Scion xA Engine Cooling Parts

The Mahle Engine Coolant Thermostat Gasket is a high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

• Seals the thermostat housing and helps prevent coolant from leaking from the engine for proper engine temperature
• Premium Original Equipment replacement
• Provides performance and dependability
• Manufactured to meet OE specifications

Permatex Water Pump & Thermostat RTV Silicone Gasket Maker is a noncorrosive, sensor-safe RTV silicone gasket material formulated for water pumps and thermostat housings. Permatex Water Pump & Thermostat has the highest water-glycol resistance available in an RTV silicone.

Product Features:

• Sensor-safe, noncorrosive RTV silicone gasket material
• Formulated specifically for water pumps and thermostat housings
• Highest water-glycol resistance available in RTV silicone
• Superior adhesion and flexibility
• Can be used as a gasket maker or dressing

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

• OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
• FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
• THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

Reservoir Cap

All modern vehicles consist of several independent operating systems controlled by a main system processor with independent sub-processors. The sub-processors provide class 2 serial information data to the main processor while handling the operation of the system and carry the circuit load to protect the main operating system. When replacing any level processor programming may be needed to enter the unit into the vehicles main operating system.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

THERMOSTAT SEAL

The AISIN Water Pump contains no remanufactured parts and provides optimal cooling without creating excess load to the engine. The highest quality materials are used, creating stronger body design and resistance to corrosion.

Product Features:

• OE-Equivalent and direct fit application.
• 100% new with no remanufactured parts.
• Advanced technological design.
• Carbon ceramic sealing.
• Resistant to corrosion.
• Optimum cooling performance and longevity.

The Sankei Switches radiator cap range has been developed to operate within original equipment manufacturer’s specifications. A faulty radiator cap can cause your car to boil-over at a lower temperature. Test or replace the coolant cap when servicing the cooling system.

Product Features:

• Meets Original Equipment specifications.
• Made from premium materials.
• Designed to function on open cooling systems and overflow reservoir type systems.

This premium upgraded thermostat is everything you were looking for. UltraStat Thermostats are the toughest thermostats on the market. All heavy gauge stainless steel construction provides long-life durability, as well as complete corrosion resistance. Exclusive BLVT Valve technology minimizes thermal shock to cooling system components. This is the perfect upgrade to help insure your cooling system is working exactly as you need and expect it to for longevity.

Product Features:

• Heavy gauge stainless steel components offer increased reliability and long-lasting durability
• Exclusive BLVT Valve Technology minimizes thermal shock to cooling system components
• Stainless steel thermal element for unmatched corrosion resistance and revolutionary REAX wax mixture provides quicker reaction time
• AccuSpring Design for stable temperature control and increased cabin comfort

This radiator drain petcock is a direct replacement for the original equipment plug that may have deteriorated or corroded. Made of quality materials, this petcock is engineered to strict standards for durable use over time.

Product Features:

• Direct replacement – this radiator drain petcock matches the fit and function of the original equipment part.
• Durable construction – this part is made of quality materials for a long service life
• Saves money – offers original equipment quality at a competitive price
• Quality assured – this petcock has undergone virtual testing to assure proper fit and function

This engine cooling fan assembly is precision-engineered to match the fit and performance of the stock radiator fan on specific vehicle years, makes and models. It has been rigorously tested to ensure it cools as effectively as the original part.

Product Features:

• Ideal replacement – this engine cooling fan assembly was precision-engineered to match the fit and performance of the stock radiator fan assembly on specific vehicles.
• Complete package – assembly is designed with the same materials and components as the original part.
• Quality assured – motors are tested in laboratory settings to ensure performance
• Cost effective and reliable – trustworthy manufacturing for far less than same part at the dealership

This engine coolant filler neck is designed to match the fit and function of the original neck on specified applications. Made of quality materials, it is engineered for reliable performance and durability.

Product Features:

• Direct replacement – this engine coolant filler neck is designed to match the fit and function of the original neck on specified applications.
• Restores functionality – reliable replacement for an original part that has cracked or failed due to heat, vibration or fatigue.
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Carquest Premium radiators are designed and engineered for maximum performance, using the highest-grade materials to ensure all radiators meet or exceed original equipment (O.E.) fit, form and function. Carquest Premium radiators are built by manufacturers that meet IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. Most modern vehicles use radiators with plastic tanks and our parts are engineered with integrated ribbing to prevent damage during thermal cycling. Carquest Premium radiators are also 100% tested to ensure a durable, leak-free cooling system repair.

Product Features:

• Thermal tested under real-life temperature simulations
• High tensile strength aluminum for maximum crimp strength
• Plastic tanks are engineeredáwith integrated ribbingáfor addedástrength to withstand cracks, bowing and distortion during thermal cycles
• Thermal expansion slots extend core life and reduce failure rates by allowing improved core expansion and contraction during systematic heat cycles

Product Features:

• Our units are all pre-aligned & pre-adjusted to save installation time and ensure proper switching.
• A lubricated felt pad that lubricates the cam lobes on the vehicles distributor. This reduces wear on the point set rubbing block, extending the usable life of the part.
• Ventilated where available, tungsten contacts, which run cooler and exhibit less erosion.
• The copper-alloy shunt provides superior resistance to breakage, due to the flexing of the moving arm on the point set. It also significantly increases current conductivity over typical steel, shunts.

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered and manufactured specifically for the repair environment
• Unsurpassed quality you can trust
• Validated for fit, form, and function

This replacement engine coolant thermostat housing is engineered to match the fit and durability of the stock thermostat housing on specified vehicles. It is designed to withstand extreme temperature changes to extend service life.

Product Features:

• Ideal replacement – this engine coolant thermostat housing directly replaces the original housing on specified vehicle years, makes and models.
• Durable construction – this part is specifically designed to withstand extreme temperature changes and resist cracking and leaking.
• Cost-effective and reliable – offers original manufacturer quality at lower cost than getting replacement at dealer
• Industry-leading design – professionally engineered by the aftermarket leader in replacement thermostat housings

Permatex’s The Right Stuff 1 Minute Series offers the fastest return to service in just 1 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 1 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:

• Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
• Sensor-safe, non-corrosive, RTV silicone
• Protects against leaks caused by vibration and thermal expansion
• Meets performance specs of OE silicone gaskets
• Quickly returns vehicle to service in just 1 minute

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

• High torque and rigidity
• Sensor-safe, non-corrosive formula
• OEM specified
• Low-odor, non-corrosive formula
• Ideal for closed spaced bolt patterns

MAHLE Cleveite Inc. is not responsible for failures resulting from owner, operator or third party abuse or neglect including, but not limited to engine operation without adequate lubricant or coolant, over or under-fuelling, over-speeding, lack of proper maintenance to cooling, lubrication or air intake systems, improper storage, starting, warm-up, run-in or shutdown procedures or the continued operation of an engine after the first sign of a malfunction. MAHLE Cleveite Inc. is not responsible for failures resulting from improper installation or repair procedures, alteration or the misapplication of parts, or use in engines modified for competition or levels of performance beyond the engine manufacturers original specifications. Mahle/Cleveite – (The MAHLE Group) is one of the largest global automotive parts manufacturers, specializing in Engine Components, Filtration and Peripherals.

Tester adapter for the MT-300 cooling system pressure testers. Professional grade test equipment to ensure an automotive cooling system is operating at the correct pressure. Made from high quality materials to ensure durability. Designed to test automotive coolant caps.

Product Features:

• Machined metal construction
• Works with MT-300 pressure tester
• Tests coolant caps
• Professional quality

An integral part of the drive system for belt-driven water pumps. Dorman’s Engine Water Pump Pulley is recommended for replacement whenever you service the water pump.

Product Features:

• Stamped steel construction for long-lasting durability
• High strength coating for corrosion resistance
• Direct replacement for a proper fit every time
• Easy installation

Damaged your engine water pump pulley? This pulley is a direct replacement for the original manufacturer’s part on specific vehicle years, makes and models, restoring proper performance.

Product Features:

• Direct replacement – this engine water pump pulley matches the fit and function of the original part on specific vehicles.
• Durable design – built to withstand the elements and road debris.
• Thoroughly tested – must pass strict standards to ensure reliable longevity
• Trustworthy quality – backed by team of engineers and inspectors in United States