UD 1300 Belts and Hoses
Top UD 1300 Belts and Hoses Categories
We carry over 21 Belts and Hoses in inventory for the UD 1300. If you’re looking for aftermarket Belts and Hoses for your UD 1300, check out all these categories:
Essential UD 1300 Belts and Hoses
Gates – Green Stripe« Truck & Bus Series V-Belt (Part No.TR22448)
from
$35.99
Specifically designed for heavy-duty truck, bus and off-road equipment applications. Absorbs normal shock loads without damage to the belt.
Product Features:
See More
Product Features:
- Molded notches reduce bending stress, especially on small diameter pulleys, while dissipating heat
- High modulus, high strength tensile cord
- Oil and heat-resistant construction throughout
- Meets SAE J636b and SAE J637 specifications
- Meets RMA oil and heat resistant standards and static conductivity requirements
- NOTE: Some sizes available as Gates PowerBand joined V-belts
Gates – Automotive XL« High Capacity V-Belt (Part No.9565)
from
$42.49
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
- Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
- Resists oil, heat, ozone, weather and aging for improved belt life
- Meets or exceeds SAE J636C specifications
Gates – Green Stripe« Truck & Bus Series V-Belt (Part No.TR22514)
from
$41.99
Specifically designed for heavy-duty truck, bus and off-road equipment applications. Absorbs normal shock loads without damage to the belt.
Product Features:
See More
Product Features:
- Molded notches reduce bending stress, especially on small diameter pulleys, while dissipating heat
- High modulus, high strength tensile cord
- Oil and heat-resistant construction throughout
- Meets SAE J636b and SAE J637 specifications
- Meets RMA oil and heat resistant standards and static conductivity requirements
- NOTE: Some sizes available as Gates PowerBand joined V-belts
Driveworks – Automotive V-Belt, Driveworks (Part No.37017)
from
$5.29
The Driveworks V-Belt is manufactured with top quality components to deliver the maximum power and performance on all passenger cars and light duty trucks in service today.
Product Features:
See More
Product Features:
- This belt is made with bottom cogs to provide the maximum flexibility and grip required on v-belt drives
- Polyester cords provide extreme tension-holding capability for longer belt life
- The raw edge belt design delivers the maximum gripping power
- The highly engineered rubber compounds are resistant to under hood heat and ozone deterioration
Gates – FleetRunner« Heavy-Duty V-Belt (Part No.9355HD)
from
$39.99
Designed for the toughest applications, FleetRunner construction provides superior flexibility, stability, load capacity, and unsurpassed belt life. Patented materials deliver peak performance at extreme prolonged operating temperatures making this belt the ultimate problem solver. An advanced blend of EPDM rubber technology withstands the modern threats of deterioration from increased exposure to ozone and water-based coolants. FleetRunner does this all while providing the lowest cost per mile for fleets, including 3/4 and 1 ton pickups.
Product Features:
See More
Product Features:
- Patented material provides peak performance at extremely prolonged operating temperatures
- Heavy-duty construction resists cracking, wear, oil and heat
- Special compound provides unmatched stability, load carrying capacity and belt life
- Unique undercord notch pattern offers increased flexibility for smaller diameter pulleys
- Problem solver for troubled drives
- Engineered to save your fleet money and reduce downtime
- Meets RMA oil and heat resistant standards and static conductivity requirements
Gates – Hi-Power« II Classical Section Wrapped V-Belt (Part No.A37)
from
$13.99
Featuring a composite, multi-purpose construction, these belts resist oil and heat, ozone, sunlight, weather, and aging. Suitable for all industrial applications, including v-flat drives.
Product Features:
See More
Product Features:
- Smoother running with less slip and wear for excellent belt service life and reduced pulley wear
- High-quality rubber compound protects the belt against heat, ozone and sunlight
- Proprietary Flex-Weave cover is a patented fabric construction, providing extended protection to the belt core from oil, contaminants and heat for longer belt life
- Flex-bonded cords strongly adhere to the body of the belt, resulting in equal load distribution and absorption of bending stress, fatigue and shock loads without cord deterioration
- Meets RMA oil and heat resistant standards and static conductivity requirements
- Temperature Range: -22 Deg. F to +140 Deg. F (-30 Deg. C to +60 Deg. C)
- NOTE: Available in A, B, C, D and E cross-sections as well as Hi-Power II PowerBand V-belts
Gates – Premium Molded Coolant Hose (Part No.20782)
from
$27.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Premium Molded Coolant Hose (Part No.20065)
from
$19.49
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 12" Long, 1.50" Diameter (Part No.B70081)
from
$24.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
UD 1300 Belts and Hoses Categories
Helping You Find the Right Belts and Hoses for Your UD 1300
You love your 1300. So we’ve made it easier than ever to help you find UD 1300 Belts and Hoses in our online catalog. Our inventory holds 21 aftermarket and OEM Belts and Hoses for your UD 1300, ranging from $5.29 to $102.99.
We offer parts from 3 brands trusted to make quality Belts and Hoses for your UD 1300. Before you buy, take some time to read through customer reviews. We currently have 34 reviews of UD 1300 Belts and Hoses from previous customers.
Find your 1300 Belts and Hoses here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your UD 1300 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Belts and Hoses Brands for Your UD 1300
Our inventory holds Belts and Hoses for your UD 1300 from 3 trusted brands. You’ll find OEM and aftermarket parts from brands like Dayco, Gates, and Driveworks, all of which can keep that UD happy.
We have Dayco parts available for your UD 1300 in categories like Serpentine and V Belts and Radiator Hoses. Some of the top-rated Dayco parts in these categories are:
from
$24.99
(16)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 12" Long, 1.50" Diameter
Coolant Hoses
FAQs for UD 1300 Belts and Hoses
What are the most purchased Belts and Hoses for the UD 1300?
Out of 21 Belts and Hoses for the UD 1300, the most popular in our inventory are:
