Volvo 240 Differentials

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

Product Features:

• Brand may vary by location

Yukon Carrier Installation Kits are a convenient and low-cost solution for carrier changes in cases where one is upgrading to a positraction limited slip differential, a mechanical locker, or an air operated locker. These kits contain carrier bearings and races and a carrier shim kit.

Product Features:

• Fits Dana Spicer 30
• Includes carrier bearings and races and carrier shim kit

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit is used in 8.5″ differentials using a Yukon Dura Grip, Eaton posi, ValueTrac, True Trac, Pro-Series Auburn, Detroit Locker or standard carrier with large bearing journals. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application. Includes Supershims.

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits Dana Spicer 30
• Works with Spartan Locker or standard open spider gears

Yukon Pinion Installation Kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings and races can be reused. This kit features Timken bearings and races along with high-quality seals and small parts. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your gear set.

Product Features:

• Fits Dana Spicer 30 rear
• Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver select ability.

Product Features:

• O-ring for seal housing
• Fits Dana Spicer 30 and AMC Model 35

Yukon Gear & Axle offers a full line of top quality differential tools to save time and money.

Product Features:

• Fits M86610 race
• All-steel construction
• For accurate installation of bearing races

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• DANA-30 FORD MASTER BRG KIT

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

• Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
• Left hand thread

Yukon shim kits are precision machined and tailored for each individual application to ensure you have the right shims for every set up.

Product Features:

• Pinion depth shims for AMC Model 35 and Chrysler 7.25″

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

Cut to length axle shaft for GM 10.5″ 14 bolt truck. This axle shaft covers lengths from 34.8″ to 38.8″. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a 38 spline upgraded shaft. The factory spindles will need to be machined in order to accept these axles. Please verify bolt pattern on 2011 & later models. This axle has a 3.562″ bolt pattern. Some late model applcaitons use a larger bolt pattern.

Product Features:

• Outer oil slinger for Dana Spicer 25, 27, 30, 44 and 50

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Oil baffle for Dana Spicer 30, Dana Spicer 44 IFS, Dana Spicer 50, AMC Model 35 IFS

Redline Heavy Shockproof Gear Oil is formulated to provide lasting protection. This kit includes four quarts of oil and a bottle of Yukon Limited Slip Friction modifier that reduces noise and chatter in clutch driven positraction units and limited slip differentials.

Product Features:

• Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

These Yukon replacement diff covers are a direct bolt-on.

Product Features:

• Fits standard rotation Dana Spicer 30
• Steel

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Roll pin for Dana Spicer 30 and Dana Spicer 44
• 0.235″ diameter

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion nut for Dana Spicer 25, 27, 30, 44, 50 and GM 7.75″
• 3/4″ x 16 thread

Spartan spring & pin kit, fits smaller designs.

Product Features:

• Replacement spring and pin kit for Spartan Locker
• Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
• Includes 4 springs and 4 alignment pins

Yukon Gear and Axle manufactures a complete line of general replacement and performance series of pinion yokes for many street, racing, and heavy-duty off-road applications.

Product Features:

• Fits Dana Spicer 44
• 26 spline
• 1310 u-joint size
• 3.219″ snap ring span
• 1.062″ cap diameter
• Outside snap ring design
• Strap style

Product Features:

• DANA-30 R&P 3:73 RATIO (STD. CUT)

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Side gear thrust washer for Dana Spicer 25, 27, 30 and AMC Model 35
• 1.560″ I.D.
• Fits standard open differentials only

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Power Lok button kit
• Fits Dana Spicer 30, 44 and Chrysler 8.75″

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

• Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
• 1/2″ head

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:

• Fits Dana Spicer 30 with 30 spline axles
• 3.73 and up ratio only
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA