Volvo 142 Differentials

Dana 30 & Dana 44 roll PIN, 0.235″ DIA, for cross pin shaft.

Product Features:

• Roll pin for Dana Spicer 30 and Dana Spicer 44
• 0.235″ diameter

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

• Pinion nut for Dana Spicer 25, 27, 30, 44, 50 and GM 7.75″
• 3/4″ x 16 thread

Dana 25, Dana 27, & Dana 30 side gear Thrust washer.

Product Features:

• Side gear thrust washer for Dana Spicer 25, 27, 30 and AMC Model 35
• 1.560″ I.D.
• Fits standard open differentials only

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

• Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
• Left hand thread

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

• Powr Lok button kit
• Fits Dana Spicer 30, 44 and Chrysler 8.75″

Replacement pinion nut washer for Dana 25, 27, 30, 36, 44 & 53.

Product Features:

• Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

Product Features:

• Brand may vary by location

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM88610 race
• All steel construction

Product Features:

• DANA-30 R&P 3:73 RATIO (STD. CUT)

Yukon 1541H alloy right hand rear axle for Model 35 (drum brakes) with a 54 tooth, 2.7″ ABS ring. axle has a length of 29-1/4″ inches and 27 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H allo

Product Features:

• Pinion depth shims for AMC Model 35 and Chrysler 7.25″

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

• Fits Dana Spicer 30 rear
• Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, thread locker, marking compound with brush, and gasket.

Set-up carrier bearing kit (2 bearings, no races) LM501349. No return.

Product Features:

• Set up bearing kit
• Fits Dana Spicer 30
• Easily slips on and off carrier journals to allow for easier carrier shim adjustment

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

• Fits standard rotation Dana Spicer 30 without crush sleeve
• 7.20″ ring gear diameter
• 26 spline pinion
• 10 ring gear bolts
• 4.56 ratio

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings

Product Features:

• Spider gear kit
• Fits Dana Spicer 30 27 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Product Features:

• O-ring for seal housing
• Fits Dana Spicer 30 and AMC Model 35

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Dana Spicer 30 rear
• Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

Product Features:

• Outer oil slinger for Dana Spicer 25, 27, 30, 44 and 50

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool
• Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

Dana 28 & Dana 30 pinion gear Thrust washer. Also fits AMC Model 35 with 1.560″ side gear bore only.

Product Features:

• Pinion gear thrust washer for Dana Spicer 25, 27 and 30

Product Features:

• Carrier shim kit for Dana Spicer 30 and Dana Spicer 44 with 19 spline axles

Product Features:

• Oil baffle for Dana Spicer 30, Dana Spicer 44 IFS, Dana Spicer 50, AMC Model 35 IFS

Product Features:

• Cover gasket
• Fits Dana Spicer 30

Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 30 and 44
• 26 spline
• 1350 u-joint size
• Outside snap ring design
• 3.625″ snap ring span
• 1.188″ cap diameter
• Strap style