1958 Dodge Coronet Performance Engines

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers.

The Edelbrock valve cover gaskets No: 7591 provide excellent sealing integrity and conformability for easy installation. The multi-layer construction has two highly compressible, high rubber content, fiber-reinforced outside layers which are chemically bonded to a high strength composite core. This unique core-reinforced construction has a radial strength to resist high-vacuum or blow-out conditions. Edelbrock valve cover gaskets are an Edelbrock product.

The Edelbrock valve cover gaskets No: 7592 provide excellent sealing integrity and conformability for easy installation. The multi-layer construction has two highly compressible, high rubber content, fiber-reinforced outside layers which are chemically bonded to a high strength composite core. This unique core-reinforced construction has a radial strength to resist high-vacuum or blow-out conditions. Edelbrock valve cover gaskets are an Edelbrock product.

Fel-Pro® Performance Gaskets deliver reliable sealing under grueling racing conditions.

Edelbrock part No: 7276 Intake Gaskets for 1966-87 318-340-360 Chrysler engines allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, and for a longer period of time. The new MP-2N Micropore technology does not use solvents making our gaskets environmentally friendly. Impervious to most chemicals, this synthetic fiber composite provides a high recovery under load. This means that when compressed, the gasket will conform to any imperfections on the sealing surface even using lower flange pressures. A nitrile bead around each port opening makes the seal even better.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Graphite & steel construction, proprietary polymer coated. 4.140 inch Gasket Bore, .028 inch Compressed Thickness.

Mr. Gasket Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. With today’s extreme compression ratios you need stronger more durable gaskets. Mr. Gasket steel shim gaskets are made from .020 inch steel shim stock which is thinner than most composite gaskets increasing engine compression. Stress formed embossments will seal the extreme cylinder pressure.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.

Edelbrock part No: 7804 Performer-Link timing chain is for use with Edelbrock or stock cams. They have a solid-bushing chain for a true bearing surface that rolls with the sprockets, eliminating chain stretch. Cam sprockets are made from 35,000 psi tensile strength cast iron. Crank sprockets are made from billet SAE-1144 steel and induction heat treated. Four Performer-Link sets are stock replacement parts and 50-state legal (see listings in bold type). All other sets have three keyway setting points to ensure accurate timing selection for early or late-model vehicles. Performer-Link timing sets are not for use above 6500 rpm. Performer roller chain sets are engineered to operate up to 6500 rpm. Never hammer directly on chain or sprockets. You can crack the hardened links and pins and cause early failures. Use a sleeve for installations that require hammering, a brass drift punch may be used if you carefully alternate blows on either side of the sprocket to avoid cocking. Never stretch the chain with a screwdriver. Check for clearance between the timing chain and block and between the chain and front cover before reassembly. Be sure that both cam and crank sprockets are exactly in line with each other. Misalignment can cause chain to break.

Edelbrock part No: 7805 Performer-Link timing chain is for use with Edelbrock or stock cams. They have a solid-bushing chain for a true bearing surface that rolls with the sprockets, eliminating chain stretch. Cam sprockets are made from 35,000 psi tensile strength cast iron. Crank sprockets are made from billet SAE-1144 steel and induction heat treated. Four Performer-Link sets are stock replacement parts and 50-state legal (see listings in bold type). All other sets have three keyway setting points to ensure accurate timing selection for early or late-model vehicles. Performer-Link timing sets are not for use above 6500 rpm. Performer roller chain sets are engineered to operate up to 6500 rpm. Never hammer directly on chain or sprockets. You can crack the hardened links and pins and cause early failures. Use a sleeve for installations that require hammering, a brass drift punch may be used if you carefully alternate blows on either side of the sprocket to avoid cocking. Never stretch the chain with a screwdriver. Check for clearance between the timing chain and block and between the chain and front cover before reassembly. Be sure that both cam and crank sprockets are exactly in line with each other. Misalignment can cause chain to break.

Edelbrock part No: 7803 Performer-Link timing chain is for use with Edelbrock or stock cams. They have a solid-bushing chain for a true bearing surface that rolls with the sprockets, eliminating chain stretch. Cam sprockets are made from 35,000 psi tensile strength cast iron. Crank sprockets are made from billet SAE-1144 steel and induction heat treated. Four Performer-Link sets are stock replacement parts and 50-state legal (see listings in bold type). All other sets have three keyway setting points to ensure accurate timing selection for early or late-model vehicles. Performer-Link timing sets are not for use above 6500 rpm. Performer roller chain sets are engineered to operate up to 6500 rpm. Never hammer directly on chain or sprockets. You can crack the hardened links and pins and cause early failures. Use a sleeve for installations that require hammering, a brass drift punch may be used if you carefully alternate blows on either side of the sprocket to avoid cocking. Never stretch the chain with a screwdriver. Check for clearance between the timing chain and block and between the chain and front cover before reassembly. Be sure that both cam and crank sprockets are exactly in line with each other. Misalignment can cause chain to break.

Manufactured from high-density cork/rubber blend gasket material. Provides excellent sealing and durability. For original equipment replacement and high performance street.

Manufactured from cellulose/nitrile composition gasket material. A black latex rubber coating is applied to outside of gasket to help seal minor oil pan rail irregularities and eliminate the possibility of oil leakage. Provides excellent sealing and durability. Complete with molded rubber front/rear oil pan seals where applicable. For original equipment replacement, high performance street, drag race and oval track.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

These grade 5 socket head bolts are zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8-16 x 1 inch bolts & washers.

Edelbrock CH-28 Chrysler Big Block RB Dual-Quad Intake Manifold, 5440.

Edelbrock Performer Intake Manifold Small-Block Chrysler, 3776.

Edelbrock Performer RPM Small Block Chrysler Intake Manifold, 7176.

Designed for 440 c.i.d. Chrysler engines with 3×2-bbl, carbs, also fits 413 and 426 Wedge. #2475 is stock replacement/street legal part for 440 V8s with OEM 3×2-bbl. carbs; 1968-71. This manifold was original equipment on Chrysler 440 Six-Pack engines, Chrysler #P04529056. Will not fit 1962-64 Max Wedge heads.

Edelbrock Performer 318/360 Intake Manifold for Small-Block Chrysler, LA Series Engines, 2176.