1958 Chevrolet Corvette Fuel and Emissions Systems
More 1958 Chevrolet Corvette Fuel and Emissions Systems Categories
If you’re looking for an original Fuel and Emissions Systems replacement for a 1958 Chevrolet Corvette, you can search through our selection below. You’ll also find aftermarket and OEM Fuel and Emissions Systems to meet your needs.
Essential 1958 Chevrolet Corvette Fuel and Emissions Systems
Carquest Premium – Locking Fuel Cap: 10522, Twist-Lock, Direct Fit, Provides Tight Seal, 1 Pack (Part No.10522)
from
$22.99
Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.
Product Features:
See More
Product Features:
- Protects your fuel from theft and vandalism
- Passes all state and federal emissions tests
- Manufactured from durable, long-life materials
- Reduces air pollution with proper sealing and venting
- Independently tested for emission control
Carquest Premium – Keyed Alike Locking Fuel Cap (Part No.17591)
from
$11.99
None
Product Features:
See More
Product Features:
- Protects your fuel from theft and vandalism
- Manufactured from durable, long-life materials
- Independently tested for emission control
- Passes all state and federal emissions tests
- Reduces air pollution with proper sealing and venting
Carquest Premium – Fuel Cap: 10640, Twist-Lock, Direct Fit, Provides Tight Seal, 1 Pack (Part No.10640)
from
$8.79
Manufactured with OEM quality materials and safety standards by an OE Supplier. Manufactured to pass all state and federal emissions requirements. Specifically designed pressure and vacuum relief valves to prevent evaporation of fuel. A leaking fuel cap can allow up to 30 gallons of gasoline to evaporate over the period of a year.
Product Features:
See More
Product Features:
- Passes all state and federal emissions tests
- Manufactured from durable, long-life materials
- Reduces air pollution with proper sealing and venting
- Independently tested for emission control
Mr. Gasket – Fuel Pump Block-Off Plate (Part No.1515)
from
$12.99
This is what you need when changing your manual fuel pump to electric. It blocks the hole that remains when you remove the mechanical fuel pump from the engine to keep the oil inside. This plate is precision machined and is chrome plated.
Product Features:
See More
Product Features:
- Chrome Plated Steel
- Comes With Gasket
Spectre – Sbc Blk Off Plate W/Bolts (Part No.42463)
from
$12.99
Spectre’s triple chrome plated Fuel Pump Block Off Plate was designed for small block Chevrolet engines. Engineered for optimum fit and function, this kit includes a block off plate gasket and chrome mounting bolts with washers.
Product Features:
See More
Product Features:
- Necessary if switching to electric fuel pump
- Includes block off plate gasket
- Includes chrome mounting bolts with washers
- Triple chrome plated
Mr. Gasket – Fuel Pump Block-Off Plate (Part No.1516)
from
$12.99
Precision cut to cover stock fuel pump opening when converting to an electric fuel pump. Gasket included.
Product Features:
See More
Product Features:
- Chrome Plated Steel
- Comes With Gasket
- Easy Installation
GM Genuine Parts – Multi-Port Fuel Injector Rail (Part No.217-1619)
from
$249.99
GM Genuine Parts Fuel Injector Rails are designed, engineered, and tested to rigorous standards, and are backed by General Motors. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).
Product Features:
See More
Product Features:
- Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
- GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
- GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
- GM regularly updates production and service part designs to integrate new materials and technologies
Edelbrock – Fuel Injection Fuel Rail #3627, -6 AN Black Anodized For Chevrolet Small-Block (Part No.3627)
from
$211.99
All Edelbrock fuel rails are machined from high quality extruded aluminum. Each kit includes fuel rails, stands and mounting hardware. Fuel fittings, crossover line and regulator not included. 3627 Small-Block Chevy fuel rail kit is for use with Pro-Flo X
Product Features:
See More
Product Features:
- Black AnodizedFinish
- High Capacity Fuel Rails
- For Use W/ Pro-Flo XT Manifold #7137
- -6 AN Inlet / Outlet
- Made In The USA
KAI – Fuel Tank (Part No.FTK010118)
from
$234.99
New Platinum Pro Fuel Tank 20 Gallon
Product Features:
See More
Product Features:
- 20 Gallon, With EEC, Excludes 430HP
- Meets All Federal Motor Safety Standards
- No Drilling Needed For Installation
- No Modifications Needed For Installation
- Direct Fit Replacement For Your Vehicle
- Same Form Fit And Function As OE
- Check Out The Large Selection Of Parts Available For Your Vehicle
KAI – Fuel Tank (Part No.FTK010283)
from
$239.99
New Platinum Pro Fuel Tank 20 Gallon
Product Features:
See More
Product Features:
- 20 Gallon, Includes Lock Ring Kit
- Meets All Federal Motor Safety Standards
- No Drilling Needed For Installation
- No Modifications Needed For Installation
- Direct Fit Replacement For Your Vehicle
- Same Form Fit And Function As OE
- Check Out The Large Selection Of Parts Available For Your Vehicle
Spectra Premium – Fuel Tank (Part No.GM45A)
from
$297.99
Innovative engineering, manufacturing technology and quality control ensure that Spectra Premium fuel tanks meet or exceed the performance of the original equipment they replace.
Product Features:
See More
Product Features:
- Unit is designed to OE fit, form and function requirements accomplished by leveraging our OE fuel system design expertise
- Lock ring included with each tank to reduce installation time and to ensure a complete repair
- Made with corrosion resistant, OE approved, Ni Terne steel for durability
- Unit is leak tested after production to ensure product in free from fuel and / or evaporative leaks
- Each new fuel tank is road tested to ensure real world performance and to verify that each design meets our high standards for quality
- Engineered to stringent tolerances based on our Canadian engineers’ in-depth knowledge of the OE part it’s designed to replace
- Fit tested on the very same vehicle application for which it was developed verifying first-hand that the design fits properly and can be easily installed
- Packaged with double-layered foam wrap and heavy-gauge corrugated board to ensure product quality at installation
Felpro – Fuel Pump Mounting Gasket (Part No.6579)
from
$2.99
Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Holley – Mechanical Fuel Pump (Part No.12-454-20)
from
$212.99
Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.
Product Features:
See More
Product Features:
- High Output Fuel Flow
- Flows 170 gph Free Flow
- Shutoff Pressure Pre-Set At 8 PSI
- Fuel Pressure Regulator Required
- Heavy Duty Construction For Continuous High rpm Operation
- Redesigned High Flow Valves Ensure Adequate Fuel Delivery
- Fuel Body Casting Can Be Rotated For Plumbing Situations
- 3/4in.-16 Inlet And Outlet Ports
- Fittings Not Included
Delphi – Electric Fuel Pump: With Grommet, Insulating Sleeve, Isolator, Pump Retainer, Seals, Isolator (Part No.FE0110)
from
$112.99
100 years of OE experience, supplier to the world’s top automakers, OE Heritage and knowledge built into every aftermarket part, comprehensive portfolio for a wide range of vehicles and model years.
Product Features:
See More
Product Features:
- Delphi is a global OE manufacturer and all fuel pumps are built to Delphi’s OE standards
- Delphi pumps are designed to operate under extreme temperatures with quick engine starts and to avoid low-fuel hesitation, including alcohol fuels and blends
- Improved pump performance as a result of Delphi’s innovative design and durability
- Restores fast pressure performance and system integrity, translating to better pumping through less energy
- Part is validated, tested and matched to the right vehicle application
- Lower amperage draws less load on vehicle’s electrical system
- Always be sure to check and clean fuel tank to avoid unnecessary returns
- Always replace the fuel strainer when doing a fuel pump repair
KAI – Electric Fuel Pump (Part No.FMD010061)
from
$74.99
New Platinum Pro Electric Fuel Pump, New Strainer Required For Warranty
Product Features:
See More
Product Features:
- Meets All Federal Motor Safety Standards
- No Drilling Needed For Installation
- No Modifications Needed For Installation
- Direct Fit Replacement For Your Vehicle
- Same Form Fit And Function As OE
- Check Out The Large Selection Of Parts Available For Your Vehicle
Delphi – Fuel Pump Module Assembly (Part No.FG1213)
from
$444.99
100 years of OE experience, supplier to the world’s top automakers, OE Heritage and knowledge built into every aftermarket part, comprehensive portfolio for a wide range of vehicles and model years.
Product Features:
See More
Product Features:
- Delphi is a global OE manufacturer and all fuel pumps are built to Delphi’s OE standards
- Empty float height and float retention matches OE specifications and guarantees correct gas gauge reading
- Lower amperage draws less load on vehicle’s electrical system
- Part is validated, tested and matched to the right vehicle application
- Always be sure to check and clean fuel tank to avoid unnecessary returns
- Lower failure rates due to its innovative design and durability
Edelbrock – EGR Valve Adapter #1476 For Intake Manifold #3701 And #3706 (Part No.1476)
ARP Auto Racing – For Use With Chevy, Hex Style Head Type, Polished, Stainless Steel, With Washers (Part No.430-1602)
from
$12.29
Make sure that mechanical fuel pumps stay properly aligned by using ARP durable black oxide finished chrome moly or rust proof stainless bolts(both materials are rated at 170,000 PSI and considerably stronger than Grade 8 hardware). Your choice of either conventional hex heads or 12 point head. Washers are included.
Product Features:
See More
Product Features:
- Nominally Rated At 170,000 PSI Tensile Strength
- Properly Aligned
- Conventional Hex Heads
- Rust-Proof Stainless Bolts
- 170,000 PSI
Mr. Gasket – Fuel Pump Mounting Plate (Part No.1514)
from
$16.99
Ideal for mounting a stock original equipment pump. The mounting plate is precision cut to cover the stock fuel pump opening and is complete with gasket.
Product Features:
See More
Product Features:
- Chrome Plated Steel
- Comes With Gasket
ARP Auto Racing – Chrome Moly (Part No.134-8701)
from
$22.79
Stock fuel pump pushrods leave a lot to be desired. In fact, they have been known to break at the most inopportune time. To provide you with required reliability and improved performance, ARP has developed these sophisticated and durable pushrods. they are made from premium grade aerospace chrome moly and center less ground to precise diameter. A hollow core serves to reduce the reciprocating mass, which requires less energy to operate. The less drag on the motor, the more power available to you
Product Features:
See More
Product Features:
- Made From Premium Grade Aerospace Chrome Moly
- Center Less Ground To Precise Diameter
- Hollow Core Serves To Reduce The Reciprocating Mass, Which Requires Less Energy To Operate
- Provide With Required Reliability And Improved Performance
Popular 1958 Chevrolet Corvette Fuel and Emissions Systems Categories
1958 Chevrolet Corvette Fuel and Emissions Systems
You count on your 1958 Chevrolet Corvette to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Fuel and Emissions Systems. With 16 Fuel and Emissions Systems ranging in price from $2.99 to $380.99, you’re sure to find everything you need for your 1958 Chevrolet Corvette.
Brands matter. If you want to shop a specific Fuel and Emissions Systems brand, we stock 9 different brands like Felpro, Mr. Gasket, and Holley. 1958 Chevrolet Corvette Fuel and Emissions Systems start as low as $2.99!
One of the best ways to find top quality OEM or aftermarket Fuel and Emissions Systems is by asking professionals. Short of that, you can shop with confidence thanks to our 164 extensive product reviews on 1958 Chevrolet Corvette Fuel and Emissions Systems. Some of the top-rated Fuel and Emissions Systems products we carry are Sbc Blk Off Plate W/Bolts with 4.0 stars.
Did we mention you can order your Fuel and Emissions Systems from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Fuel and Emissions Systems inventory for your 1958 Chevrolet Corvette below to get started!
Top-Rated Fuel and Emissions Systems Brands For Your 1958 Chevrolet Corvette
Trusted Fuel and Emissions Systems OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1958 Chevrolet Corvette running right for years to come. In our inventory you’ll find brands like Felpro, Mr. Gasket, Holley, and even more.
Popular Felpro Fuel and Emissions Systems
You’ll find popular Felpro brand products across Fuel Pumps. All are waiting to get your 1958 Chevrolet Corvette back on the road. Some of the top-rated Felpro products in these categories are:
Top-Rated Mr. Gasket Fuel and Emissions Systems
If Mr. Gasket are what you’re looking for, our inventory holds plenty. We stock Mr. Gasket brand Fuel and Emissions Systems for your 1958 Chevrolet Corvette, and some of our most reviewed Mr. Gasket parts include:
FAQs for 1958 Chevrolet Corvette Fuel and Emissions Systems
What are the most purchased Fuel and Emissions Systems for the 1958 Chevrolet Corvette?
Out of 16 Fuel and Emissions Systems for the 1958 Chevrolet Corvette, the most popular in our inventory are:
from
$24.99
This product is not rated
Locking Fuel Cap: 10491, Push In, Direct Fit, Provides Tight Seal, 1 Pack
Gas Caps
What are the top-rated 1958 Chevrolet Corvette Fuel and Emissions Systems?
Top-rated Fuel and Emissions Systems for your 1958 Chevrolet Corvette based on customer reviews/ratings are:
from
$12.99
(1)
Sbc Blk Off Plate W/Bolts
“application chart said it wouldnt fit 92 chevy 5.7 but it does”
