from

$26.99

Mechanical Advance Curve Ki tPrecision machined chromoly weights and center plate eliminate erratic timing. Three sets of springs, guide bushings and complete installation instructions make recurving your distributor easy.

Product Features:

PerTronix D9001 Flame-Thrower HEI Distributor Advance Curve Kit
Precision machined chromoly weights and center plate.

from

$15.99

Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provi

Product Features:

PerTronix D4061 Flame-Thrower HEI Distributor Rotor Red
Made from hi-performance 60 KV rated alkyd molding compound.

from

$30.99

Wiring Harness and CapacitorPremium quality wire harness and capacitor insure good connection and “static free” operation.

Product Features:

PerTronix D9007 Flame-Thrower HEI Distributor 4-Pin Wire Harness/Capacitor
Premium quality wire harness and capacitor.

from

$134.99

Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

Easy Installation
Improved Fuel Economy
Reduced Maintenance
Accurate Timing
Improved Performance
Provides A Simple Conversion
No Moving Parts To Wear Out

from

$85.29

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

Service Part
No Moving Parts To Wear Out
Self Contained Unit
Can Drive OEM
Can Drive High Performance Ignition Coils

from

$30.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$48.49

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$48.49

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$60.99

ACCEL cap and rotor kits offer superior protection from “arc-thru” and crossfire. Features 60k V-rated alkyd compound, stress-relieved at molding to ensure stability. Brass inserts and steel rotor springs provide for high spark energy flow.

Product Features:

See catalog for application information
Features 60K V Rated Alkyd Compound

from

$105.99

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

More Accurate Ignition Timing
Improves Performance And Fuel Economy
Provides More Accurate Ignition Timing
Easy To Install w/Hand Tools
Reduced Maintenance
Thermal Clad Based Surface Mount Construction
Utilizes Specialized Electronic Circuitry
Ignition Timing Is Stable From 1 To 10000rpm

from

$72.99

Stock style replacement modified HEI coil dust cover. Used on 8 cylinder vehicles only.

Product Features:

Externally mounted coil
Increases reliability
Increase performance
High quality plastic
Resist spark loss
Use brass conductors
Low resistance connections
No modifications

from

$76.99

The updated Fuel Pump Booster is an easy way to maintain the proper fuel pressure on your car after adding a power adder such as a turbo or supercharger. The new model allows you to make your boost adjustments through a PC for improved control and accuracy. The Booster ensures that the engine receives the fuel it needs to make up for the increase in air being pumped into the intake manifold. It will increase the voltage to the factory fuel pump in proportion to manifold boost pressure in order to maintain the proper fuel delivery. The amount of increase is adjustable from a range of an additional 1.5 -22 volts up to 30 psi which can all be set and adjusted from your PC with MSD’s easy to use Windows based software. The MSD Booster will wire to the factory fuel pump relay or with a secondary booster pump.

Product Features:

Direct performance replacement
For GM 2 Tower Coils Used From Mid 1980s To Late 1990s
80:1 turns ratio
Lower Primary Resistance Produces High Voltage Output
Works w/Stock Ignition As Well As MSD Ignitions
CARB E.O. Approved

from

$105.99

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:

Oil Filled For Better Cooling
Optimized Low Resistance
Silicon Magnetic Steel E-Core
Higher Energy/Voltage Outputs
Quicker Starts
Improved Idle Quality
Resists Shock And Vibration
Resists Corrosion

from

$14.99

The throttle cable bracket is designed for small block Chevy engines thru 1979 and is to be used in conjunction with the kick down cable Pn9886 for the Turbo 350 transmission. The throttle cable bracket mounts on the intake manifold and will hold cables with round or square mounts. It has a 2 inch adjustable range and is finished off in a beautiful chrome plating.

Product Features:

2 in. adjustable range
Includes necessary hardware
Chrome plated
Individually packaged

from

$54.39

Heavy duty points sets are quipped with extra think contack arms to prevent flexing at high RPMS. Large radiused tungsten contants provide crisp circuit breaking for peak coil output. High strength phenolic rubbing blocks provide superior durability when used with heavy duty spring tension.

Product Features:

Extra Thick Contact Arms
Large Radius Tungsten Contacts
High Strength Phenolic Rubbing Blocks
Prevents Points Float
Moisture-Proof Buna-N Condenser

from

$17.09

Distributor Condenser

from

$27.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$25.99

Hold your alternator securely in place with Mr. Gasket chrome alternator bracket. Chrome plated heavy gauge steel for long lasting good looks. Must be used with #9852.

Product Features: