Air Drivetrains start as low as $4.49!
One of the best ways to find top quality OEM or aftermarket Drivetrains is by asking professionals. Short of that, you can shop with confidence thanks to our 2,896 extensive product reviews on 1961 Chevrolet Bel Air Drivetrains. Some of the top-rated Drivetrains products we carry are Greaseable Super Strength Universal Joint with 4.6 stars and Non-Greaseable Super Strength Universal Joint with 4.3 stars.
Did we mention you can order your Drivetrains from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Drivetrains inventory for your 1961 Chevrolet Bel Air below to get started!
Top-Rated Drivetrains Brands For Your 1961 Chevrolet Bel Air
Trusted Drivetrains OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1961 Chevrolet Bel Air running right for years to come. In our inventory you’ll find brands like Valvoline, Moog, Driveworks, and even more.
Popular Felpro Drivetrains
You’ll find popular Felpro brand products across Differentials. All are waiting to get your 1961 Chevrolet Bel Air back on the road. Some of the top-rated Felpro products in these categories are:
Top-Rated Drivetrains
If are what you’re looking for, our inventory holds plenty. We stock brand Drivetrains for your 1961 Chevrolet Bel Air, and some of our most reviewed parts include:
from
$12.79
(446)
MaxLife Multi-Vehicle (ATF) Full Synthetic Automatic Transmission Fluid, 1 Quart
Differential Oil
FAQs for 1961 Chevrolet Bel Air Drivetrains
What are the most purchased Drivetrains for the 1961 Chevrolet Bel Air?
Out of 86 Drivetrains for the 1961 Chevrolet Bel Air, the most popular in our inventory are:
What are the top-rated 1961 Chevrolet Bel Air Drivetrains?
Top-rated Drivetrains for your 1961 Chevrolet Bel Air based on customer reviews/ratings are:
from
$32.99
(37)
Greaseable Super Strength Universal Joint
“grease fitting I like location dont like needle design to grease should be regular design fitting”
