Subaru GL-10 Belts and Hoses
Top Subaru GL-10 Belts and Hoses Categories
We carry over 36 Belts and Hoses in inventory for the Subaru GL-10. If you’re looking for aftermarket Belts and Hoses for your Subaru GL-10, check out all these categories:
Essential Subaru GL-10 Belts and Hoses
Dayco – Molded Heater Hose; EPDM Rubber, 5/16 Inch Diameter, 8 1/4 Inch Length (Part No.86800)
from
$36.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Gates – ThermalPro Premium Molded Coolant Hose (Part No.20338)
from
$9.79
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Materials specifically designed to resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube; synthetic fiber knit reinforcement; heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing clamps and connectors every time a new cooling hose is installed.
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10" Long, 1.13" Diameter (Part No.B71277)
from
$26.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Automotive XL High Capacity V-Belt (Part No.9425)
from
$27.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- The fiber-reinforced rubber adds flexibility along the entire length of the belt and ensures greater lateral stability in the pulley.
- The shape is rectified to ensure precise dimensional control of the top width and side wall for a proper fit to the pulley.
- Thermoactive traction ropes for maintenance-free performance when properly installed and tensioned
- Resistant to oil, heat, ozone, weathering and aging for a longer belt life.
- Meets or exceeds SAE J636C specifications
Gates – Automotive XL High Capacity V-Belt (Part No.9480)
from
$31.99
Replacement belt for the most demanding engine drives. Due to thermal forces, this variable notched belt actually tightens on the drive as it gets hot. This results in improved belt performance by reducing tension decay and noise.
Product Features:
See More
Product Features:
- Fiber-loaded rubber stock adds flexibility along the length of the belt and provides greater lateral stability in the pulley
- The shape is rectified to ensure precise dimensional control of the top width and side wall for a proper fit to the pulley.
- Thermoactive traction ropes for maintenance-free performance when properly installed and tensioned
- It resists oil, heat, ozone, weather, and decay to improve belt life.
- Meets or exceeds SAE J636C specifications
Dayco – Bottom Cog V-Belt: 44.75" Long, Exact Fit Premium Quality (Part No.17448)
from
$20.29
Top Cog Belt is the workhorse of the heavy-duty industry. The cogs in the top of the belt deliver increased flexibility around small pulleys, and the increased surface area results in a cooler running belt. Polyester cord provides maximum power transfer and tension holding capability for the life of the belt. The laminated construction helps absorb greater shock loads associated with diesel engines. These Top Cog advantages translate into less downtime, lower maintenance costs, and increased dependability. Top Cog Belt meets or exceeds SAE J636 and J637 specifications.
Product Features:
See More
Product Features:
- The Top Cog design delivers more flexibility and increases airflow around the belt, so it runs cooler and lasts longer than most competitive belts
- Polyester cord provides maximum power transfer and tension holding capability for the life of the belt
- The laminated construction helps absorb greater shock loads associated with diesel engines
- Made with specially formulated rubber compounds, this belt is highly resistant to extreme under hood temperatures that can cause premature damage to under engineered rubber compounds
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10.25" Long, 1.13" Diameter (Part No.B71404)
from
$41.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 11" Long, 1.13" Diameter (Part No.B71260)
from
$14.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Flex Radiator Hoses; EPDM Rubber, 11 Inch Long, 1.25 Inch Inner Dia. (Part No.81031)
from
$30.99
The Dayco flex radiator hose replaces straight or molded radiator hoses on a wide range of engine applications. Precision molded in standard lengths, it features a knitted reinforcement and synthetic EPDM construction. This hose is designed to prevent splitting, ballooning and elongation as well as resist ozone and other detrimental environmental elements, coolants and temperature variations of -40øF (-40øC) to +257øF (+125øC). With corrugations that provide excellent hose flexibility without flattening or collapsing, the Dayco flex radiator hose also features a helical steel coil spring for increased flexibility.
Product Features:
See More
Product Features:
- Designed to meet OE specifications
- Not suitable for oil or heat transfer
- Meets SAE J20R4, Class D-2 requirements for improved service hoses
- This hose is designed to prevent splitting, ballooning, and elongation
Gates – Premium Molded Coolant Hose (Part No.21584)
from
$24.29
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- The specially designed materials resist collapse under vacuum.
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube; reinforced with knitted synthetic fibers; EPDM lid resistant to heat, ozone, and chemical refrigerants
- It meets the requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- temperature range Deg. F to +257 degrees F (-40 degrees C to +125 degrees C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Warning: Do not use for fuel or oil transfer applications
Gates – Premium Molded Coolant Hose (Part No.21779)
from
$38.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Gates – Vulco-Flex II Flexible Coolant Hose (Part No.25251)
from
$30.99
Gates Vulco-Flex(R) II hose will bend in almost any direction. It easily replicates the angles and planes of a wide variety of expensive original equipment coolant hose, for quick, easy replacement.
Product Features:
See More
Product Features:
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimal inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature range: up to +257 Degrees F (+125 Degrees C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transport applications.
Imperial – Transmission Oil Cooler Hose (Part No.248001)
from
$32.49
Our products are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile a/c experience, fix it once and fix it right with Imperial.
Product Features:
See More
Product Features:
- Transmission oil cooler hose
- 11/32″ x 4-1/2′
- Designed for transmission fluid applications
- Made for tight-radius applications found in transmission cooler installations
- Compatible with 11/32 in. OEM cooler systems
- Tube made of black chemigum (nitrile)
- Reinforced with 2-spiral synthetic
- Covered in black Hypalon
- Compatible with 11/32 in. OEM cooler systems
- Tube made of black chemigum (nitrile)
- Reinforced with 2-spiral synthetic
- Covered in black Hypalon
Imperial – Engine Oil Cooler Hose (Part No.240112)
from
$48.99
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
- Size: 1/2 in. x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
- Medium duty applications
Imperial – Metal Line Kit for Engine Oil Cooler (Part No.240293)
from
$59.99
Our products are engineered and tested to provide years of trouble free operation. Backed by over 50 years of mobile a/c experience, fix it once and fix it right with Imperial.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
- Used on Chevrolet V8 applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
- Comes with all parts needed for the job
Gates – Premium Molded Heater Hose (Part No.18020)
from
$17.79
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- It has all the quality characteristics of Gates molded coolant hose and is similar to OEM specifications.
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Compliant with SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transport applications.
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 14 1/4 Inch Length (Part No.87649)
from
$12.99
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Straight Heater Hose; EPDM Rubber, 5/8 Inch Diameter (sold by foot) (Part No.80271)
from
$1.99
Specifically designed to carry the heated coolant from the engine block to the heater core under the dashboard and return it to the engine, this Dayco Standard Heater Hose is constructed using all EPDM compounds and spiral reinforcement for high burst strength and excellent heat resistance. Made for general service on light trucks and passenger cars, this hose is similar to SAE 20R3, Class D-2 and has a temperature rating of -40 Degree F (-40 Degree C) to +257 Degree F (+125 Degree C). This Dayco Standard Heater Hose is compatible with all common coolant and coolant additives. Note: This hose is NOT suitable for fuel or oil transfer.
Product Features:
See More
Product Features:
- Specifically designed to be compatible with all common coolants and coolant additives
- Constructed using all EPDM compounds and spiral reinforcements
- Similar to SAE 20R3, Class D-2
- Has a high burst strength and excellent heat resistance of -40 Degree F (-40 Degree C) to +257 Degree F (+125 Degree C)
- PLEASE NOTE: Item is sold and priced by the foot. See store for details.
Subaru GL-10 Belts and Hoses Categories
Helping You Find the Right Belts and Hoses for Your Subaru GL-10
You love your GL-10. So we’ve made it easier than ever to help you find Subaru GL-10 Belts and Hoses in our online catalog. Our inventory holds 36 aftermarket and OEM Belts and Hoses for your Subaru GL-10, ranging from $1.99 to $59.99.
We offer parts from 4 brands trusted to make quality Belts and Hoses for your Subaru GL-10. Before you buy, take some time to read through customer reviews. We currently have 2,449 reviews of Subaru GL-10 Belts and Hoses from previous customers. Some of the top rated parts include Bottom Cog V-Belt: 36" Long, Exact Fit Premium Quality with 4.8 stars and Bottom Cog V-Belt: 35.5" Long, Exact Fit Premium Quality with 4.8 stars.
Find your GL-10 Belts and Hoses here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Subaru GL-10 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Belts and Hoses Brands for Your Subaru GL-10
Our inventory holds Belts and Hoses for your Subaru GL-10 from 4 trusted brands. You’ll find OEM and aftermarket parts from brands like Imperial, Dayco, and Gates, all of which can keep that Subaru happy.
We have Driveworks parts available for your Subaru GL-10 in categories like Serpentine and V Belts. Some of the top-rated Driveworks parts in these categories are:
Top-Rated Imperial Belts and Hoses
Leading Imperial Belts and Hoses
We carry Imperial brand parts for your Subaru GL-10 across several catalog categories, including Transmission Cooler Hoses. Some of our most reviewed Imperial parts include:
FAQs for Subaru GL-10 Belts and Hoses
What are the most purchased Belts and Hoses for the Subaru GL-10?
Out of 36 Belts and Hoses for the Subaru GL-10, the most popular in our inventory are:
from
$14.99
(30)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 11" Long, 1.13" Diameter
Coolant Hoses
from
$1.99
This product is not rated
Straight Heater Hose; EPDM Rubber, 5/8 Inch Diameter (sold by foot)
Heater Hoses
from
$6.99
(7)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 3.25" Long, .63" Diameter
By-Pass Hoses
What are the top-rated Subaru GL-10 Belts and Hoses?
Top-rated Belts and Hoses for your Subaru GL-10 based on customer reviews/ratings are:
from
$14.29
(11)
Bottom Cog V-Belt: 35.5" Long, Exact Fit Premium Quality
“I replaced the belts in my NA Miata and this worked great. The build quality was on par with an OEM belt. Installation was a breeze and they have gone”
from
$30.99
(3)
Flex Radiator Hoses; EPDM Rubber, 11 Inch Long, 1.25 Inch Inner Dia.
“well satisfied”
