Saab 9-7X Air Intakes

The ACDelco GM Original Equipment Throttle Position Sensor is a GM-recommended replacement for your vehicle’s original component. The TPS reports the throttle position to the engine control module, which uses the signal to adjust fuel delivery and ignition timing. This throttle position sensor kit meets the performance standards you would expect from General Motors.

Product Features:

• Undergo the same stringent testing process as the original part
• GM-recommended replacement part for your GM vehicle’s original factory component
• Offering the quality, reliability, and durability of GM OE
• Manufactured to GM OE specification for fit, form, and function

ACDelco GM Original Equipment Throttle Position Sensors (TPS) are electrical sensors, and are GM-recommended replacements for your vehicle’s original components. They electronically inform the engine control module (ECM) of the throttle’s plate angle or position. These signals are then used to regulate the fuel and ignition system. These original equipment throttle position sensors have been manufactured to fit your GM vehicle, providing the same performance, durability, and service life you expect from General Motors.

Product Features:

• Electronically informs the ECM of the throttle valve angle
• Used to regulate the fuel and ignition system
• GM-recommended replacement part for your GM vehicle’s original factory component
• Offering the quality, reliability, and durability of GM OE
• Manufactured to GM OE specification for fit, form, and function

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• STRONG AND DURABLE — Features molded rubber over an aluminized steel carrier which resists high heat and coolants
• SUPERIOR SEAL — Proprietary rubber sealing beads help eliminate potential leak paths for a superior seal
• EASIER TO INSTALL — Locating tabs assure proper alignment and easier installation
• PREVENTS OVERTIGHTENING — Torque limiters help eliminate overtightening and gasket splitting and extruding
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

WARNING: This item cannot be returned for a replacement or refund if opened! Mahle is the largest gasket manufacturer in the world, providing you original equipment design and quality and world class aftermarket service. Mahle does not just cut gaskets – it designs total system sealing approaches that utilize application engineering. This means that regardless of what application you are trying to seal, you can count on Mahle doing the research and testing to provide the optimum material and technology for that specific application – this systems sealing approach requires a variety of materials. No other gasket manufacturer offers the Application Engineered approach to sealing an engine. A variety of different gasket materials insure an engine gets the optimal seal. All gaskets are not created equal – Mahle gaskets prove it every day.

Product Features:

• Original equipment design and quality
• Head sets give you original equipment form, fit, and function
• Utilizes OE equivalent or better materials in all head sets
• Packaged in shrink wrapped tray
• Every part you need to complete your gasket repair in one package unless otherwise stated

When you’re serious about power for your LS or new LT1 engine, call in the AirForce! The all-new MSD Atomic AirForce intake manifold delivers improved airflow and distribution to improve the performance of stock and modified engines. The unique bell-mouthed runner entrances maximize airflow and minimize shrouding – all while optimizing the available plenum volume for an unobstructed flow path over opposing runners. The polymer molded 2-piece design allows for easy access to the runners for porting. Atomic AirForce accepts an OEM or 103mm throttle body as well as stock or aftermarket fuel rails including MSD’s Atomic LS EFI system. The intake bolts on and is supplied with new gaskets and hardware for a direct bolt-on package.

Product Features:

• Polymer Material Resists Heat Soak
• 103mm Throttle Bore For Greater Air Flow
• Direct Flow Path Runner Design
• Allows For The Use Of Stock Fuel Rails

This engine intake manifold was precision-engineered and durably manufactured to match the fit and function of the original manifold on specified vehicles. It is thoroughly tested to ensure top-quality OEM construction and superior reliability.

Product Features:

• Ideal replacement – this intake manifold was precision-engineered and durably manufactured to match the fit and function of the stock manifold on specified vehicles.
• Reliable construction – tested to ensure top-quality OEM performance and durability.
• Perfect fit – designed to match all specifications of the original part for convenient, trouble-free installation
• Trustworthy design – built by the industry leader in aftermarket manifolds

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Premium quality materials for longer service life
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

The Hitachi Electronic Throttle Body is a high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:

• OE Manufactured assemblies include Throttle Position sensors
• Controls the volume of air flowing into the engine
• Improves engine power, fuel economy and emissions performance

OE Throttle Body Assemblies. The throttle body is an essential part of the inlet air stream of the modern gasoline engine. In combination with the electronic throttle control system, the throttle body assembly is designed to control the amount of fresh air entering the engine. Manufactured in U.S.A. on OE production line.

Product Features:

• Actual OE Product
• Plug & Play – No flash update needed
• Exact fit, form, and function
• Manufactured worldwide on OE production lines
• Contains an actuator, a throttle plate and a throttle position sensor (potentiometer), which are integrated into one housing

All CARDONE 100% New Electronic Throttle Bodies are guaranteed to fit and function like the original due to our proprietary engineering standards. Each unit is built and tested as a complete assembly to ensure quick installation and reliable performance. All components match O.E., ensuring accurate air flow in all driving conditions and peak engine performance.

Product Features:

• Critical components used in manufacturing the electronic throttle body, including the housing, throttle plate, position sensors, throttle actuator motor and throttle plate return spring conform to precise O.E. dimensions.
• Each throttle body is tested for all critical functions, including response time and air flow at multiple points, ensuring an optimal fuel/air ratio.
• 100% computerized testing of motor, throttle position sensor and articulation ensures reliable and consistent performance.
• Each unit is guaranteed to fit and function like the original.

High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:

• Designed to OE standards for ease of installation
• Utilizing high grade materials to ensure peak conductivity and perfect connections
• Decades of industry leading research and development focused on meeting the technician’s needs
• With industry leading expertise, when original equipment fails our products are designed to fix the inherent failure issues

FI Throttle Body Mou

MAHLE Cleveite Inc. is not responsible for failures resulting from owner, operator or third party abuse or neglect including, but not limited to engine operation without adequate lubricant or coolant, over or under-fuelling, over-speeding, lack of proper maintenance to cooling, lubrication or air intake systems, improper storage, starting, warm-up, run-in or shutdown procedures or the continued operation of an engine after the first sign of a malfunction. MAHLE Cleveite Inc. is not responsible for failures resulting from improper installation or repair procedures, alteration or the misapplication of parts, or use in engines modified for competition or levels of performance beyond the engine manufacturers original specifications. Mahle/Cleveite – (The MAHLE Group) is one of the largest global automotive parts manufacturers, specializing in Engine Components, Filtration and Peripherals.

GM Genuine Parts Fuel Injection Throttle Body Seals are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These seals help provide an air- and liquid-tight connection between throttle body components, and are GM-recommended replacements for your vehicle’s original components. Replace this seal whenever you service the throttle body. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

• Helps prevent excess air form entering the intake
• Helps seal the intake and throttle from the elements
• Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
• GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
• GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
• GM regularly updates production and service part designs to integrate new materials and technologies

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

WVE is a leading source of advanced vehicle electronics components for replacement applications in the automotive aftermarket and original equipment applications. WVE offers high-technology manufacturing along with innovative solutions and improvements to

GM Genuine Parts Fuel Injection Throttle Body Seals are designed, engineered, and tested to rigorous standards, and are backed by General Motors. These seals help provide an air- and liquid-tight connection between throttle body components, and are GM-recommended replacements for your vehicle’s original components. Replace this seal whenever you service the throttle body. GM Genuine Parts are the true OE parts installed during the production of or validated by General Motors for GM vehicles. Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE).

Product Features:

• Helps prevent excess air form entering the intake
• Helps seal the intake and throttle from the elements
• Some GM Genuine Parts may have formerly appeared as ACDelco GM Original Equipment (OE)
• GM Genuine Parts are designed, engineered and tested to rigorous standards, and are backed by General Motors
• GM Engineers design and validate OE parts specifically for your Chevrolet, Buick, GMC, or Cadillac vehicle
• GM regularly updates production and service part designs to integrate new materials and technologies