1960 Pontiac Ventura Performance and Racing Products
Find Your Specific 1960 Pontiac Ventura Performance and Racing Products
Below you will find various in-demand Pontiac Performance and Racing Products, components and accessories for your 1960 Ventura. Advance Auto Parts has popular Ventura parts like Performance Exhaust Products, Performance Ignition Products, Performance Engines and more. You’ll also find aftermarket and OEM Performance and Racing Products for other Ventura model years including
1961,
1971,
1972,
1973,
1974,
1975,
1976,
1977 and more. Select a category of 1960 Pontiac Ventura Performance and Racing Products below and start saving instantly.
Popular 1960 Pontiac Ventura Performance and Racing Products Categories
Essential Performance and Racing Products for 1960 Pontiac Venturas
Edelbrock – Classic Series Valve Covers: Small Block Chevy 262-400 1959-86, Aluminum (Part No.4145)
from
$371.99
The Edelbrock #4145 Classic Series Valve Covers are designed for Chevy 262-400 V8 1959-86 applications. Edelbrock first made these aluminum valve covers in the late ’50s and they’re still a classic. They are made of heavy-gauge sand-cast aluminum, Overall height is measured from base to top at the highest point. Edelbrock classic valve covers can be machined to accept breathers if desired.
Product Features:
See More
Product Features:
- Small Block Chevy 262-400 1959-86
- Tall
- Polished Aluminum
- Set Of Two
Mallory – Unilite Breakerless Ignition Conversion Kit (Part No.503M)
from
$176.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.
Product Features:
See More
Product Features:
- Easy Installation
- Improved Fuel Economy
- Reduced Maintenance
- Accurate Timing
- Improved Performance
- Provides A Simple Conversion
- No Moving Parts To Wear Out
Edelbrock – Thunder AVS Carburetor #1826 650 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No.1826)
from
$464.99
New or reconditioned 650cfm. Square-flange. Electric choke without EGR. Primary jet 0.095. Secondary jet 0.098. Metering Rod 0.065 x 0.047. Dual plane intake. Spring loaded needles and seat increase performance. New qwik-tune adjustable secondary air valve. Distinctive black accented hardware. Lightweight ball burnished aluminum. No gaskets below fuel level to prevent leakage. Metering rod and step up springs can be changed easily. GM and AMC style throttle linkage.
Product Features:
See More
Product Features:
- Spring Loaded Needles/Seat Increase Performance
- New Qwik-Tune Adjustable Secondary Air Valve
- Distinctive Black Accented Hardware
- Lightweight Ball-Burnished Aluminum
- No Gaskets Below Fuel Level to Prevent Leakage
- Metering Rod/Step Up Springs Can Be Changed Easily
- GM/AMC-Style Throttle Linkage
Mallory – Distributor Wiring Harness (Part No.29349)
Competition Cams – High Energy 212/212 Hydraulic Flat Cam K-Kit (Part No.K51-230-3)
from
$622.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.
Product Features:
See More
Product Features:
- Good blend of efficiency and performance.
- Perfect choice for performance street rebuilds.
- Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
Edelbrock – Water Pump for Pontiac, Standard Rotation in Black Finish (Part No.88563)
from
$385.99
Edelbrock #88563 Water Pump Pontiac 389-455 standard rotation black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooli
Product Features:
See More
Product Features:
- Standard Impeller Rotation
- 0.625 in. Pilot Shaft
- 0.750 in. Ball/Ball Bearing
- 4.50 in. Block To Hub Height
- Black Finish
Mr. Gasket – Alternator Bracket (Part No.9850)
from
$25.99
Hold your alternator securely in place with Mr. Gasket chrome alternator bracket. Chrome plated heavy gauge steel for long lasting good looks. Must be used with #9852.
Product Features:
See More
Product Features:
- Chrome Plated Steel
- F-Style
- Heavy Gauge Steel Construction
- Fits Small Block Chevy 265-400 CID
- Must Be Used With Part 9852
PerTronix – D4260 Flame-Thrower Distributor Rotor HEI/EST Black (Part No.D4260)
from
$10.99
Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.
Product Features:
See More
Product Features:
- Made from hi-performance 60 KV rated alkyd molding compound.
- Cap and rotor kits include nylon rotor hold-down screws.
- Flame-Thrower dust covers provide a larger air gap around the coil.
Competition Cams – MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST (Part No.1412-16)
from
$213.99
These Magnum Roller Rocker Arms for Chevy V8 265-400 and V6 200-262 applications are the ultimate street rocker. With a 3/8″ stud diameter and 1.52 ratio, they are designed for serious performance enthusiasts. All Magnum Roller Rocker Arms are constructed
Product Features:
See More
Product Features:
- Roller tip reduces friction while stiff design and superior ratio accuracy yield more effective valve lift
- For applications with less than 350 lbs. of open spring pressure
- Constructed from 8620 chromemoly steel, a superior material that will not flex and ensures maximum lift
- Ultimate street roller rocker arm designed for serious performance enthusiasts
Competition Cams – Ultra-Gold ARC Rocker Set w/ 1.6 Ratio for Chevrolet Small Block w/ 3/8" Stud (Part No.19002-16)
from
$412.99
These COMP Cams Ultra-Gold Aluminum Roller Rocker Arms with a 3/8″ stud diameter and 1.6 ratio are designed for Chevrolet V8 265-400 applications. The new modern design features of these Ultra-Gold Rockers are proven to withstand extremely aggressive spring pressure and valve lift. Designed specifically for high performance street and race engines, the Ultra-Gold Aluminum Rocker Arms are precision CNC-machined to strict tolerances. Developed to meet the demands of professional engine builders, these rockers include features never before possible in an aluminum rocker arm.
Product Features:
See More
Product Features:
- CNC-machined, lightweight design removes weight and yields unrivaled quality and ratio accuracy
- Designed for high performance street and race engines
- Precision-sorted trunion bearings withstand elevated valve spring pressure and valve lift
- Additional clearance, up to 1.650″ O.D. valve spring
Mallory – Mallory Unilite Dist.: Pontiac 301-455 (Part No.3758001)
from
$538.99
The industry standard with adjustable mechanical advance curve. Triggered by photo-optic infrared LED system. Improved combustion efficiency and economy, increased spark plug life and cold weather starting, and maintenance free operation.
Product Features:
See More
Product Features:
- Improved Combustion And Economy
- Increased Spark Plug Life
- Improved Cold Weather Starting
- Maintenance Free Operation
- Accurate Spark Timing
- Self-Lubricating Bushings
- Years Of Trouble-Free Service
Accel – Dist:Chev V8 Hei Vac W/Coil (Part No.59107C)
from
$210.99
Performance Replacement HEI Distributor, direct plug-in with OE type connectors, GM HEI equipped Cars, Trucks (Pre-Computer). High dielectric strength cap, brass male towers. ACCEL Performance Replacement Distributors are the perfect choice for your daily driver or street machine. Using all new components, these distributors feature High-performance ACCEL Electronics. All new components-housings are either new castings or turned from billet stock, centerless ground shaft with oil lite bushings. High dielectric strength cap, balanced rotor. Male tower distributor cap with brass cap and rotor contacts (Ford and AMC Models feature screw-mounted wire retainer for the ultimate plug wire retention). Iron or steel distributor gear. Direct plug-in replacement with factory-type connectors for plug and play installation.
Product Features:
See More
Product Features:
- Direct Plug In Factory Replacement Plug And Play
- CNC Machined 6061 T6 Billet Aluminum Housing
- High Dielectric Strenght Thermoplastic Cap With Br
- 4 Topin Module With Dwell Control Triggers At 75 R
- Easy Access Fully Adjustable Mechanical Advance
- Adjustable Vacuum Advance
- Includes Performance Coil
- Fit non computerized vehicles
Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)
from
$186.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).
Product Features:
See More
Product Features:
- Glass Filled Polyester Case
- Longer Spark Duration
- Increased Performance
- No Energy Loss Due To Arcing
- Includes Brass Contact Terminal
Accel – Supercoil (Part No.140001)
from
$105.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.
Product Features:
See More
Product Features:
- Oil Filled For Better Cooling
- Optimized Low Resistance
- Silicon Magnetic Steel E-Core
- Higher Energy/Voltage Outputs
- Quicker Starts
- Improved Idle Quality
- Resists Shock And Vibration
- Resists Corrosion
Mr. Gasket – Oil Pan Bolt Kit (Part No.6086)
from
$30.19
The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.
Product Features:
See More
Product Features:
- Ideal For Tight Spaces
- Serrations Prevent Loosening
- Flange Distributes Pressure
- Zinc Plated Bolts
- Grade 5 Material
- Easy Installation
Mr. Gasket – Oil Pan Bolt Kit (Part No.6085)
from
$17.49
The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.
Product Features:
See More
Product Features:
- Ideal For Tight Spaces
- Serrations Prevent Loosening
- Flange Distributes Pressure
- Zinc Plated Bolts
- Grade 5 Material
- Easy Installation
FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1803)
from
$26.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
- With steel core to provide ultimate excellent blowout resistance.
- Not intended for use in emission controlled vehicles.
FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1814)
from
$30.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
- With steel core to provide ultimate excellent blowout resistance.
- Not intended for use in emission controlled vehicles.
Mallory – Distributor Condenser (Part No.401)
from
$17.09
Distributor Condenser
Mr. Gasket – Valve Cover Gasket Set (Part No.585G)
from
$29.49
Molded rubber gaskets are reusable, great for engines that require valve lash maintenance. These gaskets feature Nitrile material for long life, solid steel carrier for strength and rigidity. Incorporates compression limiters to prevent fastener over-tightening.
Product Features:
See More
Product Features:
- Features Nitrile Rubber Material For Long Life
- Molded Rubber Gaskets Are Reusable
- Ideal For Engine Requiring Valve Lash Maintenance
Edelbrock – Valve Cover Gasket Set for Chevrolet (Part No.7549)
Hurst – Installation Kit, Competition Plus Shifter (Part No.3737834)
from
$277.99
The Hurst Competition Plus installation kits are designed so that your shifter fits directly into your muscle car, with the least possible modifications to the vehicle. Includes arms, rods, mounting plate, bushings, and all necessary hardware.
Product Features:
See More
Product Features:
- Competition Plus Shifter Installation Kit
- Includes Hardware
- Durable
- Sold as a Kit
- Hurst Quality
Hurst – Automatic Shifter, Quarter Stick (Part No.3160006)
from
$426.99
The Hurst Quarter Stick is designed for 2 and 3 speed applications. Its precision gate style mechanism ensures a positive feel. It features, a neutral safety switch, NHRA approved reverse lockout, and a brushed aluminum cover.
Product Features:
See More
Product Features:
- Forward and Reverse Shift Patterns
- Chrome Plated Trigger for Detent Activity
- Factory Neutral Safety Switch
- Compact And Lightweight
- Roller Detent with Shifter Pattern
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1016)
from
$67.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
- Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
- Raises combustion sealing force to roughly three times that of standard head gaskets.
- Steel wire rings for the greatest combustion seal strength.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Ultra Seal: Head Gasket (Part No.5799G)
from
$68.99
Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.
Product Features:
See More
Product Features:
- Five layer (graphite core/perforated steel outer layers) composite construction
- Graphite core is excellent transfering heat away from hot spots in head preventing gasket burn-out.
- Provides excellent stability, compressibility and high temperature endurance
- Coated with high temperature silicone to ensure sealing of engine fluids
- Will not brinell (indent) aluminum cylinder heads
- For high performance street, drag race and oval track use
- Compatible w/High Octane Fuel
- Compatible With Exotic Fuel
Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)
from
$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens At 180 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
Upgrade your 1960 Pontiac Ventura with Top-Quality Performance and Racing Products
When it comes to maintaining or upgrading your 1960 Pontiac Ventura, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Pontiac or enhancing its overall performance, Performance and Racing Products are key to keeping your Ventura functioning at its best. At Advance Auto Parts, we offer a wide selection of 35 Performance and Racing Products for the 1960 Pontiac Ventura, designed to meet your needs without breaking the bank.
From
Performance Exhaust Product
replacements to
Performance Ignition Products
upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.
Affordable Prices and Wide Selection
Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1960 Pontiac Ventura at great prices.
Our Performance and Racing Products inventory for this model
ranges from just $10.99 to $622.99, with
an average price of $229.58.
Our 35 Performance and Racing Products in stock come from 9 trusted brands, so you’re sure to find the right part for your 1960 Pontiac Ventura without overspending.
Top Brands and High Customer Satisfaction
Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1960 Pontiac Ventura, we stock popular OEM and aftermarket Performance and Racing Products from top names
like Mallory, Edelbrock, Mr. Gasket, and more.
Mallory Performance and Racing Products
start at just $17.09 and boast an impressive 5 stars average rating from customers.
Edelbrock and Mr. Gasket also bring quality to the table, with Performance and Racing Products available starting at $25.99, and at an average 4 stars rating.
With 122 customer reviews and counting, our 1960 Pontiac Ventura Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.
Explore Related Parts and More
While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Fluids and Chemicals
and more to make sure your 1960 Pontiac Ventura is always ready to roll. We’re committed to providing you with everything you need to keep your Ventura in top shape, all in one place.
Start shopping confidently below for your 1960 Pontiac Ventura!
Best-Selling Performance Exhaust Products for 1960 Pontiac Venturas
Enhance the driving experience in your Pontiac with 1 quality Performance Exhaust Product components, starting at $25.99.
Mr. Gasket – Alternator Bracket (Part No.9850)
from
$25.99
Hold your alternator securely in place with Mr. Gasket chrome alternator bracket. Chrome plated heavy gauge steel for long lasting good looks. Must be used with #9852.
Product Features:
See More
Product Features:
- Chrome Plated Steel
- F-Style
- Heavy Gauge Steel Construction
- Fits Small Block Chevy 265-400 CID
- Must Be Used With Part 9852
Most Popular 1960 Pontiac Ventura Performance Ignition Products
Customize your Pontiac with 7 Performance Ignition Products products
like Performance Coils,
Performance Ignition Kits, and
Performance Ignition Parts, all
priced under $186.99.
Mallory – Unilite Ignition Module (Part No.605)
from
$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.
Product Features:
See More
Product Features:
- Service Part
- No Moving Parts To Wear Out
- Self Contained Unit
- Can Drive OEM
- Can Drive High Performance Ignition Coils
Mallory – Mallory Kit: Unil Conv: Delco: V8 (Part No.501)
from
$134.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.
Product Features:
See More
Product Features:
- Easy Installation
- Improved Fuel Economy
- Reduced Maintenance
- Accurate Timing
- Improved Performance
- Provides A Simple Conversion
- No Moving Parts To Wear Out
MSD Ignition – Blaster 2 Coil: High Performance Ignition Upgrade (Part No.8202)
from
$49.99
If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.
Product Features:
See More
Product Features:
- Improved output coil for electronic ignitions
- Works w/Blaster Ignition Or MSD 5/6/7 Series
- Ballast Resistor Required If Used w/Stock Points Ignition
- Alkyd tower w/high dielectric properties lessens carbon tracking
Mallory – Distributor Wiring Harness (Part No.29349)
Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)
from
$186.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).
Product Features:
See More
Product Features:
- Glass Filled Polyester Case
- Longer Spark Duration
- Increased Performance
- No Energy Loss Due To Arcing
- Includes Brass Contact Terminal
Mallory – Unilite Breakerless Ignition Conversion Kit (Part No.503M)
from
$176.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.
Product Features:
See More
Product Features:
- Easy Installation
- Improved Fuel Economy
- Reduced Maintenance
- Accurate Timing
- Improved Performance
- Provides A Simple Conversion
- No Moving Parts To Wear Out
Mallory – Distributor Condenser (Part No.401)
from
$17.09
Distributor Condenser
Top Picks for 1960 Pontiac Ventura Performance Engines
Upgrade Pontiac Venturas with top-quality Performance Engines parts, including 9 OEM and aftermarket selections for your 1960 model.
Edelbrock – Water Pump for Pontiac, Standard Rotation in Black Finish (Part No.88563)
from
$385.99
Edelbrock #88563 Water Pump Pontiac 389-455 standard rotation black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooli
Product Features:
See More
Product Features:
- Standard Impeller Rotation
- 0.625 in. Pilot Shaft
- 0.750 in. Ball/Ball Bearing
- 4.50 in. Block To Hub Height
- Black Finish
Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)
from
$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.
Product Features:
See More
Product Features:
- Opens At 180 Degrees
- Designed to Resist Large Variations of Coolant Pressure at High RPM
- Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
- For High Performance Street, Drag Race, and Oval Track
- Copper & Brass Construction – Resists Corrosion
- High Flow
FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1814)
from
$30.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
- With steel core to provide ultimate excellent blowout resistance.
- Not intended for use in emission controlled vehicles.
Edelbrock – Performer-Plus Camshaft Kit for Pontiac 350-403 V8 (Part No.2157)
from
$358.99Product Features:
- Designed for Optimum Torque and Acceleration
- Maximum Performance From Idle through Mid-Range
- Matched to Edelbrock Performer Intakes
- Includes Hydraulic Lifters and Assembly Lube
- Major Improvement in Throttle Response and Torque
- Use For Daily Drivers/Trucks/Vans/RVs/4x4s
- Take The Guesswork Out Of Camshaft Selection
FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1622)
from
$32.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
- Not intended for use in emission controlled vehicles.
Mr. Gasket – Ultra Seal: Sure-Lock Rocker Arm Nuts (Part No.923G)
from
$87.19
Designed to keep the rocker arms positively locked for precise and critical valve train adjustments. Manufactured from quality grade steel, then heat-treated for extra strength and plated with a durable finish. Kits include 16 rocker arm nuts with socket head set screws and one hex key wrench.
Product Features:
See More
Product Features:
- (16) Rocker Arm Nuts w/ Locks 3/8″-24 Threads
- Shank O.D. .540″
- Includes Locks and Hex Wrench
- High-Quality Grade Steel
- Heat-Treated For Ex Strength
- Plated With Durable Gold Tone Finish
FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1016)
from
$67.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions
Product Features:
See More
Product Features:
- Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
- Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
- Raises combustion sealing force to roughly three times that of standard head gaskets.
- Steel wire rings for the greatest combustion seal strength.
- Not intended for use in emission controlled vehicles.
Competition Cams – High Energy 212/212 Hydraulic Flat Cam K-Kit (Part No.K51-230-3)
from
$622.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications.
Product Features:
See More
Product Features:
- Good blend of efficiency and performance.
- Perfect choice for performance street rebuilds.
- Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
FEL-PRO Performance – Performance Valve Cover Gasket Set (Part No.1623)
from
$23.29
Fel-Pro® Performance Gaskets deliver reliable sealing under grueling racing conditions.
Product Features:
See More
Product Features:
- Blue Stripe® performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
- Not intended for use in emission controlled vehicles.
In-Demand Performance Distributors for 1960 Pontiac Venturas
Select from 4 premium Performance Distributors parts for your 1960 Pontiac Ventura, with prices ranging from $10.99 to $538.99.
PerTronix – D4061 Flame-Thrower HEI Distributor Rotor Red (Part No.D4061)
from
$15.99
Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.
Product Features:
See More
Product Features:
- Made from hi-performance 60 KV rated alkyd molding compound.
- Cap and rotor kits include nylon rotor hold-down screws.
- Flame-Thrower dust covers provide a larger air gap around the coil.
Mallory – Mallory Unilite Dist.: Pontiac 301-455 (Part No.3758001)
from
$538.99
The industry standard with adjustable mechanical advance curve. Triggered by photo-optic infrared LED system. Improved combustion efficiency and economy, increased spark plug life and cold weather starting, and maintenance free operation.
Product Features:
See More
Product Features:
- Improved Combustion And Economy
- Increased Spark Plug Life
- Improved Cold Weather Starting
- Maintenance Free Operation
- Accurate Spark Timing
- Self-Lubricating Bushings
- Years Of Trouble-Free Service
PerTronix – D4062 Flame-Thrower HEI Distributor Rotor Blue (Part No.D4062)
from
$15.99
Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.
Product Features:
See More
Product Features:
- Made from hi-performance 60 KV rated alkyd molding compound.
- Cap and rotor kits include nylon rotor hold-down screws.
- Flame-Thrower dust covers provide a larger air gap around the coil.
PerTronix – D4260 Flame-Thrower Distributor Rotor HEI/EST Black (Part No.D4260)
from
$10.99
Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provides cooler operating temperatures.
Product Features:
See More
Product Features:
- Made from hi-performance 60 KV rated alkyd molding compound.
- Cap and rotor kits include nylon rotor hold-down screws.
- Flame-Thrower dust covers provide a larger air gap around the coil.
Most Sold 1960 Pontiac Ventura Performance Fuel Systems
Explore our best-selling Pontiac parts for the 1960 Ventura among 9 OEM and aftermarket options starting from $394.99.
Edelbrock – CARBURETOR (Part No.14054)
from
$488.99
Product Features:
See More
- EnduraShine Finish
- GM/AMC-Style Throttle Linkage
- Can Add Electric Choke PN[1478]
- Easy Tuning with 2-Piece Design
- Smooth Secondary Transition
- Both Timed and Full Vacuum Ports
- Includes PCV Outlet
Edelbrock – Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1406)
from
$428.99
The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Electric Choke
- 4 Barrel Count
- Square Bore
- Smooth Secondary Transition
- Both Timed and Full Vacuum Ports
- Includes PCV Outlet
Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)
from
$394.99
The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Manual Choke
- 4 Barrel Count
- Square Bore
- Smooth Secondary Transition
- Both Timed and Full Vacuum Ports
- Includes PCV Outlet
Edelbrock – Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1407)
from
$451.99
The Edelbrock 1407 Performer Series 750 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristic
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Manual Choke
- 4 Barrel Count
- Square Bore
- Smooth Secondary Transition
- Both Timed and Full Vacuum Ports
- Includes PCV Outlet
Edelbrock – Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1400)
from
$498.99
The Edelbrock 1400 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist
Product Features:
See More
Product Features:
- Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
- Electric Choke
- 4 Barrel Count
- Square Bore
- Electric Choke Installed from Factory
- Smooth Secondary Transition
- Includes Only Timed Vacuum Port
- Includes EGR ; Fuel Vapor Outlet
Edelbrock – CARBURETOR (Part No.14064)
from
$541.99
Product Features:
See More
- EnduraShine Finish
- GM/AMC-Style Throttle Linkage
- Electric Choke Installed from Factory
- Easy Tuning with 2-Piece Design
- Smooth Secondary Transition
- Both Timed and Full Vacuum Ports
- Includes PCV Outlet
Edelbrock – Thunder AVS Carburetor #1826 650 CFM With Electric Choke, Satin Finish (Non-EGR) (Part No.1826)
from
$464.99
New or reconditioned 650cfm. Square-flange. Electric choke without EGR. Primary jet 0.095. Secondary jet 0.098. Metering Rod 0.065 x 0.047. Dual plane intake. Spring loaded needles and seat increase performance. New qwik-tune adjustable secondary air valve. Distinctive black accented hardware. Lightweight ball burnished aluminum. No gaskets below fuel level to prevent leakage. Metering rod and step up springs can be changed easily. GM and AMC style throttle linkage.
Product Features:
See More
Product Features:
- Spring Loaded Needles/Seat Increase Performance
- New Qwik-Tune Adjustable Secondary Air Valve
- Distinctive Black Accented Hardware
- Lightweight Ball-Burnished Aluminum
- No Gaskets Below Fuel Level to Prevent Leakage
- Metering Rod/Step Up Springs Can Be Changed Easily
- GM/AMC-Style Throttle Linkage
Edelbrock – Reman Thunder AVS Carb #18129 800 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.18129)
from
$413.99
Product Features:
See More
- Satin Finish
- 4 Barrel
- Aluminum Body Material
- Manual Choke Type
- 800 cfm Maximum Flow Rating
Edelbrock – Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.9907)
from
$407.99
Product Features:
See More
- Satin Finish
- 4 Barrel
- Annular Booster Type
- Manual Choke Type
- 750 cfm Maximum Flow Rating
Top-Rated Performance and Racing Products Brands For Your 1960 Pontiac Ventura
Shop for the best-rated brands offering Performance and Racing Products and other products for your 1960 Pontiac Venturas. Below you’ll find some of our best rated Performance and Racing Products from Mallory, Edelbrock, and Mr. Gasket, and more. Performance and Racing Products from these brands that fit a 1960 Ventura start at just $17.09 and are rated as high as 5 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.
Popular Mallory 1960 Pontiac Ventura Performance and Racing Products
When it comes to maintaining or upgrading your 1960 Pontiac Ventura, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Mallory ticks all of those boxes. We offer a wide selection of Mallory Performance and Racing Products, specifically designed for the 1960 Pontiac Ventura. With over 7 Mallory brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $17.09, with an average price of just $167.26. Plus, with over 4 customer reviews and an average rating of 5 stars, you can trust that our Mallory Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.
Popular Edelbrock 1960 Pontiac Ventura Performance and Racing Products
Edelbrock auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1960 Pontiac Ventura owner should feel confident when installing genuine Edelbrock parts in their vehicle. To ensure the best fit and performance for your 1960 Ventura, Advance Auto Parts carries a full inventory of 11 Edelbrock Performance and Racing Products. Plus you will be keeping your Pontiac in peak condition while saving money because prices on these Edelbrock Performance and Racing Products range from $358.99 to $541.99, plus, with more than 76 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.
from
$498.99
$498.99
This product is not rated
Performer 1400 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
“”
FAQs for 1960 Pontiac Ventura Performance and Racing Products
Which Performance and Racing Products are best-sellers for 1960 Pontiac Venturas?
Out of 35 Performance and Racing Products that fit 1960 Pontiac Venturas, the following parts are the top sellers:
- High Performance 180 Degree Thermostat for Increased Flow (17360033) – $26.99
- Alternator Bracket (6124151) – $25.99
- PERFORMANCE OIL PAN GASKET SET (19781419) – $30.49
What’s the price range for 1960 Pontiac Ventura Performance and Racing Products?
Performance and Racing Product prices for the 1960 Pontiac Ventura start at $10.99 and go up to $622.99 for the most premium parts.
What’s the average price of a Performance and Racing Product for a 1960 Pontiac Ventura?
The average price for Performance and Racing Products for the 1960 Pontiac Ventura is $229.58. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.
Does Advance Auto Parts sell Performance and Racing Products for other Pontiac Ventura model years?
What are the cheapest Performance and Racing Products for my 1960 Pontiac Ventura?
The cheapest 1960 Pontiac Ventura Performance and Racing Products we carry in stock are:
- D4260 Flame-Thrower Distributor Rotor HEI/EST Black (10111551) – $10.99
- D4061 Flame-Thrower HEI Distributor Rotor Red (10111583) – $15.99
- D4062 Flame-Thrower HEI Distributor Rotor Blue (10111488) – $15.99
- Distributor Condenser (17350019) – $17.09
- Performance Valve Cover Gasket Set (19781562) – $23.29
What are the top-rated Performance and Racing Products that fit the 1960 Pontiac Ventura?
Out of 122 reviews by customers, our 1960 Pontiac Ventura Performance and Racing Products have an average customer rating of . These are some of the highest-rated Performance and Racing Product types for the 1960 Pontiac Ventura and their top-rated products:
- Performance Fuel Systems
- CARBURETOR (17340032) – $488.99
- Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (5020654) – $394.99
- Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (5020557) – $451.99
- Performance Exhaust Products
- CARBURETOR (17340032) – $488.99
- Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (5020654) – $394.99
- Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (5020557) – $451.99
What types of Performance and Racing Products do you sell for my 1960 Pontiac Ventura?
As of 2/5/25, these are some of the most in-demand types of Performance and Racing Products for a 1960 Pontiac Ventura:
Can I get help with 1960 Pontiac Ventura Performance and Racing Product orders?
Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Pontiac Performance and Racing Products and more.
What is your return policy for Pontiac Ventura Performance and Racing Products?
Advance Auto Parts keeps returns simple. For new Pontiac Ventura Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.
