Toyota Van Belts and Hoses

Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.

Product Features:

• Metal line kit
• For use in engine oil cooler applications
• Routes oil lines past exhaust manifolds
• Provides protection where standard hoses can fail

1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.

Product Features:

• Engine oil cooler hose
• Size: 1/2″ x 12′
• Designed for engine oil applications
• 12′ hose length accommodates most applications

Dayco® High Performance V-Belt is the workhorse of the heavy-duty industry. Polyester cord provides maximum power transfer and tension holding capability for the life of the belt. The laminated construction helps absorb greater shock loads associated with diesel engines. These Dayco® High Performance V-Belt advantages translate into less downtime, lower maintenance costs, and increased dependability. Dayco’s High Performance V-Belt meets or exceeds SAE J636 and J637 specifications.

Product Features:

• The High Performance V-Belt design delivers more flexibility and increases airflow around the belt, so it runs cooler and lasts longer than most competitive belts
• Polyester cord provides maximum power transfer and tension holding capability for the life of the belt
• The laminated construction helps absorb greater shock loads associated with diesel engines
• Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds

Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.

Product Features:

• Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
• Form-ground to ensure precise top width and sidewall dimensional control for proper fit to the pulley
• Thermally-active tensile cords for maintenance-free performance when properly installed and tensioned
• Resists oil, heat, ozone, weather and aging for improved belt life
• Meets or exceeds SAE J636C specifications

The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl

Product Features:

• Designed to meet OE specifications
• Not suitable for oil or heat transfer
• Meets SAE J20R4, Class D-2 requirements for improved service hoses
• This hose is designed to prevent splitting, ballooning, and elongation

Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.

Product Features:

• Specifically-engineered materials resist collapse under vacuum
• Engineered to resist electrochemical degradation, the leading cause of hose failure
• Pre-shaped to fit and to ensure perfectly sealed conditions
• EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
• Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Dayco idler/tensioner pulleys are built with smoother surfaces and tighter dimensional tolerances, which translates to less vibration and longer belt life. In addition to stamped, forged steel and powdered metal pulleys, Dayco also designs ultra-strong plastic pulleys with specially formulated glass-filled polymers that resist wear and tear. Premium lubricated ball bearings and double high temperature seals ensure peak bearing performance, the most critical element of a pulley’s service life.

Product Features:

• Designed for the majority of automotive vehicle applications on the road today
• High-quality materials help resist wear and improve belt life
• Features premium lubricated bearings to extend service life
• Meets or exceeds OE quality

Dayco, Acc. Belt Idler Pulley

Premium hose constructed for long service life.

Product Features:

• Good resistance to high temperatures for extended periods of time
• Similar to SAE 20R3 Class D-3
• Temperature rating: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• CAUTION: Do not use for fuel or oil transfer applications.

Premium hose constructed for long service life.

Product Features:

• Good resistance to high temperatures for extended periods of time, which prolongs service life
• Meets SAE 20R3 Standard Wall Class D-2 requirements
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• CAUTION: Do not use for fuel or oil transfer applications
• CAUTION: Do not use for fuel or oil transfer applications
• PLEASE NOTE: Item is priced and sold by the foot. See store for details.

Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers  more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile

Product Features:

• Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
• Engineered to help address noise issues caused by the belt drive 
• Capable of handling more extreme temperatures and workloads

Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture

Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.

Product Features:

• Has all the quality features of Gates molded coolant hose and similar to OEM specifications
• Engineered to resist electrochemical degradation ┐ the leading cause of hose failure
• EPDM tube, synthetic fiber knit reinforcement, EPDM cover
• Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
• Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
• Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.

Product Features:

• Meets the requirements of SAE J20R3, Class D-1
• Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Engineered as an OEM replacement
• The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture

This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made in the U.S.A. to the O.E. specified design and meets all performance and durability requirements. Heavy duty steel construction. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket._

Product Features:

• Manufactured by one of the largest original equipment part suppliers in the world to ensure proper form, fit, and performance
• Heavy Duty Steel Pulley with close tolerance ball bearing pocket and Electro-deposited coating for superior corrosion resistance
• Installation instructions included.

Product Features:

• Improved sealing surface for greater leak resistance
• High flexibility for easy installation
• Maximum vehicle coverage with minimum inventory
• Resistant to heat, oil and ozone
• Rated for SAE 20R5 Class D-2 performance
• Temperature Range: up to +257 Deg. F (+125 Deg. C)
• Note: Gates recommends replacing clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.

Product Features:

• Meets SAE J20R4, Class D-1 requirements
• Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
• Provides excellent protection against external elements

Product Features:

• Improved sealing surface for greater leak resistance
• High flexibility for easy installation
• Maximum vehicle coverage with minimum inventory
• Resistant to heat, oil and ozone
• Rated for SAE 20R5 Class D-2 performance
• Temperature Range: up to +257 Deg. F (+125 Deg. C)
• Note: Gates recommends replacing clamps each time a new coolant hose is installed
• Caution: Do not use for fuel or oil transfer applications

Premium hose constructed for long service life.

Product Features:

• Good resistance to high temperatures for extended periods of time, which prolongs service life
• Meets SAE 20R3 Standard Wall Class D-2 requirements
• Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
• CAUTION: Do not use for fuel or oil transfer applications
• CAUTION: Do not use for fuel or oil transfer applications
• PLEASE NOTE: Item is priced and sold by the foot. See store for details.

Radiator Hose

The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent spl

Product Features:

• Designed to meet OE specifications
• Not suitable for oil or heat transfer
• Meets SAE J20R4, Class D-2 requirements for improved service hoses
• This hose is designed to prevent splitting, ballooning, and elongation